Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
System: Park/neutral switch

Code P0850: Park/neutral switch input circuit

The computer doesn't get a proper signal from the switch that says the lever is in P or N. On manual cars (such as several Nissans) it's the neutral switch.

What's failing

Park/neutral switch

Most common cause

The signal wire to the engine computer, open or shorted, or a damaged connector.

Can I drive with this code?

Nissan assigns no limp mode, so it can usually be driven, but get it checked soon

Diagnosis for your car

What car do you have?

Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.

Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →

Symptoms

  • Check engine light on, usually once the fault repeats on two trips (Nissan's two-trip logic)
  • Hardly ever any driving symptomsOn the Versa, Nissan assigns it no limp mode.
  • On manual Versa and March models, if the reverse lights also fail, it points to the transmission switch or its connector
  • On automatics and CVTs, if the range sensor fails it may also cause crank problems in P or N, because the same part has two circuits

Most common causes

  1. 1The signal wire to the engine computer, open or shorted, or a damaged connector
  2. 2No power at the switchOn the Versa, a 10 A fuse.
  3. 3On manuals (Versa, March), the position switch bolted to the transmission, which also runs the reverse lights
  4. 4On CVTs and automatics (2007–2012 Sentra, 2008–2014 X-Trail/Rogue, Tiida), the range sensor, which has a separate output for the engine computer
  5. 5On the automatic Frontier, also the instrument cluster or the transmission computer, because the signal passes through them

From most common and easiest to check to least common.

Step-by-step diagnosis

Follow these steps

Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.

Step 1

On the scan tool, does the "P/N POSI SW" data read ON in P or N (in neutral, on manuals) and OFF in the other positions?

It's guidance: a technician with a scan tool makes the final diagnosis.

See every step and resultShow
  1. Step 1. On the scan tool, does the "P/N POSI SW" data read ON in P or N (in neutral, on manuals) and OFF in the other positions?Yes: «The signal works» · No: step 2
  2. Step 2. Is the fuse good, and is power reaching the switch?Yes: step 3 · No: «Fuse or power supply»
  3. Step 3. Is the signal wire to the engine computer OK, with no opens or shorts, and the connector clean?Yes: step 4 · No: «Wire or connector»
  4. Step 4. Is your Nissan a manual?Yes: step 5 · No: step 6
  5. Step 5. Does the neutral switch have continuity between its terminals only in neutral?Yes: «Instrument cluster or computer» · No: «Replace the neutral switch»
  6. Step 6. Does the range sensor pass its test (the same as for P0705)?Yes: «Instrument cluster or computer» · No: «Replace the range sensor»

Results

  • The signal works. Look for a bad contact at the connector and confirm the repair the way Nissan asks: driving with the engine warm above 64 km/h (40 mph) for 50 to 60 seconds.
  • Fuse or power supply. Repair the switch's fuse or power supply and check the data on the scan tool again.
  • Wire or connector. Repair the open or shorted wire, or the damaged connector. Note that the expected voltage varies by model: battery voltage on the Versa and Sentra, almost 0 V on the Frontier and Altima.
  • Replace the neutral switch. On manuals (Versa, March) it's the position switch bolted to the transmission, the same one that turns on the reverse lights. Nissan doesn't open the transmission for this code.
  • Replace the range sensor. On CVTs and automatics (2007–2012 Sentra, 2008–2014 X-Trail, Tiida) the range sensor has a separate output for the engine computer. Adjust it in N with the alignment pin and check that the engine only cranks in P or N.
  • Instrument cluster or computer. If the switch and wires pass, on the automatic Frontier also check the instrument cluster and the transmission computer, since the signal goes through them; on other models, the computer, last.
Diagnostic tip

On the scan tool, "P/N POSI SW" must read ON in P or N (neutral on manuals) and OFF in every other position. To confirm the repair, Nissan asks for a drive with a warm engine above 40 mph for 50 to 60 seconds. Note the expected voltage varies by model (battery voltage on Versa and Sentra, near 0 V on Frontier and Altima).

Can I drive with this code?

Nissan assigns no limp mode, so it can usually be driven, but get it checked soon: the computer uses this signal for fuel injection, ignition timing and idle learning.

What carmaker bulletins say2 carmaker bulletins and the vehicles they nameShow

2 service bulletins published by the US NHTSA mention this code, mostly from Ford, Land Rover (2012–2014 models).

Vehicles with service bulletins for this code

  • Ford Focus 2012–2013
Bulletin LTB00677NAS1 · 2014
Land Rover Range Rover Sport 2014

Unable to shift out of Park with a 'Gearbox Fault' message and DTCs U0001-81 and U0402-2A, from a communication issue between the CJB and TCM. Not for P0850-02, P0850-29 or P1707-72.

Open the bulletin (PDF), page 1 ↗
Bulletin ASI-44686 · 2014
Ford Focus 2012–2013

Intermittent or delayed engagement out of Park, Drive or Reverse, noise at start, intermittent, hard or no start, with or without DTCs such as P0805, P0850, P0884 and P2831.

Open the bulletin (PDF) ↗

These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.

TSS parts for this code

Pick your transmission to see the TSS parts that fit it, or open all parts of this type:

See parts →

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.