Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
System: Fluid pressure low or high

Code P0868: Transmission fluid pressure low

Transmission fluid pressure is lower or higher than the computer expects. It can be the fluid level, a clogged filter, the pump, the pressure solenoid or the sensor that measures it.

What's failing

Fluid pressure low or high

Most common cause

Low fluid level

Can I drive with this code?

Better not to keep driving

Diagnosis for your car

What car do you have?

Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.

Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →

Symptoms

  • Slipping or no acceleration; on Nissan CVTs, judder when pulling away (belt slip)
  • Slow to engage D or R, or no drive; on 2022–2023 Ram 2500 and 3500 (US), slow engagement on the first start after sitting, with P0944
  • Limp modeOn 2024 Ram 2500 and 3500 with the 68RFE, Chrysler documented limp-home with P0868 and P0944.
  • Check engine light on; on Nissan JF015E CVTs this code does turn the light on after Nissan's reprogramming

Most common causes

  1. 1Low fluid levelIf it started after a fluid change, check the level first.
  2. 2A plugged, cracked or misinstalled filterOn the 545RFE, Chrysler checks that the filter seal isn't sitting on the filter neck instead of in the pump bore.
  3. 3The main regulator valve sticking in the valve body (Chrysler) or, on CVTs, a worn pump flow control valve, per the rebuilding industry
  4. 4The pump or an internal partChrysler ends at the pump when everything else checks good, and on the 2024 Ram with the 68RFE it replaced a rear selective thrust plate.
  5. 5The converterOn 2011–2017 62TE units (US), a cracked piston set P0740, P0868 and P0944 together.
  6. 6On Nissan CVTs, the beltNissan removes the valve body and inspects it; if it slipped, it replaces the CVT; if not, only the valve body.

From most common and easiest to check to least common.

Step-by-step diagnosis

Follow these steps

Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.

Step 1

Is the fluid at the right level?

If the code started after a fluid change, check the level first.

It's guidance: a technician with a scan tool makes the final diagnosis.

See every step and resultShow
  1. Step 1. Is the fluid at the right level?Yes: step 2 · No: «Correct the level»
  2. Step 2. Is P0944 (pump lost prime) set too?Yes: «Follow your model's bulletin» · No: step 3
  3. Step 3. Is your transmission a CVT?Yes: «Inspect the belt» · No: step 4
  4. Step 4. Is the filter OK, not plugged or cracked, with its seal seated in the pump bore?Yes: step 5 · No: «Replace or reinstall the filter»
  5. Step 5. Measured with a gauge, does the actual line pressure match the scan tool reading?Yes: «Actual pressure is low» · No: «Pressure sensor or its circuit»

Results

  • Correct the level. Correct the level with the fluid the carmaker specifies, find the leak and test again. With low pressure, the clutches or a CVT's belt slip and get damaged further, so drive it as little as possible.
  • Follow your model's bulletin. With P0944 too, follow Chrysler's bulletin before replacing parts: on 2022–2023 Ram 2500 and 3500 trucks (US) with slow engagement on the first start, Stellantis replaces the transmission; on the 2024 with the 68RFE, a rear thrust plate; and on the 2011–2017 62TE (US), with P0740, it was a cracked converter piston.
  • Inspect the belt. On Nissan CVTs, Nissan removes the valve body and inspects the belt: if it slipped, it replaces the CVT; if not, only the valve body. If every pressure reads low, the rebuilding industry suspects the pump flow control valve.
  • Replace or reinstall the filter. A plugged, cracked or misinstalled filter lowers pressure: replace it or install it with the seal in the pump bore, correct the level and test again.
  • Actual pressure is low. If the gauge confirms low pressure, check that the main regulator valve isn't sticking in the valve body: Chrysler ends at the pump when everything else checks good. Don't keep driving it: the clutches slip and get damaged further.
  • Pressure sensor or its circuit. If the gauge doesn't match the scan tool, the actual pressure isn't what the computer reads: check the line pressure sensor and its circuit before opening the transmission.
Diagnostic tip

Measure line pressure with a gauge and compare it with the scan tool reading: on the 545RFE, Chrysler expects actual within ±5 psi of desired in D and R; on the 62TE, with the gauge on the L/R port, within 5 psi. If it sets with P0944 on a Ram HD, follow Chrysler's bulletin before replacing the converter or internal parts.

Can I drive with this code?

Better not to keep driving: with low pressure the clutches or the CVT belt slip and get damaged further. Get it to the shop with as few miles as possible.

What carmaker bulletins say53 carmaker bulletins and the vehicles they nameShow

53 service bulletins published by the US NHTSA mention this code, mostly from RAM, Nissan, Kia, Ford, Hyundai (2016–2024 models). The repair they mention most: updating the computer software.

Vehicles with service bulletins for this code

  • RAM 3500 2016–2024
  • RAM 2500 2016–2024
  • Kia K5 2021–2023
  • Kia Sorento 2021–2023
  • Nissan Sentra 2018–2019
  • Nissan Versa Note 2018–2019
  • Hyundai Sonata 2021–2022
  • Hyundai Santa Cruz 2023
Bulletin 9100202 · 2023
RAM 2500 2023 · RAM 3500 2023

Pump assembly and reaction shaft: if DTCs P0944 and P0868 are present, do not replace the torque converter or internal transmission parts; see publication S2321000007.

Open the bulletin (PDF) ↗
Bulletin S2321000007 · 2023
RAM 2500 2022–2023 · RAM 3500 2022–2023

MIL on with DTCs P0944 (loss of hydraulic pump prime) and P0868 (transmission fluid pressure low).

Open the bulletin (PDF), page 1 ↗
Bulletin 23-AT-004H · 2023
Hyundai Sonata 2021–2022 · Hyundai Santa Cruz 2023 · Hyundai Santa Fe 2021–2022

Only if Recall 236 or Service Campaign T8N was done: replace the 8-speed wet dual-clutch transmission for high-pressure electric oil pump DTCs (P1C2D03, P193B79, P0868).

Open the bulletin (PDF), page 4 ↗

These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.

TSS parts for the transmissions in these bulletins

Buy in

Different transmission? Pick it and we'll show its parts:

See parts →

Find the part by its number on the exploded diagram: 45RFE

Related codes

← See all codes

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.