Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
System: Torque converter clutch (TCC)

Code P0740: Torque converter clutch circuit malfunction

A fault in the torque converter clutch or its solenoid: it won't apply, it stays applied or its circuit fails. If it stays applied, the engine can shudder or stall when stopping.

What's failing

Torque converter clutch (TCC)

Most common cause

The torque converter clutch (TCC) solenoid circuit

Can I drive with this code?

Usually it can be driven carefully to the shop, but without lockup fuel use rises and the fluid runs hotter

Diagnosis for your car

What car do you have?

Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.

Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →

Symptoms

  • The converter doesn't lock upAt steady highway speed the rpm doesn't drop like it used to and fuel use goes up.
  • Check engine light on; on some Fords the transmission warning light flashes along with other converter codes
  • If the cause is internal it may slip and shift erraticallyChrysler documented this on the 62TE with P0740, P0868 and P0944 together.
  • With lockup not applying, the fluid tends to run hotter

Most common causes

  1. 1The torque converter clutch (TCC) solenoid circuitWire, connector or power feed. On most units (GM, Nissan) P0740 is a circuit code.
  2. 2Wrong fluid level or typeOn the 46RE, Chrysler warns that fluid other than the recommended type can cause converter shudder.
  3. 3The TCC solenoid itself; Honda says not to replace it without a diagnosis
  4. 4Mind the makeOn Chrysler's 46RE, P0740 isn't electrical, it means no rpm drop when lockup is commanded (performance).
  5. 5The converterOn 2011–2017 62TE units (US), Chrysler found a cracked converter piston scraping off friction material.
  6. 6On rebuilt units, the installationGM documented remanufactured 4T60-E units with no TCC apply and P0740 or P1870.

From most common and easiest to check to least common.

Step-by-step diagnosis

Follow these steps

Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.

Step 1

Are the fluid level and type what the carmaker specifies?

Chrysler warns on the 46RE that a fluid other than the recommended one can make the converter shudder.

It's guidance: a technician with a scan tool makes the final diagnosis.

See every step and resultShow
  1. Step 1. Are the fluid level and type what the carmaker specifies?Yes: step 2 · No: «Correct the fluid»
  2. Step 2. Are the transmission connector and the converter (TCC) solenoid wires clean and tight, with power reaching it?Yes: step 3 · No: «Connector, wires or power supply»
  3. Step 3. Measured at the transmission connector, is the TCC solenoid's resistance within your transmission manual's value?Yes: step 4 · No: «From the connector inward»
  4. Step 4. On the highway, when the computer commands lock-up, do the engine and turbine speeds match on the scan tool?Yes: «Lock-up works» · No: «The converter clutch doesn't apply»

Results

  • Correct the fluid. Set the correct level and type, clear the code and road-test on the highway.
  • Connector, wires or power supply. In most transmissions (GM, Nissan) P0740 is a circuit code: repair the solenoid's connector, wires or power supply before replacing parts.
  • From the connector inward. If it measures wrong at the transmission connector, the problem is the internal harness or the converter solenoid. Honda asks not to replace the solenoid without a diagnosis.
  • The converter clutch doesn't apply. If the circuit is OK and the speeds don't match, check the converter and the lock-up hydraulics: on the 2011–2017 62TE (US), Chrysler found a cracked converter piston. On rebuilt units, check the installation: GM documented a rebuilt 4T60-E with no lock-up.
  • Lock-up works. If the code comes back, move the harness with the scan tool connected to find a bad contact, and ask about a software update.
Diagnostic tip

At steady highway speed in top gear, compare engine rpm with turbine rpm on the scan tool when the computer commands lockup: if the difference doesn't drop close to zero, the converter clutch isn't applying. On the 46RE, Chrysler applies lockup in 4th above about 45 mph.

Can I drive with this code?

Usually it can be driven carefully to the shop, but without lockup fuel use rises and the fluid runs hotter. If it also slips or shifts erratically, stop using it.

What carmaker bulletins say93 carmaker bulletins and the vehicles they nameShow

93 service bulletins published by the US NHTSA mention this code, mostly from RAM, Honda, Chrysler, Dodge, Toyota (1990–2024 models). The repair they mention most: checking or replacing the solenoid.

Vehicles with service bulletins for this code

  • RAM 3500 2007–2022
  • RAM 2500 2009–2022
  • Chrysler Town And Country 2005–2018
  • Dodge Caravan 2005–2020
  • Dodge Journey 2007–2022
  • Chrysler 200 2010–2018
  • Hyundai Elantra 1996–2006
  • Hyundai Tiburon 1997–2008
Bulletin T-SB-0076-24 · 2024
Toyota Tacoma 2024

MIL with DTCs for torque converter clutch stuck off (P07407F) and stuck pressure control solenoids C, L, D, G or H. The automatic transmission and torque converter must be replaced.

Open the bulletin (PDF), page 5 ↗
Bulletin 9004206 · 2022
Chrysler Town And Country 2011–2016 · RAM Promaster 2015–2022 · Dodge Caravan 2011–2020 · Dodge Journey 2011–2020

Notes for the remanufactured 62TE: one-time fasteners, the right unit per year, dowel pins. If it jerks or slips with P0740 or P2764 and the TCC solenoid is OK, replace the torque converter.

Open the bulletin (PDF), page 1 ↗
Bulletin 9004206 · 2022
Dodge Journey 2011–2020 · Dodge Caravan 2011–2020 · Chrysler Town And Country 2011–2016 · RAM Promaster 2015–2021

Notes for the remanufactured 62TE: one-time fasteners, the right unit per year, dowel pins. If it jerks or slips with P0740 or P2764 and the TCC solenoid is OK, replace the torque converter.

Open the bulletin (PDF), page 1 ↗
Bulletin 9004206 · 2022
Dodge Caravan 2011–2020 · Dodge Journey 2011–2020 · Chrysler Town And Country 2011–2016 · Chrysler 200 2011–2014

Notes for the remanufactured 62TE: one-time fasteners, the right unit per year, dowel pins. If it jerks or slips with P0740 or P2764 and the TCC solenoid is OK, replace the torque converter.

Open the bulletin (PDF), page 1 ↗

These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.

TSS parts for the transmissions in these bulletins

Buy in

Different transmission? Pick it and we'll show its parts:

See parts →

Find the part by its number on the exploded diagram: 62TE · 45RFE · CD4E · E4OD · 4T65E

Related codes

← See all codes

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.