Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

Code P0785: 3-2 shift solenoid on Silverado and Aveo

TSS editorial team · · 10 min read

Technician plugging an OBD2 diagnostic scanner beneath a steering column to troubleshoot code P0785
In short
  • P0785 is an electrical fault: the solenoid circuit doesn't respond to the computer's command (open, shorted to ground or shorted to power). The "timing" in its name is shift timing, not engine timing.
  • In Mexico it's set by GM trucks with the 4L60E up to 2007 (Silverado, Cheyenne, Suburban, Tahoe, Avalanche, TrailBlazer, Colorado, Yukon and Escalade), the automatic Aveo 1.6 and the automatic Jetta A4 with the 01M.
  • On the 4L60E, the computer leaves the transmission in 3rd, raises line pressure to maximum and stops converter lockup.
  • GM's test: the 3-2 solenoid measures 20 to 32 Ω and more than 250 kΩ to ground. If it tests good, GM replaces the internal harness, not the solenoid; the computer comes last.
  • From 2008, GM reports the same solenoid as P0787 and P0788. No US bulletin or recall mentions P0785.

In Mexico, code P0785 shows up mostly on Chevrolet and GMC trucks with the 4L60E and on the automatic Aveo. Much of what's out there confuses it with engine timing or with the fluid. In GM's manuals it's something else: an electrical fault in the circuit of the solenoid that controls the 3-2 downshift. This guide pulls together what GM and VW manuals say: what it means on each unit, which vehicles set it in Mexico, what the transmission does, how it's tested and which TSS parts fit. If you have another code, look it up in our diagnosis by code.

What does code P0785 mean?

By the standard, P0785 is "shift/timing solenoid": the timing is when the shift happens, not engine timing. Each maker uses it its own way:

GM 4L60E, 4L65E and 4L70E, 1997 to 2007 (trucks and SUVs)3-2 shift solenoid circuit. It's an on/off solenoid bolted to the valve body that times the 3-4 clutch release against the 2-4 band apply on the 3-2 downshift
GM 4L60E, 2008 onNot used anymore: the same solenoid sets P0787 (low voltage) and P0788 (high voltage)
GM 4L60E, 1993 to 1995, before OBD-IIThere's no P0785: the 3-2 solenoid was duty-cycle (PWM) controlled, and its fault was code 66
Chevrolet Aveo 1.6 automatic (Aisin AW81-40LE)Timing solenoid circuit. GM's 2008 manual diagnoses it together with P1710; in GM's 2009 and 2010 diagnostic sheets, the same solenoid shows up as P0787 and P0788
VW 01M (Jetta A4 automatic)"Shift/Timing Solenoid" (VW code 17169). The manual doesn't say which one: it sends you to check every valve body solenoid
GM 4T40E, 4T45E, 4T65E and 5L40EThey don't use it, per GM's diagnostic sheets
Toyota, Nissan, Honda, Hyundai, Kia, Mazda, Mitsubishi, Suzuki, Ford and ChryslerIt isn't in the code lists of the models we checked. Toyota uses P0787 and P0788 for its ST shift/timing solenoid (U340E and U341E)

The same number can point to different parts: on the 4L60E it's the 3-2 solenoid; on the Aveo, the timing solenoid; and on the Jetta, any of the seven on the valve body. And the same 4L60E solenoid changes codes with the model year.

Which vehicles set it in Mexico?

Silverado, Cheyenne and Suburban 1500, up to 2007Yes: 4L60E
Avalanche, TrailBlazer, Tahoe, Colorado and Express, up to 2007Yes: 4L60E
2007 GMC Yukon and Canyon, and 2002 to 2006 Cadillac EscaladeYes: 4L60E; the AWD Escalade, 4L65E
2008-on GM trucks with the 4L60E (Silverado, Cheyenne, Tahoe, Yukon, Sierra, Colorado, Canyon, H3)No: the same solenoid sets P0787 and P0788, and some 2009 and 2010 GM lists no longer show it
1993 to 1995 GM trucksNo: before OBD-II, the 3-2 solenoid set code 66
Aveo 1.6 automatic, 2008 to 2018Yes, per GM's 2008 manual (together with P1710); other years may set P0787 or P0788
Jetta A4 automatic, up to 2007Yes: 01M
Jetta Clásico, 2008 onA different unit: the 6-speed Tiptronic 09G, whose code list we didn't check
Malibu, Impala, Venture, Uplander, Grand Am, Grand Prix and 2005 to 2008 EquinoxNo: their units (4T40E, 4T45E, 4T65E and AF33-5) don't use P0785

On the 1996 and 1997 trucks with the 5.7 TBI engine sold in Mexico, we didn't confirm whether the computer uses OBD-II codes. If your GM is front-wheel drive, its problems are in our 4T40E and 4T45E and 4T65E guides; and if you don't know which transmission it has, see which transmission does my Chevrolet have or the GMC, Buick and Cadillac guide.

