Service shifter message and lever stuck in 'P', with DTCs such as U0101, U0103 or U0418. Check valve body CAN terminals for corrosion, ESM-TCM wiring and voltage, and bent pins.
Open the bulletin (PDF), page 1 ↗Code U0101: Lost communication with TCM
A module stopped talking to the others over the vehicle network (CAN), or the whole network went down. It's almost always power, grounds, connectors or network wiring, not the module.
Module communication
Battery and charging system
It depends on the vehicle
What car do you have?
Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.
Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →
Symptoms
- The transmission stays in one gear or won't shift2nd on the Silverado and Sierra with the 6L80, 3rd on the 2021 Charger, Challenger and 300 with the 3.6.
- The car won't start or won't come out of Park (2016–2017 Civic CVT, 2017–2020 F-150)
- Loss of drive or power with the gear letter flashing on the dash (Focus and Fiesta PowerShift)
- Check engine light, service messages that come and go and gauges that move on their own (2015–2020 Trax)
Most common causes
- 1Battery and charging systemFord says to fix any low voltage before replacing the PowerShift module.
- 2Fuses and module powerGM checks the fuse block for loose or damaged terminals.
- 3GroundsGM asks to check the transmission module ground; on the 2015–2020 Trax it was ground G103, in front of the battery.
- 4Connectors and harnessBacked-out or wet terminals at the 6L80's 16-way connector, the 6T40 connector terminals, a harness chafed on top of the transmission or poorly secured (2017–2020 F-150).
- 5SoftwareFCA fixed the 2021 Charger by reprogramming the engine computer, and GM reprogrammed the transmission module on the 2023 Equinox and Silverado.
- 6Last, the moduleA wrong or used module, or an internal failure like the one Honda found on the 2016–2017 Civic CVT.
From most common and easiest to check to least common.
Follow these steps
Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.
Are the battery and charging system OK?
Ford asks to fix any low voltage before replacing the PowerShift module.
It's guidance: a technician with a scan tool makes the final diagnosis.
See every step and resultShow
- Step 1. Are the battery and charging system OK?Yes: step 2 · No: «Battery first»
- Step 2. After clearing the codes, does U0101 come back?Yes: step 3 · No: «It was only in history»
- Step 3. Do several modules show U codes, not just U0101?Yes: «It points to the network or the power supply» · No: step 4
- Step 4. Are the transmission module's fuses, power supply and grounds OK?Yes: step 5 · No: «Fuses, power supply or grounds»
- Step 5. Are the module and transmission connectors clean and tight, with no pushed-out terminals, water or chafed harness?Yes: step 6 · No: «Connector or harness»
- Step 6. Is there a software update for your VIN?Yes: «Update the software» · No: «Now the module»
Results
- Battery first. Charge or replace the battery and fix terminals, cables and grounds, then clear the codes and test again. Ford asks to fix any low voltage before replacing a module.
- It was only in history. GM asks not to replace a module for a U code that's only in history: a low battery or a module unplugged with the car on also leaves one.
- It points to the network or the power supply. If several modules show U codes, the problem isn't the transmission module. At the shop, with the ignition off, measure the network between terminals 6 and 14 of the diagnostic connector: about 60 Ω (GM accepts 50 to 70); 35 to 50 can mean an extra resistor, for example from the wrong module.
- Fuses, power supply or grounds. Repair the module's power supply or ground. On the 2015–2020 Trax, GM found ground G103, in front of the battery.
- Connector or harness. Repair pushed-out or wet terminals and the chafed harness: GM documented it at the 16-way connector of the 6L80 and at the 6T40's connector, and on the 2017–2020 F-150 it was a poorly secured harness on top of the transmission.
- Update the software. Ask for the reflash for your VIN: FCA fixed it by reprogramming the engine computer on the 2021 Charger, and GM reprogrammed the transmission module on the 2023 Equinox and Silverado.
- Now the module. With every circuit OK, GM replaces the module that doesn't communicate, and then it has to be programmed and the adaptive learning done. Watch out for a wrong or used module.
Read the codes in every module and note which ones store U0101 and whether the scan tool can reach the transmission module. If several modules set it along with other U codes, suspect the network or power supply, not the module. GM wants under 10 Ω on each module ground and says not to replace a module for a U code that is only in history.
It depends on the vehicle: it may stay in one gear or not restart. Drive it carefully straight to the shop, and if it won't leave Park or won't start, don't keep trying.
What carmaker bulletins say93 carmaker bulletins and the vehicles they nameShow
93 service bulletins published by the US NHTSA mention this code, mostly from Chevrolet, GMC, Cadillac, RAM, Audi (1989–2025 models).
Vehicles with service bulletins for this code
- GMC Sierra 1500 2007–2021
- Chevrolet Silverado 1500 2007–2021
- Cadillac Escalade 2007–2020
- GMC Yukon 2007–2020
- Chevrolet Tahoe 2007–2020
- RAM 3500 2019–2020
- RAM 4500 2019–2020
- Audi A6 2012–2019
Information for when DTC U010100 (lost communication with TCM, diagnostic address 23) occurs.
Open the bulletin (PDF) ↗These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.
Buying wholesale or own a parts store?
We'll send you a quote or tell you how to sell TSS in your area.
