Code P0785: Shift/timing solenoid malfunction
The computer commanded a shift that didn't happen as expected, or the shift timing solenoid fails. It can be a solenoid, the valve body, pressure or a clutch.
Shift error
The solenoid connector or wiring
It can be driven carefully to the shop
What car do you have?
Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.
Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →
Symptoms
- Harsh or mistimed downshifts, especially 3-2, on units that use a 3-2 solenoid
- Check engine light on
- Limp mode on some units, such as the VW 01M, which holds 3rd with solenoid faults
Most common causes
- 1The solenoid connector or wiringOpen, shorted, wet or corroded.
- 2The transmission's internal harness
- 3The shift/timing solenoidOn the 4L60E it's the 3-2 solenoid (GM used P0785 from 1997 to 2007; before that it was P1886); on the VW 01M, N94, per a VW table.
- 4The computer, last
From most common and easiest to check to least common.
Follow these steps
Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.
Are P0740, P0753, P0758 or P1860 set too?
On the 4L60E, those solenoids share the 3-2 solenoid's fuse.
It's guidance: a technician with a scan tool makes the final diagnosis.
See every step and resultShow
- Step 1. Are P0740, P0753, P0758 or P1860 set too?Yes: «Fuse and power feed first» · No: step 2
- Step 2. Was the pan removed or the valve body worked on just before the code appeared?Yes: «Check that it was plugged back in» · No: step 3
- Step 3. When you cycle the solenoid with the scan tool three times, can you hear it click at the pan?Yes: «Intermittent fault or loose connector» · No: step 4
- Step 4. At the transmission connector, on the engine harness side, is there power, and does a test lamp turn on and off with the scan tool?Yes: step 5 · No: «Power feed or control wire»
- Step 5. On the transmission side, does the internal harness with the solenoid measure within the manual's value, with no short to ground?Yes: «Wiring, and the computer last» · No: step 6
- Step 6. With the pan off, does the solenoid alone measure correctly, with no short to ground?Yes: «Replace the internal harness» · No: «Replace the solenoid»
Results
- Fuse and power feed first. First check the fuse and power feed they share: GM tests each of those solenoids for a short to ground. Then clear the codes and test again.
- Check that it was plugged back in. If the code appeared right after the pan came off or the valve body was worked on, first check that the 3-2 solenoid was plugged back in: unplugged, the circuit is open.
- Intermittent fault or loose connector. If it clicks, GM looks for an intermittent fault or a loose connector: check the transmission connector and its terminals, clear the code and test again.
- Power feed or control wire. If there's no power, check the fuse and power feed. If the control wire fails, repair the short to ground, open or short to power between the computer and the transmission before touching the solenoid.
- Wiring, and the computer last. With the power feed, control wire, internal harness and solenoid OK, check the wiring between the computer and the transmission: GM only replaces the computer after all those tests, and on the Aveo it also comes last. On the 01M, if the wires measure 1.5 Ω or less, VW replaces the circuit board or the valve body.
- Replace the internal harness. If the solenoid alone measures correctly with no short to ground, GM replaces the 4L60E's internal harness, not the solenoid. With the pan off, replace the filter and check the fluid.
- Replace the solenoid. If the solenoid alone measures out of range, replace it: on the 4L60E it's the 3-2 solenoid, and on the Aveo, the timing solenoid. First confirm your transmission has one: per the rebuilding industry, most 2009-and-later 4L60Es no longer use a 3-2 solenoid.
Confirm your transmission has that solenoid: per the rebuilding industry, most 2009-and-later 4L60Es no longer use a 3-2 solenoid. Measure its coil and circuit from the case connector before replacing it.
It can be driven carefully to the shop: avoid flooring it to force downshifts until it's fixed.
TSS parts for this code
Pick your transmission to see the TSS parts that fit it, or open all parts of this type:
Buying wholesale or own a parts store?
We'll send you a quote or tell you how to sell TSS in your area.