What does the transmission do with P0785?

On the 4L60E, the computer protects the transmission: it lets it "soft land" in 3rd, raises line pressure to maximum, stops converter lockup and freezes its adapts. So what the driver usually notices is a 3rd-gear start, no overdrive, firm shifts and higher engine rpm on the highway. We infer that from what the computer does; GM's 1995 manual does write it that way for code 66: "Third gear starts".

In the 2003 and 2005 manuals, the check engine light comes on during the second consecutive trip with the fault (in other GM sheets, on the first) and goes off after 3 consecutive trips without it. The transmission returns to normal when the fault goes away or the computer powers down, but if you clear the code without a repair, it comes back.

On 2008 trucks the reaction is milder: with P0787, the transmission holds off the 3-2 downshift until it slows to about 20 km/h (12 mph); with P0788, it only freezes its adapts.

On the Aveo, GM's manual turns on the check light from the first ignition cycle with the fault (on versions for other markets, the HOLD light) and the computer goes into "emergency mode"; a 2010 GM sheet adds that in that mode it turns off every solenoid. We didn't confirm which gear the Mexican Aveo stays in or which light it uses.

How does GM diagnose it on the 4L60E?

This is the order in GM's service manuals for the 2003 Silverado and the 2005 TrailBlazer:

  • Read every code and save the freeze frame before clearing.
  • If P0740, P0753, P0758 or P1860 are also set, check the fuse and the feed first: those solenoids share the 3-2 solenoid's fuse, and GM tests each one for a short to ground.
  • With the scan tool, command the 3-2 solenoid on and off three times and listen for the click at the pan with a stethoscope. If it clicks, look for an intermittent fault or a loose connector.
  • At the transmission connector, on the engine harness side, there should be power, and a test lamp between the feed and the control circuit should turn on and off with the scan tool. If it stays on, the control circuit is shorted to ground; if it never lights, it's open or shorted to power.
  • On the transmission side, measure the internal harness with the solenoid: 20 to 32 Ω across the two terminals, and more than 250 kΩ from each one to ground.
  • Drop the pan and measure the solenoid alone. If it reads 20 to 32 Ω with no short to ground, GM replaces the internal harness; if it's out of range, it replaces the 3-2 solenoid.
  • Last, the wiring between the computer and the transmission. GM only replaces the computer after all those tests.

GM gives no temperature for the 20 to 32 Ω, and at no step does it replace the valve body for this code. If the code showed up right after dropping the pan or working on the valve body, first check that the 3-2 solenoid was plugged back in: unplugged, the circuit reads open.

On 1993 to 1995 trucks, the 3-2 solenoid was duty-cycle controlled and measured 9 to 14 Ω; GM tested it with the scan tool at 0 % and 100 %, and if it was out of range, replaced the solenoid or the internal harness. On 2008 trucks (P0787 and P0788), GM first rules out P0961, P0973, P0976, P2764 and P2769, checks the TRANS fuse and uses the same values: 20 to 32 Ω, and more than 250 kΩ to the case. More problems with this unit are in our 4L60E guide.

P0785 on the Aveo and the Jetta A4

On the 2008 Aveo, GM diagnoses P0785 together with P1710, "timing solenoid circuit". Measure the harness with the solenoid from the transmission computer connector, then the solenoid to ground from the transaxle connector: both should read 11 to 16 Ω at 20 °C (68 °F). Depending on what you find, the connector or harness is repaired or the solenoid replaced; the computer comes last, once the harness and connections check good. More Aveo problems are in our Aveo and Optra guide.

On the Jetta A4 with the 01M, VW's 2005 manual lists P0785 as "Shift/Timing Solenoid" and sends you to check every valve body solenoid. With the ignition off and the lever in P, check the transmission connector for corrosion and water; then, at about 20 °C (68 °F), the on/off solenoids (N88, N89, N90, N92 and N94) should read 55 to 65 Ω, and the modulating ones (N91 and N93), 4.5 to 6.5 Ω; resistance goes up when the transmission is hot. Each wire between the computer and the connector should read 1.5 Ω or less. If the wires are good, VW replaces the circuit board or the valve body.

Are there bulletins on P0785?

