4R100 units built 1/1/2001–5/1/2002 may show a flashing transmission control lamp and torque converter clutch DTCs P0740, P0741, P0743 or P1744.
Code P0743: Torque converter clutch circuit electrical
A fault in the torque converter clutch or its solenoid: it won't apply, it stays applied or its circuit fails. If it stays applied, the engine can shudder or stall when stopping.
Torque converter clutch (TCC)
The solenoid or case connector
It usually still drives, just without lockup
What car do you have?
Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.
Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →
Symptoms
- The converter doesn't lock upHigher rpm at steady highway speed and higher fuel use.
- Check engine light on; on some Fords the transmission warning light flashes
- On some makes, limp modeHyundai documented 6-speeds held in 4th with solenoid codes including P0743, and 4-speeds held in 3rd (US).
- It may set along with other solenoid codes when the fault is in something they share, such as the connector or harness
Most common causes
- 1The solenoid or case connectorLoose, bent, wet or corroded pins. Hyundai asks to check connectors and pins before replacing parts.
- 2The wires between the computer and the transmission, open or shorted
- 3The power feedOn Chrysler's 46RE, P0743 covers the TCC solenoid circuit and the transmission relay circuit.
- 4The internal harnessOver the years heat hardens and cracks the insulation (on Ford's AX4N and 4F50N, P0743 is among the possible codes).
- 5The torque converter clutch (TCC) solenoidOn Hyundai and Kia 6-speeds, Hyundai replaces the solenoid named by the code and its harness.
- 6The computer, last
From most common and easiest to check to least common.
Follow these steps
Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.
Measured at the transmission connector, is the converter (TCC) solenoid's resistance within the manual's value?
It's an electrical code. There's no universal value: use your transmission manual's.
It's guidance: a technician with a scan tool makes the final diagnosis.
See every step and resultShow
- Step 1. Measured at the transmission connector, is the converter (TCC) solenoid's resistance within the manual's value?Yes: step 3 · No: step 2
- Step 2. Are the transmission connector and its pins clean and tight, with no water, corrosion or bent pins?Yes: «Internal harness or solenoid» · No: «Repair the connector»
- Step 3. Are the wires between the computer and the transmission OK, with no opens or shorts, and is power getting through?Yes: step 4 · No: «Wires or power supply»
- Step 4. With the scan tool connected, does the code or the reading change when you move the harness?Yes: «Bad contact» · No: «The computer, last»
Results
- Repair the connector. Clean or repair the connector and pins, clear the code and test again.
- Internal harness or solenoid. With the connector OK and the reading wrong, the problem is inside the transmission: the internal harness, whose insulation hardens and cracks with heat (on Ford's AX4N and 4F50N), or the converter solenoid. On Hyundai and Kia 6-speeds, Hyundai replaces the solenoid that sets the code and its harness.
- Wires or power supply. Repair the open or shorted wire between the computer and the transmission, or the power supply, before touching the solenoid.
- Bad contact. If it changes when you move the harness, that's where the fault is: find the damaged connector or section and repair it.
- The computer, last. With the solenoid, connector, wires and power supply OK, check the computer, always last.
It's an electrical code: measure the solenoid resistance from the transmission case connector and compare it with the spec for that transmission (there's no universal value). If it reads good there, the fault is between that connector and the computer; wiggle the harness with the scan tool connected to find an intermittent contact.
It usually still drives, just without lockup. If it goes into limp mode (for example, held in 4th on a Hyundai or Kia 6-speed), drive it only to the shop.
What carmaker bulletins say18 carmaker bulletins and the vehicles they nameShow
18 service bulletins published by the US NHTSA mention this code, mostly from Hyundai, Ford, Lincoln, Santa Fe, Kia (1996–2017 models).
Vehicles with service bulletins for this code
- Hyundai Elantra 1996–2007
- Hyundai Santa Fe 2001–2010
- Ford Super Duty F Series 2001–2002
- Ford Expedition 2001–2002
- Lincoln Navigator 2001–2003
- Lincoln Blackwood 2002
- Kia Forte 2011–2015
- Kia Sportage 2011–2014
Flashing transmission control indicator lamp (TCIL) and torque converter clutch DTCs P0740, P0741, P0743 and P1744.
Solenoid DTCs P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773 and P2709. Incorrect solenoid operation causes a check engine light and the transaxle held in 4th (fail-safe).
These are US bulletins: check with your dealer or shop whether they apply to your car.
TSS parts for the transmissions in these bulletins
Different transmission? Pick it and we'll show its parts:
Find the part by its number on the exploded diagram: E4OD
Buying wholesale or own a parts store?
We'll send you a quote or tell you how to sell TSS in your area.
