Rotary shifter (ESM) stuck in PARK with DTCs P0928-00 and P0705. ESM parts 68171964AI, 68171965AK, 68517473AA and 68517474AA are replaced with 68517473AB or 68517474AB.
Open the bulletin (PDF), page 1 ↗Code P0705: Transmission range sensor circuit malfunction (PRNDL input)
The computer can't make sense of the sensor that tells it the lever position (P, R, N, D): it sees two positions at once, none, or an out-of-range signal.
Range sensor (TR switch)
A misadjusted shift cable or sensor, especially after the transmission was removed or the linkage disconnected (on Ford's digital sensor, Ford says adjustment doesn't cause it).
No maker says it's safe
What car do you have?
Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.
Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →
Symptoms
- No crank in P or N, or it cranks only sometimes
- The dash doesn't show the selector position, or shows the wrong one
- Limp modeIt stays in one gear (4th on Hyundai and Kia 6-speeds; 3rd or 5th on Ford's 6R80).
- Harsh engagement into D or R, because the computer raises pressure to maximum to protect itself
- Reverse lights don't come on, or come on outside of R
Most common causes
- 1A misadjusted shift cable or sensor, especially after the transmission was removed or the linkage disconnected (on Ford's digital sensor, Ford says adjustment doesn't cause it)
- 2Water, corrosion or a bad ground at the connector or harnessNissan traced P0705 on the 2012–2014 Versa (US) to water entering through the tail lamps and said not to replace the CVT.
- 3A chafed wire shorting to ground or to power, or a blown fuse that leaves the sensor without power
- 4A damaged or worn range sensor
- 5On units with an internal sensor (Ford 6R80, GM IMS, several CVTs), the link to the manual valve or metal debris
- 6The computer or its software, always last; also low battery voltage or a badly installed alarm or remote starter
From most common and easiest to check to least common.
Follow these steps
Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.
Are there voltage or communication codes (U0100, U0101, P0882), or does the battery read under 12 V?
It's guidance: a technician with a scan tool makes the final diagnosis.
See every step and resultShow
- Step 1. Are there voltage or communication codes (U0100, U0101, P0882), or does the battery read under 12 V?Yes: «Fix the voltage and communication first» · No: step 2
- Step 2. With the engine off and the brake pressed, does the position on the scan tool match the shifter in P, R, N and D?Yes: step 3 · No: step 4
- Step 3. With the scan tool connected, does the reading jump when you move the sensor's harness and connector?Yes: «Connector or harness» · No: «Intermittent fault»
- Step 4. Does the scan tool show a different position than the shifter (for example, N with the shifter in D)?Yes: «Cable or sensor out of adjustment» · No: step 5
- Step 5. Does it show two positions at once (for example, P and R)?Yes: step 6 · No: step 7
- Step 6. Unplugged, does the sensor pass the multimeter test position by position?Yes: «Shorted or wet wires» · No: «Damaged range sensor»
- Step 7. With the key ON, is the fuse good and is there power at the sensor connector?Yes: step 6 · No: «Fuse or power supply»
Results
- Fix the voltage and communication first. Charge the battery if it reads under 12 V and repair the voltage or communication codes first: they have their own page in this tool. Then clear the codes and test again.
- Connector or harness. If the reading jumps when you move the harness, the problem is the connector or the wires, not the sensor: repair it before replacing parts. Nissan traced P0705 on the 2012–2014 Versa (US) to water coming in through the tail lights and asked not to replace the CVT.
- Intermittent fault. If the scan tool matches in every position and the reading doesn't jump, check grounds and water in the connectors and test under the carmaker's conditions. If everything passes and the code comes back, ask about a software update; the computer comes last.
- Cable or sensor out of adjustment. Adjust it with the shifter in N, using the carmaker's gauge or pin (except Ford's digital sensor), and check again: it's the number one cause after work on the transmission. If it still fails once adjusted, test the sensor.
- Shorted or wet wires. If the sensor passes the test, look for wires touching each other, a chafed wire shorted to ground or to power, or water in the harness, and repair it.
- Damaged range sensor. Replace it and adjust it as the carmaker specifies. Then clear the codes and check that the engine only cranks in P and N, the reverse lights come on only in R, and the dash reads correctly.
- Fuse or power supply. Repair the fuse or the open in the power supply before touching the sensor. If the fuse blows again, look for a chafed, shorted wire.
Engine off, foot on the brake, display the range sensor data on the scan tool and move through P, R, N and D: it must match the selector in every position and never show two at once. On Toyota (A750F, U140F), the unplugged sensor reads under 1 Ω in its position and 10 kΩ or more in the others.
No maker says it's safe. If it drives normally, take it carefully to the shop; if the selector doesn't match the dash or it won't crank in P or N, don't drive it: it may not restart or, on some models, may drop into neutral.
What carmaker bulletins say46 carmaker bulletins and the vehicles they nameShow
46 service bulletins published by the US NHTSA mention this code, mostly from Hyundai, Ford, Cadillac, Honda, Kia (1998–2024 models).
Vehicles with service bulletins for this code
- Hyundai Sonata 1999–2023
- Hyundai Santa Fe 2001–2023
- Ford Focus 2000–2005
- Cadillac CTS 2014–2015
- Honda Passport 1998–1999
- Chevrolet Spark 2013
- Kia Sportage 2010–2017
- Kia Sedona 2010–2017
Service action SA317A to replace the inhibitor switch on FWD 6-speed units: P0705, CAN codes, intermittent no start, harsh shifts and 'P' not shown in the cluster.
Open the bulletin (PDF), page 1 ↗Procedure to replace the inhibitor switch. A possible symptom is DTC P0705 (transmission range sensor circuit).
Open the bulletin (PDF), page 2 ↗Procedure to replace the inhibitor switch. A possible symptom is DTC P0705 (transmission range sensor circuit).
Open the bulletin (PDF), page 2 ↗These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.
TSS parts for this code
Pick your transmission to see the TSS parts that fit it, or open all parts of this type:
Buying wholesale or own a parts store?
We'll send you a quote or tell you how to sell TSS in your area.