No US NHTSA technical bulletin or recall from 1995 to 2024 mentions P0785 or the 3-2 solenoid. The closest one is GM bulletin 01-07-30-042H (January 2014), for 2014 and earlier 4L60E, 4L65E and 4L70E units: a clunk on the 2-3 upshift or the 3-2 downshift, more noticeable on 4x4s, "is a normal condition", and GM says no repairs should be attempted. In other words, a clunk on that shift doesn't mean the 3-2 solenoid is bad. These are US documents; we found no GM campaigns in Mexico for this code.

P0785 myths

  • "P0785 is an engine timing problem." The timing is shift timing. The "timing solenoid" bulletins you'll find online are for engine variable valve timing and have other codes.
  • "The most common cause is low or dirty fluid." GM sets P0785 only when the circuit voltage doesn't match the computer's command. Its causes are the wiring, the solenoid, the computer and the shared fuse; fluid isn't on its list.
  • "P0785 is shift solenoid B." On the 4L60E, B is the 2-3 solenoid, with its own codes (P0756 to P0758, and P0976 and P0977 from 2008); see our shift solenoid guide. The 3-2 solenoid is a separate part.
  • "Replace the solenoid and you're done." GM measures it first: if it reads 20 to 32 Ω with no short to ground, it replaces the internal harness, not the solenoid.
  • "Any 3-2 solenoid will do." The 1993 to 1995 one was duty-cycle controlled and measured 9 to 14 Ω; the 1996-on one is on/off and measures 20 to 32 Ω. On the Aveo, the timing solenoid measures 11 to 16 Ω.
  • "A clunk on the 3-2 downshift means the 3-2 solenoid is bad." GM says that clunk can be normal and that no repairs should be attempted; P0785 is an electrical fault.
  • "A stuck 3-2 valve causes P0785." The code only monitors the electrical circuit: fuse, wires, solenoid and computer. A stuck valve can cause bad shifts, but it can't open or short the circuit.

See 4L60E parts

TSS parts for P0785

The 4L60E page has every TSS part for this unit, and the 01M page has the Jetta's. These are the ones that match the jobs in this guide:

4L60E 3-2 solenoid, 1996 onOn/off 3-2 solenoid, white connector
1993 to 1995 3-2 solenoid (PWM), per the TSS catalogPWM 3-2 solenoid
Internal harness (if the solenoid tests good)1993 to 2002, 13-pin and 2006 to 2008, with input speed sensor
Transmission external connector13-pin female connector repair kit
Filter, when the pan comes off4L60E, deep pan and Colorado and H3 filters
VW 01M (Jetta A4)7-solenoid kit, shift solenoid and modulating solenoid

TSS lists its on/off 3-2 solenoid for 1996 on and the PWM one for 1993 to 1995; the GM manuals we read don't give the exact changeover year, so on 1996 and 1997 units confirm with your distributor which one yours uses, or compare it with the one you took out. The TSS catalog has no part for the Aveo's timing solenoid; it does have gasket kits and friction plates for the AW81-40LE. To test other solenoids, see our transmission solenoid guide.

TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • What does code P0785 mean?

    By the standard it's "shift/timing solenoid", and the timing is shift timing, not engine timing. On 1997 to 2007 GM trucks with the 4L60E it's an electrical fault in the 3-2 solenoid circuit; on the automatic Aveo, in the timing solenoid circuit; and on the Jetta A4, in one of the valve body solenoids.

  • Can I drive with code P0785?

    On the 4L60E, the computer leaves the transmission in 3rd, with line pressure at maximum and no converter lockup, to protect it. It's a limp mode, not for everyday use: get it checked.

  • What should the 4L60E 3-2 solenoid measure?

    Per GM, 20 to 32 Ω, and more than 250 kΩ from each terminal to ground. The 1993 to 1995 one, which was duty-cycle (PWM) controlled, measured 9 to 14 Ω.

  • If the solenoid tests good, what's next?

    GM replaces the transmission's internal harness. Before that, check the fuse, the connector and the wires to the computer; the computer comes last.

  • Why does my Aveo set P0785?

    On the automatic Aveo 1.6, GM uses that code for the timing solenoid circuit, together with P1710. It should read 11 to 16 Ω at 20 °C (68 °F); check the connector, harness and solenoid before the computer.

  • What's the difference between P0785, P0787 and P0788?

    On the 4L60E it's the same 3-2 solenoid: GM used P0785 from 1997 to 2007, and in 2008, P0787 (low voltage) and P0788 (high voltage), with a milder transmission reaction.

  • Does the fluid have anything to do with P0785?

    Not directly: GM sets it only for an electrical fault in the circuit. If you drop the pan to replace the solenoid or the harness, it's a good time to change the filter and check the fluid.

  • Is there a campaign or warranty for P0785?

    We found none: no US bulletin or recall mentions it, and we found no campaigns in Mexico either.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.