Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
System: Range sensor (TR switch)

Code P0707: Transmission range sensor circuit low

The computer can't make sense of the sensor that tells it the lever position (P, R, N, D): it sees two positions at once, none, or an out-of-range signal.

What's failing

Range sensor (TR switch)

Most common cause

A misadjusted shift cable or sensor

Can I drive with this code?

If the shifter doesn't match the dash or it won't crank in P or N, don't drive it

Diagnosis for your car

What car do you have?

Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.

Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →

Symptoms

  • No crank in P or N, or it cranks only sometimes
  • The dash doesn't show the shifter position, or shows the wrong one
  • Limp modeOn the 2023 Compass (US), Jeep documented the transmission in limp mode.
  • Check engine light on; the reverse lights may not come on in R, because the same sensor controls them

Most common causes

  1. 1A misadjusted shift cable or sensorOn Chevrolet W-Series and Isuzu N-Series trucks (US), many switches replaced for P0707 had no fault, and the maker asks to check a fuse and the cable adjustment first.
  2. 2A chafed or pinched wireOn the 2023 Compass (US), the transmission harness rubbed a sharp edge of the engine computer; on the 2009 Tribute (US), Mazda found a wire pinched between the valve body and the case.
  3. 3Water, corrosion or damaged pins at the sensor connector, or a blown fuse
  4. 4The range sensor; on units with an internal sensor, the part that carries itOn the 2015–2017 F-150 with the 6R80 (US), Ford replaced the lead frame under a service program.
  5. 5The computer, last

From most common and easiest to check to least common.

Step-by-step diagnosis

Follow these steps

Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.

Step 1

Are there voltage or communication codes (U0100, U0101, P0882), or does the battery read under 12 V?

It's guidance: a technician with a scan tool makes the final diagnosis.

See every step and resultShow
  1. Step 1. Are there voltage or communication codes (U0100, U0101, P0882), or does the battery read under 12 V?Yes: «Fix the voltage and communication first» · No: step 2
  2. Step 2. With the key ON, is the fuse good and is there power at the sensor connector?Yes: step 3 · No: «Fuse or power supply»
  3. Step 3. With the shifter in N, are the shift cable and the sensor correctly adjusted, with no stretched cable?Yes: step 4 · No: «Cable or sensor out of adjustment»
  4. Step 4. With the engine off and the brake pressed, does the position on the scan tool jump when you wiggle the harness while going through P, R, N and D?Yes: «Chafed or pinched wire» · No: step 5
  5. Step 5. Is the sensor connector clean and tight, with no water, corrosion or damaged pins?Yes: step 6 · No: «Repair the connector»
  6. Step 6. Unplugged, does the sensor pass the multimeter test position by position?Yes: step 7 · No: «Damaged range sensor»
  7. Step 7. Are the wires between the sensor and the computer OK, with no opens or shorts to ground?Yes: «The computer, last» · No: «Chafed or pinched wire»

Results

  • Fix the voltage and communication first. Charge the battery if it reads under 12 V and repair the voltage or communication codes first: they have their own page in this tool. Then clear the codes and test again.
  • Fuse or power supply. Repair the fuse or the open in the power supply before touching the sensor. If the reference is low, look for another shorted circuit pulling it down: on the 2003–2007 Super Duty 6.0 diesel, Ford found a shorted fan clutch circuit and asked not to replace the range sensor for this.
  • Cable or sensor out of adjustment. Adjust it with the shifter in N, using the carmaker's gauge or pin, and check again on the scan tool. If it still fails once adjusted, move on to the harness and connector before replacing the sensor.
  • Chafed or pinched wire. Find the chafed or pinched wire and repair it before replacing the sensor: on the 2023 Compass (US), the transmission harness rubbed a sharp edge of the engine computer, and on the 2009 Tribute (US), Mazda found a wire pinched between the valve body and the case.
  • Repair the connector. Clean or repair the connector and damaged pins, clear the codes and check the position on the scan tool again.
  • Damaged range sensor. Replace it and adjust it as the carmaker specifies. On units with an internal sensor, the part that carries it is replaced: on the 2015–2017 F-150 with the 6R80 (US), Ford replaced the lead frame under a service program. Then check that it only cranks in P and N and the reverse lights come on only in R.
  • The computer, last. With the power supply, adjustment, connector, sensor and wires OK, ask about a software update; the computer comes last.
Diagnostic tip

Watch the definition: on Hyundai and Kia, P0707 is an open circuit; on Ford, a low signal. With the brake pressed and the engine off, move the shifter through P, R, N and D while watching the position the computer sees on the scan tool, and wiggle the harness as you go: if the reading jumps, look for the chafed wire before replacing the sensor.

Can I drive with this code?

If the shifter doesn't match the dash or it won't crank in P or N, don't drive it; if it moves normally, take it carefully to the shop, because it may not restart.

What carmaker bulletins say12 carmaker bulletins and the vehicles they nameShow

12 service bulletins published by the US NHTSA mention this code, mostly from Hyundai, Chevrolet, GMC, Unknown, Mazda (1999–2023 models). The repair they mention most: checking or replacing the sensor or switch.

Vehicles with service bulletins for this code

  • Hyundai Azera 2005–2017
  • Hyundai Elantra 1999–2020
  • Chevrolet W-Series 2007–2010
  • GMC W-Series 2007–2010
  • Mazda Tribute 2009
  • Jeep Compass 2023
  • GMC Sierra 1500 2019–2021
  • Chevrolet Silverado 1500 2019–2021
Bulletin IB15-K-002A · 2016
Chevrolet W-Series 2007–2010 · Isuzu N-Series 2007–2017 · GMC W-Series 2007–2010

Many inhibitor switches replaced for P0707 had no fault. First check fuse F-18, then check and adjust the shift cable before diagnosing P0707; the adjustment procedure is included.

Open the bulletin (PDF), page 1 ↗
Bulletin SB-05-006-09 · 2009
Mazda Tribute 2009

No crank and/or DTCs P0706, P0707 or P1702. May be caused by the OSS sensor wire pinched between the main control and case, or an intermittently shorted TR sensor.

Bulletin 0814123 · 2023
Jeep Compass 2023

Transmission harness rubbing a sharp PCM edge: MIL with P0882, P0883, P0983 or P0707 and limp mode. Fix is installing foil tape and possibly repairing the harness.

Open the bulletin (PDF), page 3 ↗
Bulletin TSB-09-AT-013 · 2009
Hyundai Xg350 2001–2005 · Hyundai Hyundai 1999–2002 · Hyundai Sonata Gls 1999 · Hyundai Excel 2001

Range switch DTCs P0705, P0707 and P0708 from an improperly adjusted or operating switch. Symptoms: MIL on and no engine start in P or N.

These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.

TSS parts for this code

Pick your transmission to see the TSS parts that fit it, or open all parts of this type:

See parts →

Related codes

← See all codes

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.