Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

P1777 and P1778: Nissan CVT step motor codes

TSS editorial team · · 10 min read

Technician testing a Nissan CVT stepper motor with multimeter probes beside a JF011E valve body for codes P1777 and P1778
In short
  • P1777 and P1778 are codes for the step motor, the part that changes the ratio on Nissan's older Jatco CVTs (JF009E, JF010E and JF011E). P1777 is an electrical fault in the motor or its circuit; P1778 means the actual ratio isn't following the steps the computer commands.
  • In Mexico they can be set by the 2007 to 2012 Sentra, 2008 to 2014 X-Trail, 2007 to 2012 Altima, the Murano through 2014 and the 2012 to 2014 Juke. The 2013-on Sentra, 2015-on X-Trail, Kicks and Versa have no step motor.
  • Nissan says P1778 sets when the electrical side is fine but the mechanical side isn't. Its US bulletins fixed it by replacing the valve body and reprogramming the computer, never by replacing the motor alone.
  • The typical symptom is slower than normal acceleration from a stop, especially after a long highway drive. In fail-safe, the CVT freezes the ratio: it pulls away very slowly or won't gain speed.
  • Before buying the motor, measure its coils with the connector unplugged: about 30 Ω between terminals 6-7 and 8-9 of the CVT connector and about 15 Ω from each one to ground, the same value in every Nissan manual we checked.

Nissan's older CVTs change the ratio with a step motor: a four-coil electric motor, mounted on the valve body, that the transmission computer (TCM) moves step by step. Each step moves the ratio control valve, which sends pressure to or releases it from the primary pulley. P1777 and P1778 are that motor's codes. These transmissions' general failures are in our guide to Nissan CVT problems; this one covers diagnosing the two codes.

What do P1777 and P1778 mean?

This is how Nissan defines them in its service manuals:

P1777"Step motor - circuit": when it switches a coil on and off, the computer doesn't see the voltage change it expects. The causes, according to Nissan: an open or shorted harness or connector, or the motor itself
P1778"Step motor - function": there's a large difference between the motor's steps and the pulley's actual ratio. Nissan sets it when the electrical side is fine but the mechanical side isn't

On the 2010 Cube and 2013 Juke, Nissan calls P1778 "Step Motor Circuit Intermittent", but the Cube manual states that P1778 isn't caused by an electrical fault (an open or short circuit) but by a mechanical one, such as a clogged control valve or a sticking solenoid valve. To detect it, the computer compares the primary sensor's speed with the one it calculates from the secondary sensor, and the ratio it commanded with the actual one. Both codes turn on the check engine light.

Which cars can set P1777 and P1778?

Only those with a CVT that has a step motor: the Jatco JF009E, JF010E and JF011E. Nissan's newer CVTs (JF015E, JF016E and JF017E) control the ratio with a primary pressure solenoid, and these codes don't exist in their manuals. In Mexico:

2007 to 2012 SentraYes: JF011E
2008 to 2014 X-TrailYes: JF011E
2007 to 2012 AltimaYes: JF011E with the 2.5 and JF010E with the 3.5
Murano through 2014Yes: JF010E
2012 to 2014 JukeYes: JF011E. From 2015 it has the JF016E, without a step motor
Mitsubishi Lancer 2.0 and 2.4 and Outlander 2.4 through 2015, and 2013 and 2014 ASXYes: the same JF011E, which Mitsubishi calls F1CJA. Check Mitsubishi's service information for the code it uses
2007 to 2013 Jeep Compass, 2008 to 2013 Patriot and 2007 to 2012 Dodge CaliberYes: the same JF011E, but according to 2007 service information, Jeep and Dodge report the step motor with P1729 and an incorrect ratio with P0730
2013-on Sentra, 2015-on X-Trail, 2013-on Altima, Kicks, 2020-on Versa and Pathfinder with a CVTNo: their CVTs control the ratio with a pressure solenoid; the equivalent fault shows up as P0965, P0966 or P0967
2012 to 2019 Versa, Tiida and March automaticsNo: they're 4-speed automatics, not CVTs

More on each model's transmission in our guides to which transmission your Nissan has, the Jeep, Dodge and Mitsubishi CVT and which transmission your Mitsubishi has.

P1777 and P1778 symptoms

  • Check engine light on: both codes turn it on.
  • Slower than normal acceleration from a stop, at times. According to Nissan's bulletins, it happens more often after the car has been driven a long time on the highway.
  • It pulls away very slowly and struggles to accelerate: the CVT got stuck in a tall ratio.
  • It revs but won't gain speed: it got stuck in a short ratio.
  • It feels like slipping, because in fail-safe the computer doesn't lock the converter.

What the transmission does in fail-safe: according to Nissan, it switches off all four motor coils to hold the ratio it had right before the fault. On the Juke and Cube, if the fault comes with the car stopped, the ratio stays short and the car won't gain speed; if it comes while driving, it stays tall and pulls away slowly. Either way it doesn't lock the converter.

