
- U0100 is stored by the module that stopped hearing the engine computer (the transmission, ABS, cluster or body module), not by the engine computer.
- U0073 means the module itself couldn't use the network: it stops transmitting and uses default values.
- If several modules store U0100 and the scan tool can't reach the engine computer, check its power feed, grounds, fuses, relay and its branch of the network; the computer comes last.
- Between pins 6 and 14 of the OBD connector, with the ignition off, the network should read about 60 Ω: GM accepts 50 to 70, Ford 54 to 66 and Toyota 54 to 69.
- With U0100 in the transmission module, GM sends the transmission to default gears; on the Mazda3 only learning and stop-start are blocked.
U0100 and U0073 are network codes: they say a module stopped hearing the engine computer or couldn't use the network, not that the transmission is damaged. But on many cars the transmission holds one gear when they show up, so they're worth checking before opening the transmission. If your code is U0101 (the transmission module went missing), it's in our U0101 guide.
What do U0100 and U0073 mean?
U0100's generic name is "lost communication with ECM/PCM 'A'" and U0073's is "control module communication bus 'A' off". What matters is which module stores them:
| Code | What it means |
|---|---|
| U0100 | A module (the transmission, ABS, instrument cluster, body or steering module) stopped receiving the engine computer's (ECM or PCM) messages over the CAN network. GM points out that the code doesn't mean the module storing it is faulty |
| U0073 | The module storing the code couldn't use the network itself: GM sets it when the module tries to communicate more than 3 times in 5 seconds and fails. That module stops transmitting, uses default values and stops storing other communication codes |
| U0101 | Same as U0100, but the missing module is the transmission control module (TCM) |
| U0001 and U0002 | Some makes name the whole network: GM calls it "high speed CAN bus" and Chrysler "CAN C bus off" |
| U1000 and U1001 | Nissan uses these codes of its own for the same fault on almost all its 2005 to 2022 models, instead of U0100 |
Each make adds a suffix: Ford and Mazda write U0100:00 or U0100:87 (missing message), GM U0100 00, 71 or 72, and Honda U0100-F1. The main number means the same thing.
Which module stores it and what that tells you
Before measuring anything, scan every module and note where the code shows up. It's the first clue, according to GM's manuals:
| Where it shows up | What it points to |
|---|---|
| In several modules, and the scan tool can't talk to the engine computer | The engine computer is off the network: check its power feed, grounds, fuses, relay, wake-up wire and its branch of the network. The computer comes last |
| In several modules, but the engine runs and the computer answers | An intermittent loss: a connector, a ground, the wake-up wire or low voltage. Check whether the code is current or history only |
| In one module only | Diagnose that module: its branch, connector and power feed. There are known false codes too: a GM bulletin for the Express and Savana says to ignore it in the body module unless other modules also have it, and Ford has several that say to ignore it when there are no symptoms |
| Together with U0101, U0121 or U0140 | Several modules "lost" at once: look for a shared cause, such as a break in the network, a ground, the power feed or a terminating resistor |
| U0073 in one module | That module dropped off the network. Since it stops storing other communication codes, the absence of U0100 there proves nothing |
U0100 and U0073 symptoms
- Check engine light on, often with several "U" codes at once.
- The transmission holds one gear or shifts hard: GM sends the transmission to "default gears" when its module loses the engine computer, and Cadillac documented hard shifts with U0073 and U0100.
- It won't shift into P or R and the gear letter blinks (GM 9-speeds with an electronic shifter, 2018).
- The engine doesn't crank or start: if the whole high-speed network fails, GM says the engine won't start, and on Mazdas the immobilizer checks the key over the network.
- Gauges that move on their own, service messages and heavy steering from lost power assist (Trax and GM pickups).
- The engine stalls while driving (2014 to 2017 GM pickups with U0073, U0100 and U0101).
What causes these codes?
We went through about 63 service bulletins that makers published in the US between 2002 and 2024 on U0100 and U0073. This is how the causes split (these are published cases, not real-world frequency):
- Software: about 21 bulletins fix it by reprogramming the engine computer, the transmission module or another module.
- Wires, connectors, grounds and terminating resistors: about 18, six of them with water or corrosion.
- False or informational codes: 9 bulletins say to ignore it or that it doesn't affect how the car works.
- A module failed internally: 4 cases, such as the Ford PowerShift module.
