MIL on with one or a combination of DTCs P0740, P0744, P0840 or P1777. Follow the bulletin's repair flow chart.
Code P1777: Nissan CVT: stepper motor circuit
Nissan CVT-specific codes: belt slip, judder or the stepper motor that moves the pulleys. Nissan handles them with software updates, the valve body or a whole CVT.
Nissan CVT
The step motor circuit
It can be driven carefully to the shop, but if the CVT isn't changing ratio properly, avoid highway driving and steep hills
What car do you have?
Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.
Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →
Symptoms
- Check engine light on Nissan JF011E CVTs (Sentra, X-Trail, Altima, Rogue) and on the Jeep Compass and Patriot, Dodge Caliber and Mitsubishi models with the same unit
- It may pull away slowly or weaklyThe step motor is what changes the CVT ratio.
- It can set together with P0840, P0845 or P0744
Most common causes
- 1The step motor circuitWire, connector or the motor winding (Nissan calls it "step motor circuit").
- 2The valve bodyThe step motor is mounted on it, and on the 2007–2008 Altima, Rogue and Sentra (US), Nissan replaced the whole valve body for P0840, P0845, P0744 or P1777.
- 3Module calibrationAfter replacing the valve body, Nissan erases the calibration data stored in the module so it recalibrates.
- 4The step motor itself, after ruling out the wiring
From most common and easiest to check to least common.
Follow these steps
Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.
Does your CVT have a step motor (JF009E, JF010E or JF011E)?
It's on, for example, the 2007–2012 Sentra, 2008–2014 X-Trail, 2007–2012 Altima and the Jeep Compass and Patriot with the CVT. The 2013-on Sentra, 2015-on X-Trail, Kicks and Pathfinder don't have one.
It's guidance: a technician with a scan tool makes the final diagnosis.
See every step and resultShow
- Step 1. Does your CVT have a step motor (JF009E, JF010E or JF011E)?Yes: step 2 · No: «That CVT has no step motor»
- Step 2. Checked hot, is the fluid at the right level, with no leaks and in good condition?Yes: step 3 · No: «Check the fluid»
- Step 3. Are there communication (U1000) or speed sensor (P0715, P0720) codes?Yes: «Fix those codes first» · No: step 4
- Step 4. Are P0744, P0840 or P0845 set too?Yes: «Valve body» · No: step 5
- Step 5. With the key off and the CVT connector unplugged, do the coils measure about 30 Ω between terminals 6 and 7 and between 8 and 9, and about 15 Ω from each to ground?Yes: step 6 · No: «Failed step motor»
- Step 6. Measured from the computer connector, do the coils give the same values?Yes: «Look for a bad contact» · No: «Harness or connector»
Results
- That CVT has no step motor. Check the scan tool or how the code was read: those CVTs have no step motor, and their ratio fault shows up as P0965 to P0967.
- Check the fluid. Correct the level and fix the leak. If the fluid is varnished, milky or full of metal dust, the CVT needs an inside inspection before replacing electrical parts.
- Fix those codes first. Fix the communication or speed sensor codes first: look them up in this tool. The computer calculates the ratio from those sensors.
- Valve body. With that combination, Nissan replaced the valve body, which includes the step motor, and erased the computer's calibration data so it relearns (2007–2008 Sentra, Altima and Rogue, US).
- Failed step motor. With the coils out of spec, the step motor failed. Nissan replaces the complete valve body, which includes it; a replacement motor changes only the failed part. When installing it, make sure the linkage is engaged with the motor.
- Harness or connector. If the coils measure good at the CVT connector but bad from the computer, the fault is in the harness or connector: repair it and don't replace the motor.
- Look for a bad contact. If everything measures good, move the harness and connectors with the scan tool connected to find a bad contact. Then clear the code and do the manual's road test to confirm it doesn't come back.
It's the step motor's electrical code (P1778 is the functional one). Check the connector and wiring first; if you replace the valve body, erase the module's calibration data as Nissan asks.
It can be driven carefully to the shop, but if the CVT isn't changing ratio properly, avoid highway driving and steep hills.
What carmaker bulletins say2 carmaker bulletins and the vehicles they nameShow
2 service bulletins published by the US NHTSA mention this code, mostly from Nissan (2007–2010 models).
Vehicles with service bulletins for this code
- Nissan Sentra 2007–2008
- Nissan Altima 2008
MIL on with P0840, P0845, P0744 or P1777: replace the control valve assembly with the listed part, erase the TCM EEPROM calibration data and let it recalibrate.
These are US bulletins: check with your dealer or shop whether they apply to your car.
TSS parts for this code
Pick your transmission to see the TSS parts that fit it, or open all parts of this type:
Buying wholesale or own a parts store?
We'll send you a quote or tell you how to sell TSS in your area.