Code P0702: Transmission control system electrical
The transmission computer found a fault and asks the engine computer to turn on the check engine light. This code is almost never alone: it's a sign that another code is stored in the transmission module.
Transmission control system
System voltage low, high or out of range
Only as far as the shop
What car do you have?
Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.
Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →
Symptoms
- Check engine or transmission light on
- It often sets together with other transmission-computer voltage codes, such as P0882 or P0883
- Shift problems that come and go, depending on the unit
Most common causes
- 1System voltage low, high or out of rangeOn the 2012 Focus PowerShift (DPS6) (US), Ford says P0702 can set with P0882, P0883 and P1397 if voltage is out of range during the self-test.
- 2The battery, the alternator, or their terminals and grounds
- 3The transmission computer's power feedIts fuse, wiring and connector.
- 4The transmission computer, last
From most common and easiest to check to least common.
Follow these steps
Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.
Reading the transmission module, are there also voltage codes, such as P0882 or P0883?
You need a scan tool that reaches the transmission module. On the 2012 Focus PowerShift (DPS6) (US), Ford says P0702 can set with P0882, P0883 and P1397 if voltage is out of range during the self-test.
It's guidance: a technician with a scan tool makes the final diagnosis.
See every step and resultShow
- Step 1. Reading the transmission module, are there also voltage codes, such as P0882 or P0883?Yes: «Fix the voltage codes first» · No: step 2
- Step 2. Are the battery and alternator output OK, with clean, tight terminals and grounds?Yes: step 3 · No: «Battery or alternator»
- Step 3. With the key ON, is the right voltage reaching the transmission computer's connector?Yes: step 5 · No: step 4
- Step 4. Is the fuse that feeds the transmission computer good?Yes: «Power-feed wires or connector» · No: «Replace the fuse»
- Step 5. Is there a software update for your VIN?Yes: «Update the software» · No: «The transmission computer, last»
Results
- Fix the voltage codes first. Repair the voltage codes first: they have their own page in this tool. Start with the battery, the alternator output and their terminals and grounds, then clear the codes and test again.
- Battery or alternator. Low, high or out-of-range voltage sets this code. Charge or replace the battery, fix the alternator output and clean the terminals and grounds, then clear the codes and test again.
- Replace the fuse. Replace the fuse that feeds the transmission computer, clear the codes and measure the voltage at its connector again.
- Power-feed wires or connector. If the fuse is good and the voltage isn't getting through, repair the wires or connector that feed the transmission computer before replacing it.
- Update the software. Ask the dealer for the reflash for your VIN and read the codes again afterwards.
- The transmission computer, last. With the battery, alternator, fuse, wires and connector voltage OK, the transmission computer is the suspect. Replace it only when the diagnosis confirms it, and it almost always needs programming.
Check the battery and alternator output first, then measure voltage at the transmission computer connector: on the Focus DPS6, Ford wants more than 10.5 V and checks the fuse that feeds it. If there are voltage codes (P0882, P0883), fix those first.
Only as far as the shop: a power-feed fault can make the transmission act up intermittently or go into limp mode.
TSS parts for this code
Pick your transmission to see the TSS parts that fit it, or open all parts of this type:
Buying wholesale or own a parts store?
We'll send you a quote or tell you how to sell TSS in your area.