- Battery work, a bad jump-start or a failed computer relay: 4 cases.
These are the documented cases on models also sold in Mexico. They're bulletins published in the US; some cover other markets, but we found none that names Mexico:
| Vehicle | Documented cause |
|---|---|
| Chevrolet Trax 2015 to 2020 | A loose ground (G103, on the left front frame rail in front of the battery) set U0073, U0100, U0101 and U0121, with the check engine light and dash messages |
| Chevrolet Equinox 2010 to 2017 | Broken, damaged or corroded wires at the X411 connector set U0073, U0100 and U0101, with ABS and StabiliTrak messages |
| Silverado, Tahoe, Suburban and Escalade 2007 to 2014 (6L80) | Backed-out terminals at the transmission connector, a connector lock not fully seated, water or corrosion in the network and open terminating resistors: the transmission may not shift and the engine may stall |
| Silverado and Sierra 2019 to 2022 | U0100 at start-up with shifting problems: the engine computer isn't getting its wake-up signal, usually from a fault in the first 30 cm (12 in) of wire from its connector |
| Chevrolet City Express 2015 (Nissan NV200) | A reversed wire in the engine harness: cranks but won't start, with U0100 and U1000 in several modules. Nissan says not to replace the computer |
| Ford Fiesta 2011 to 2016 and Focus 2012 to 2016 (PowerShift) | The transmission module fails internally: it loses drive while you're driving or won't start. Ford replaces it only after ruling out low voltage |
| VW Jetta, Golf, Tiguan and Passat 2018 to 2023 | The engine computer gets damaged if, while disconnecting the battery, the positive terminal touches its case: it cranks, won't start and sets U0100. VW says always disconnect the negative first |
| Jeep Renegade 2021 and 2022 (1.8 engine) | Check engine light and no start, with U0100 and U1701: here it really was the engine computer, and Chrysler replaced and programmed it for a list of VINs |
Step-by-step diagnosis
This order comes from the GM, Ford, Toyota, Nissan and Chrysler service manuals. From step 4 on it's shop work: you need a scan tool that reads every module, a multimeter and the vehicle's wiring diagram.
- Step 1. Battery and charging. Test the battery and alternator and check the terminals, cables and grounds. With low voltage, modules drop off at different voltages (Nissan mentions under 10 V), and Ford says to fix any low voltage before replacing a module.
- Step 2. Read every module, not just the engine's, and write down which one stores each code: several modules or just one changes the whole diagnosis. Nissan says to deal with communication codes first and the rest afterwards.
- Step 3. Current or history? Clear the codes, start the engine and let it run for 10 seconds (that's how GM does it). A "U" code left only in history can come from a battery event, and GM says not to replace a module for that.
- Step 4. Power feed to the module that doesn't answer, which with U0100 is almost always the engine computer: fuses, main relay, grounds (GM asks for under 10 Ω and Toyota under 1 Ω on the computer's ground) and the wake-up wire.
- Step 5. Measure the network at the OBD connector. With the ignition off, and the battery disconnected if the manual says so, pins 6 and 14 should read about 60 Ω. Then check that neither line is shorted to ground or to voltage.
- Step 6. If the network is shorted, unplug the modules one at a time until the reading changes, as Ford, Nissan and Toyota do. The last one you unplugged, or its branch, is the one pulling the network down.
- Step 7. Check connectors, splices, water and corrosion: backed-out or bent terminals, locks not fully seated, water that came in through a poorly sealed windshield or the transmission connector. Nissan warns that a bent terminal can pass a visual check.
- Step 8. Accessories added later: navigation radios, GPS trackers, heated-windshield harnesses and other poorly installed accessories show up in GM, Toyota, Isuzu and Chrysler bulletins.
- Step 9. Software and bulletins for your VIN: many cases were fixed by reprogramming a module. Keep the voltage steady while programming; Chrysler asks for 13.2 to 13.5 V.
- Step 10. The module, last. If everything above checks out, it's replaced and programmed. Then clear the codes in every module and test again.
