New ECM reprogramming files for crank/cam correlation (P0016–P0019), cam timing (P0011, P0012), EVAP (P2404) and U0100 DTCs.
Open the bulletin (PDF), page 2 ↗Code U0100: Lost communication with ECM/PCM
A module stopped talking to the others over the vehicle network (CAN), or the whole network went down. It's almost always power, grounds, connectors or network wiring, not the module.
Module communication
A weak battery, loose terminals or low voltage
Carefully and only to the shop
What car do you have?
Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.
Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →
Symptoms
- The transmission stays in one gearGM says a U0100 in the transmission module sends it to its default gears, because it no longer gets engine speed, load and throttle data.
- Check engine light plus several warning lights or messages at once, which may come and go
- The engine may not start or may stall if the engine computer loses power or the high-speed network fails completely (GM)
- The same code stored in several modules (transmission, ABS, cluster) at the same time
Most common causes
- 1A weak battery, loose terminals or low voltageNissan warns low voltage can set CAN network codes.
- 2Fuses or power feed to the engine computerIf U0100 shows up in several modules, the engine computer stopped talking to all of them.
- 3A bad groundOn the 2015–2020 Trax, GM found ground G103, in front of the battery (bulletin that includes Latin American countries).
- 4Corroded, wet or backed-out connector terminals, at the engine computer or at the module that stores the code (GM documented this at the 6L80 connector)
- 5A chafed harness or an add-on device badly wired into the network, such as an aftermarket radio or navigation unit (GM)
- 6Software and, last, the engine computer itself, only once the circuits test good
From most common and easiest to check to least common.
Follow these steps
Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.
Are the battery and alternator OK, with tight terminals, cables and grounds?
With low voltage, modules go silent one by one: Nissan mentions under 10 V.
It's guidance: a technician with a scan tool makes the final diagnosis.
See every step and resultShow
- Step 1. Are the battery and alternator OK, with tight terminals, cables and grounds?Yes: step 2 · No: «Battery first»
- Step 2. After clearing the codes and running the engine for 10 seconds, does U0100 come back?Yes: step 3 · No: «It was only in history»
- Step 3. Do several modules store U0100?Yes: step 4 · No: «Only one module stores it»
- Step 4. Does the engine computer respond to the scan tool?Yes: step 5 · No: «The engine computer doesn't respond»
- Step 5. At the shop, with the ignition off, do you measure about 60 Ω between pins 6 and 14 of the diagnostic (OBD) connector?Yes: step 6 · No: «Network fault»
- Step 6. Are there aftermarket accessories (radio, navigation, GPS tracker) or water in the connectors?Yes: «Accessory or water» · No: «Software, and the module last»
Results
- Battery first. Charge or replace the battery and fix terminals, cables and grounds, then clear the codes and test again. Ford asks to fix any low voltage before replacing a module.
- It was only in history. A U code left only in history can come from a battery event, and GM asks not to replace a module for that. If it comes back, return to this diagnosis.
- Only one module stores it. Check the wiring and connector between that module and the network, and look for bulletins: it may be a known false code.
- The engine computer doesn't respond. It's off or isolated: check its fuses, the main relay, the grounds (GM asks for under 10 Ω and Toyota under 1 Ω at the computer ground) and the wake-up wire. On the 2015–2020 Trax, GM found ground G103, in front of the battery.
- Network fault. About 120 Ω: one end is missing (an open wire or a connector). Close to 0 Ω: the lines are shorted; unplug modules one by one until the reading changes. 35 to 50 Ω (GM): there's an extra resistor, for example from the wrong module.
- Accessory or water. Remove the poorly installed accessory, or dry and repair the connector: radios, GPS trackers and poorly installed harnesses appear in GM, Toyota and Chrysler bulletins.
- Software, and the module last. Look for reflashes for your VIN: many cases were fixed that way. If everything above checks out, the module is replaced and programmed, and then the codes are cleared in every module.
If only one module stores U0100, check the wiring and connector between that module and the network; if several do, check the engine computer's power and grounds. With the ignition off, about 60 Ω across pins 6 and 14 of the diagnostic connector is normal (GM accepts 50–70); that value doesn't apply the same way to every vehicle.
Carefully and only to the shop: depending on the vehicle, the transmission stays in one gear and the engine may not restart.
What carmaker bulletins say135 carmaker bulletins and the vehicles they nameShow
135 service bulletins published by the US NHTSA mention this code, mostly from Chevrolet, GMC, Cadillac, Jeep, RAM (1989–2024 models). The repair they mention most: updating the computer software.
Vehicles with service bulletins for this code
- Chevrolet Silverado 1500 2007–2022
- GMC Sierra 1500 2014–2022
- Chevrolet Tahoe 2007–2020
- GMC Yukon 2007–2020
- Cadillac Escalade 2007–2020
- RAM 3500 2013–2015
- RAM 2500 2013–2015
- Jeep Renegade 2019–2022
New ECM reprogramming files for crank/cam correlation (P0016–P0019), cam timing (P0011, P0012), EVAP (P2404) and U0100 DTCs.
Open the bulletin (PDF), page 2 ↗These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.
Buying wholesale or own a parts store?
We'll send you a quote or tell you how to sell TSS in your area.
