Slower than normal acceleration from a stop at times and/or MIL on with P1778 (step motor). Follow the bulletin's repair flow chart.
Open the bulletin (PDF), page 3 ↗Code P1778: Nissan CVT: stepper motor function
Nissan CVT-specific codes: belt slip, judder or the stepper motor that moves the pulleys. Nissan handles them with software updates, the valve body or a whole CVT.
Nissan CVT
The valve body
It can be driven carefully to the shop, but with slow take-offs avoid merging onto fast roads or climbing steep grades with a load
What car do you have?
Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.
Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →
Symptoms
- Slower than normal take-off, especially after long highway driving (Nissan documented this on the JF011E)
- Check engine light on
- On Jeep Compass and Patriot, Dodge Caliber and Mitsubishi CVTs with the same unit, the same step motor code
Most common causes
- 1The valve bodyOn the 2010 Altima, Sentra and Rogue (US), Nissan replaced the whole valve body and reprogrammed the module, not just the step motor.
- 2The flow control valve, pulley leaks or a worn or sticking valve bodyThe rebuilding industry says these are the most common causes.
- 3On the JF010E (2010 Maxima, Murano, Altima V6, US), if diagnosis points to the speed sensors or the module, Nissan replaces the valve body instead
- 4The step motor, lastNissan sets P1778 when the electrical side checks OK but the mechanical side doesn't.
From most common and easiest to check to least common.
Follow these steps
Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.
Does your CVT have a step motor (JF009E, JF010E or JF011E)?
It's on, for example, the 2007–2012 Sentra, 2008–2014 X-Trail, 2007–2012 Altima and the Jeep Compass and Patriot with the CVT. The 2013-on Sentra, 2015-on X-Trail, Kicks and Pathfinder don't have one.
It's guidance: a technician with a scan tool makes the final diagnosis.
See every step and resultShow
- Step 1. Does your CVT have a step motor (JF009E, JF010E or JF011E)?Yes: step 2 · No: «That CVT has no step motor»
- Step 2. Checked hot, is the fluid at the right level, with no leaks and in good condition?Yes: step 3 · No: «Check the fluid»
- Step 3. Is P1777 set too?Yes: «Diagnose P1777 first» · No: step 4
- Step 4. Are there communication (U1000) or speed sensor (P0715, P0720) codes?Yes: «Fix the sensor or network first» · No: step 5
- Step 5. Measured with a gauge, is line pressure OK?Yes: «Valve body, not the motor» · No: «Low pressure: pump or leak»
Results
- That CVT has no step motor. Check the scan tool or how the code was read: those CVTs have no step motor, and their ratio fault shows up as P0965 to P0967.
- Check the fluid. Correct the level and fix the leak. If the fluid is varnished, milky or full of metal dust, the CVT needs an inside inspection before replacing parts.
- Diagnose P1777 first. With both codes, start with the electrical side: the step motor coils, the harness and the connector. Look it up in this tool and follow its diagnosis.
- Fix the sensor or network first. Fix the speed sensor circuit or the communication first. Note that on the 2010 Maxima, Murano and Altima V6 (US), if the manual calls for a speed sensor or the computer, Nissan replaces the valve body instead, and asks not to replace the transmission.
- Valve body, not the motor. With good pressure, Nissan points to an obstructed control valve or a sticking solenoid valve: on the 2010 Altima 2.5, Sentra and Rogue (US), it replaced the complete valve body and reprogrammed the computer, with its initialization. Don't replace the step motor right away.
- Low pressure: pump or leak. With low pressure or pressure codes, check the pump, pressure regulation or a leak: the rebuilding industry points to the pump flow control valve and pulley leaks.
Don't replace the step motor right away: the industry considers it one of the most over-replaced parts. Check speed sensors, pressures and the valve body; if you replace the valve body, Nissan reprograms and initializes the module.
It can be driven carefully to the shop, but with slow take-offs avoid merging onto fast roads or climbing steep grades with a load.
What carmaker bulletins say6 carmaker bulletins and the vehicles they nameShow
6 service bulletins published by the US NHTSA mention this code, mostly from Kia, Nissan, RAM (2010–2019 models). The repair they mention most: updating the computer software.
Vehicles with service bulletins for this code
- Nissan Altima 2010
- RAM 1500 2019
- Kia Forte 2011–2015
- Kia Sportage 2011–2014
- Nissan Maxima 2010
Slow acceleration from a stop and/or MIL with P1778 (step motor), or P0720 on Sentra without ABS. Replace the valve body and reprogram the TCM (includes initialization).
Open the bulletin (PDF), page 2 ↗TCM reprogramming for MIL with speed sensor DTCs (P0716, P0721, P07BF), P0733 in 4-Lo, P1DDE, P1DF3 and others.
Open the bulletin (PDF), page 3 ↗TCM reprogramming for MIL with speed sensor DTCs (P0716, P0721, P07BF), P0733 in 4-Lo, P1DDE, P1DF3 and others.
Open the bulletin (PDF), page 2 ↗These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.
TSS parts for this code
Pick your transmission to see the TSS parts that fit it, or open all parts of this type:
Buying wholesale or own a parts store?
We'll send you a quote or tell you how to sell TSS in your area.