What causes P1777 and P1778?

P1777 is electrical: the harness or connector between the computer and the CVT (open, shorted or with loose terminals), or an open or shorted motor coil. On the Juke, Nissan also checks the internal harness that runs from the CVT connector to the valve body.

With P1778, the motor usually isn't the cause. According to the rebuilding industry, the step motor is one of the most needlessly replaced parts on these CVTs, and the most common causes of P1778 are a worn pump flow control valve, pulley leaks and a worn or sticking valve body. Since the computer works out the ratio from the speed sensors, a sensor fault can also end up as P1778.

Nissan's bulletins

Nissan published these US bulletins with P1777 and P1778 on the JF011E and JF010E CVTs:

NTB09-148: 2007 and 2008 Sentra, Altima and RogueP1777 with P0840, P0845 or P0744: replace the valve body and erase the computer's calibration data so it relearns
NTB10-150a: 2010 Altima 2.5, Sentra and RogueP1778 (a Sentra without ABS may store P0720): replace the valve body and reprogram the computer, with its initialization
NTB11-002c: 2010 Maxima, Murano and Altima V6P1778: diagnose with the manual and, if it says to replace a speed sensor or the computer, replace the valve body instead. Nissan says not to replace sensors, the computer or the transmission

None of them replaced only the step motor or the whole transmission: the repair was the valve body, which includes the motor, plus the computer. They're US bulletins; we found none that names Mexico, and Mexican models' software may differ. We also found no Mitsubishi, Jeep or Dodge bulletins on the step motor.

Step-by-step diagnosis

This order comes from Nissan's service manuals (2007 Sentra, 2013 Juke and 2010 Cube) and its bulletins. You need a scan tool that reads the CVT computer and a multimeter:

  • Check the fluid before the codes: hot level, leaks and condition. Nissan checks the fluid, line pressure and a stall test before it gets to the step motor. Varnished fluid means heat; milky, water; and a lot of metal powder, internal wear.
  • Read every code in the CVT computer. If there are communication codes (U1000) or speed sensor codes (P0715, P0720), deal with them first: the computer works out the ratio from those sensors.
  • With P1777, check in live data that the motor's step count (STM STEP) and coils A to D change while driving. Then check the harness and connector between the computer and the CVT.
  • Measure the coils with the ignition off and the CVT connector unplugged: about 30 Ω between terminals 6 and 7 and between 8 and 9, and about 15 Ω from each one (6, 7, 8 and 9) to ground. If they're good there but not from the computer connector, the fault is in the harness. The computer's pins change with the model (27 to 30 on the 2007 Sentra and 2013 Juke; 11, 12, 20 and 21 on the 2003 Murano), so use your car's wiring diagram.
  • Don't measure voltage on the motor wires: the computer drives it with pulses, and Nissan states that signal can't be tested with a multimeter, only with its scan tool.
  • With P1778, compare the actual ratio (GEAR RATIO) with the motor's steps (STM STEP) in live data: they should move together. If the motor moves and the ratio doesn't follow, the cause is mechanical: according to Nissan, a clogged control valve or a sticking solenoid valve; according to the rebuilding industry, also pump pressure or a pulley leak. A line pressure test helps tell them apart.

What your results mean

P1777 alone, harness good and coils out of range (open or shorted)The step motor failed. Nissan replaces the whole valve body, which includes it; a replacement motor swaps only the failed part
P1777 with the coils good at the CVT connector but bad from the computerThe harness or connector. Don't replace the motor
P1777 together with P0744, P0840 or P0845In the US, Nissan fixed it by replacing the valve body (2007 and 2008 Sentra, Altima and Rogue)
P1778 alone, no P1777 and good coilsThe ratio isn't following the motor: valve body, the pump's flow control valve, pulley leaks or the speed sensors. Usually not the motor
P1778 with speed sensor codes (P0715, P0720)Fix the sensor circuit first
P1778 with pressure codes or a low pressure testThe pump, pressure regulation or a leak
P1777 or P1778 on a 2013-on Sentra, 2015-on X-Trail, Kicks or PathfinderThose CVTs have no step motor: check the scan tool or the code reading

Can you replace just the step motor?

It's sold separately, but Nissan never replaces it alone: in its manual, the step motor is included in the control valve assembly, so Nissan's repair is the valve body or the transmission. Replacing just the motor makes sense when the tests point to it: P1777 with a coil out of range and a good harness. With P1778 alone, the cause is most likely elsewhere.

The motor sits on the valve body, which you reach by dropping the pan; according to Nissan, replacing the valve body doesn't require removing the transmission. When installing it, mind the linkage between the motor and the ratio control valve: Nissan says to confirm the end of the linkage engages the motor. Then clear the codes and do the test drive the manual calls for to confirm they don't come back.