What your results mean
| What you find | What it means and what to do |
|---|---|
| About 60 Ω between pins 6 and 14 | Both 120 Ω terminating resistors are connected: the network is closed at both ends. If the code persists, look for an intermittent fault, a power feed or a branch |
| About 120 Ω | One end is missing: an open wire, a connector or a module's internal resistor. Ford and Toyota isolate it by measuring the harness side at each end |
| Almost 0 Ω (under 3) | CAN high and CAN low are shorted together: unplug modules one at a time |
| 35 to 50 Ω (GM) | There's one terminating resistor too many; GM says it happens when the wrong module is installed |
| Over 6 V on a line with the ignition on (Ford) | That line is shorted to voltage |
| Several modules store U0100 and the engine computer doesn't answer the scan tool | The engine computer is off or cut off: power feed, grounds, relay, wake-up wire and its branch of the network |
| U0100 in one module only, with no symptoms | It may be a known false code or left over from a battery event: look for bulletins before replacing parts |
Makers' test values
The 60 Ω comes from two 120 Ω resistors, one at each end of the network, connected in parallel. Each make gives its own range:
| Make | Value |
|---|---|
| GM | 50 to 70 Ω between pins 6 and 14; under 35 Ω is a short, 35 to 50 Ω means an extra resistor and over 70 Ω is an open or high-resistance circuit. With the ignition on, each line should read under 4.5 V to ground; at rest, about 2.5 V |
| Ford (2014 Fiesta) | 54 to 66 Ω with the battery disconnected; 108 to 132 Ω means a terminating resistor is missing. Wait 5 minutes before measuring: a capacitor inside a module can skew the reading |
| Toyota (2007 FJ Cruiser) | 54 to 69 Ω with the ignition off; 69 Ω or more is an open circuit and under 54 Ω a short. Each line to the connector's ground (pin 4) should read 200 Ω or more |
| Chrysler (2015 to 2018 Jeep Renegade) | About 60 Ω on each of its three networks. The networks "go to sleep" 10 to 12 seconds after the car is turned off and wake up when a door opens |
| Nissan | About 60 Ω with the battery disconnected, and about 120 Ω at each terminating module. CAN high, 2.5 to 3.5 V; CAN low, 1.5 to 2.5 V |
| Kia (2016 on) | At the OBD connector you only measure a single 60 Ω resistor on the diagnostic network; the other networks are measured at the gateway module's connector |
Can I drive with code U0100?
It depends on what the car does; no maker says it's safe. If the code is only in history and the car works normally, get it scanned soon. If the transmission is stuck in one gear, drive little and gently, only to the shop. And if it loses drive, won't go into P or R, the steering gets heavy or the engine stalls, don't drive it: call a tow truck.
U0100 and U0073 myths
- "U0100 means the computer is dead." No: GM says not to replace a module just because it reports a "U" code, and Nissan says not to replace the computer on the NV200. Sometimes it is the computer, but that's confirmed last.
- "Disconnect the battery for 30 minutes and you're done." The code comes back if the cause is still there, on some models it won't clear, and clearing it loses the clue of which module stored it. If you disconnect the battery, take the negative off first.
- "U0100 is a fault between the ECM and the PCM." "ECM/PCM" is a single module, the engine computer; another module stores the code.
- "With U0100 the transmission always goes into limp mode." GM does send it to default gears, but on the 2014 to 2018 Mazda3 only the learning, neutral idle and engine stop-start are blocked.
- "The network must always read 60 Ω at the OBD connector." There are exceptions: networks on other pins, cars with a gateway module, and networks that go to sleep or take a few minutes to discharge.
- "U0073 only lowers fuel economy." Makers document cars that won't start, transmissions that won't shift, engines that stall and lost steering assist.
After the repair
Clear the codes in every module, not just the engine's: several modules store codes during network tests. Then drive and scan again. If you replaced or reprogrammed a computer, finish the programming and the relearns the make calls for. And if the transmission still acts up once the network is fine, look up its own code in our diagnosis by code.
TSS module for the 6T40 and 6T45
U0100 is almost never fixed with a transmission part. The exception is the transmission module: if U0073 or U0100 show up in the module of a 6T40 or 6T45 (Cruze, Sonic, Trax, Malibu, Equinox) and the diagnosis has already ruled out the network, the power feed and the software, TSS has the rebuilt transmission control module (TCM) 24268164 for 2014 on. It's programmed to the VIN, and its failures are in our 6T40 guide.
Confirm your transmission in the Transmisiones Veinte 07 transmission finder before ordering: the module changes with the transmission's year and generation.