After the repair

If the valve body is replaced, the computer has to relearn. In its 2010 bulletins, Nissan initializes the computer (erases its calibration memory); on models such as the Juke, it also loads the calibration data that comes with the valve body and clears the fluid degradation counter. Mitsubishi calls for initializing the learned values, resetting the fluid counter and running the CVT learning. There's no published procedure for replacing only the step motor.

Can I drive with P1778?

Only as much as necessary, and only to the shop. In fail-safe the CVT freezes the ratio: it may pull away very slowly or not get past a certain speed. Nissan warns in its owner's manuals that in fail-safe, speed may stay below that of traffic and increase the risk of a collision.

P1777 and P1778 myths

  • "P1778 is the step motor: replace it." Nissan says P1778 sets with the electrical side fine and the mechanical side not, and its bulletins fixed it with the valve body, never with the motor alone.
  • "P1778 means the CVT is finished." In its US bulletins, Nissan fixed it without replacing the transmission, and one explicitly says not to replace it.
  • "Measure the step motor's voltage with a multimeter." The signal is pulses that, according to Nissan, can't be tested with a multimeter. What you can measure is coil resistance, with the connector unplugged.
  • "It's pins 27 to 30 on every Nissan." They change with the model: 27 to 30 on the 2007 Sentra and 2013 Juke, and 11, 12, 20 and 21 on the 2003 Murano.
  • "My 2015 Sentra or my Pathfinder sets P1778." Those CVTs have no step motor and the code doesn't exist in their manuals; their ratio fault shows up as P0965 to P0967.
  • "P1778 means the same on every make." P17xx codes belong to each maker: on a 2019 RAM 1500, P1778 is an input speed sensor code, and Kia lists it among the solenoid codes of its 6-speed automatic.

See JF011E and JF010E CVT parts

TSS step motor parts

When the diagnosis confirms the step motor, or what surrounds it, these are the TSS parts:

JF011E (RE0F10A) step motor: 2007 to 2012 Sentra, 2008 to 2014 X-Trail and 2007 to 2012 Altima 2.5Step motor 125947B
JF010E (RE0F09A) step motor, like the first-generation Murano's, and JF009E (RE0F08A)Step motor 125947A
P1778 with a good motor and low pressure on the JF011EPump flow control valve
Output speed sensor for the Nissan JF011E and JF010EOutput speed sensor
If the CVT needs a rebuildJF011E Rojo overhaul kit or JF010E, JF011E cartridge filter and JF011E internal filter

For the 2012 to 2014 Juke, the Jeep, Dodge and Mitsubishi JF011E, and the JF010E in the 2009 to 2014 Murano and the Altima 3.5, confirm with your distributor which motor fits. And check your transmission in the Transmisiones Veinte 07 transmission finder before ordering. If your CVT shows other codes, look them up in our diagnosis by code.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • What is a CVT step motor?

    A four-coil electric motor on the valve body of JF009E, JF010E and JF011E CVTs. The computer moves it step by step, and it in turn moves the ratio control valve, which sends pressure to or releases it from the primary pulley and changes the ratio.

  • What does code P1777 mean?

    A fault in the step motor circuit: when it switches a coil on and off, the computer doesn't see the voltage change it expects. According to Nissan, the cause is an open or shorted harness or connector, or the motor itself. It's tested by measuring coil resistance with the connector unplugged.

  • What does code P1778 mean?

    That the CVT's actual ratio isn't following the motor's steps. Nissan sets it when the electrical side is fine and the mechanical side isn't, and the 2010 Cube manual states it's caused by a mechanical fault, such as a clogged control valve or a sticking solenoid valve, not a short.

  • Can I drive with P1778?

    Only as much as necessary, and only to the shop. The computer freezes the ratio, so the car may pull away very slowly or not get past a certain speed, and Nissan warns that in fail-safe speed may stay below that of traffic.

  • Can you replace just the step motor?

    It's sold separately, but Nissan never replaces it alone: its manuals replace the valve body or the transmission, and its bulletins the valve body with reprogramming. Replacing just the motor makes sense with P1777, a coil out of range and a good harness; with P1778 alone, the cause is most likely in the valve body, the pump or the pulleys.

  • What should the step motor measure?

    At the CVT connector, with the ignition off and the connector unplugged: about 30 Ω between terminals 6 and 7 and between 8 and 9, and about 15 Ω from each one to ground. It's the same value in Nissan's JF009E, JF010E and JF011E manuals; on the computer side, the pins change with the model.

  • Can my 2015 Sentra, 2017 X-Trail or Versa set P1778?

    No. The 2013-on Sentra and 2015-on X-Trail have CVTs without a step motor, which control the ratio with a pressure solenoid and set P0965 to P0967. And Mexico's 2012 to 2019 Versa and Tiida are 4-speed automatics.

  • Does anything need programming after the repair?

    If the valve body is replaced, yes: Nissan initializes the computer, and on models such as the Juke it also loads the valve body's calibration data and clears the fluid degradation counter. There's no published procedure for replacing only the step motor.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.