Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
System: Range sensor (TR switch)

Code P0708: Transmission range sensor circuit high

The computer can't make sense of the sensor that tells it the lever position (P, R, N, D): it sees two positions at once, none, or an out-of-range signal.

What's failing

Range sensor (TR switch)

Most common cause

A misadjusted or failing switch

Can I drive with this code?

If the shifter doesn't match the dash or it won't crank in P or N, don't drive it

Diagnosis for your car

What car do you have?

Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.

Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →

Symptoms

  • No crankOn Allison 1000 and 2000 units, an active P0708 leaves the truck unable to start (US).
  • The dash shows the wrong position or the computer sees two positions at once; check engine light on
  • Shift system fault warningOn the 2021 Bronco Sport (US), Ford documented it together with P0709.
  • Limp mode or harsh engagements, because the computer raises pressure to protect itself

Most common causes

  1. 1A misadjusted or failing switchHyundai documented P0705, P0707 and P0708 from an improperly adjusted switch, with the MIL on and no crank in P or N (US).
  2. 2A short between circuits or to voltageOn Hyundai and Kia, P0708 means a short or several positions active at once.
  3. 3Water or corrosion in the connector, or a chafed wire
  4. 4SoftwareOn the 2021 Bronco Sport (US), Ford fixed it by reprogramming the computer.
  5. 5The sensor; on units with an internal sensor (6R80, several CVTs), the part that carries it
  6. 6The computer, last

From most common and easiest to check to least common.

Step-by-step diagnosis

Follow these steps

Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.

Step 1

Are there voltage or communication codes (U0100, U0101, P0882), or does the battery read under 12 V?

GM asks to check the battery first, because low voltage can set P0708.

It's guidance: a technician with a scan tool makes the final diagnosis.

See every step and resultShow
  1. Step 1. Are there voltage or communication codes (U0100, U0101, P0882), or does the battery read under 12 V?Yes: «Fix the voltage and communication first» · No: step 2
  2. Step 2. With the engine off and the brake pressed, going through P, R, N and D, does the scan tool show two positions at once in any of them?Yes: step 3 · No: step 5
  3. Step 3. Unplugged, does the sensor pass the multimeter test position by position?Yes: step 4 · No: «Damaged range sensor»
  4. Step 4. Are the connector and harness dry, with no wires touching each other or chafed?Yes: step 7 · No: «Water or shorted wires»
  5. Step 5. Does the position on the scan tool match the shifter in every position?Yes: step 6 · No: «Cable or sensor out of adjustment»
  6. Step 6. Is the connector clean, with no water or corrosion, and does the reading stay steady when you move the harness?Yes: step 7 · No: «Water or shorted wires»
  7. Step 7. Is there a software update for your VIN?Yes: «Update the software» · No: «The computer, last»

Results

  • Fix the voltage and communication first. Charge the battery if it reads under 12 V and repair the voltage or communication codes first: they have their own page in this tool. Then clear the codes and test again.
  • Damaged range sensor. Replace it and adjust it as the carmaker specifies; on units with an internal sensor (6R80, several CVTs), the part that carries it is replaced. Then clear the codes and check that it only cranks in P and N, the reverse lights come on only in R and the dash reads correctly.
  • Water or shorted wires. Dry and repair the connector, and repair any wires that touch each other or are chafed, before replacing the sensor. Then clear the codes and check the position on the scan tool again.
  • Cable or sensor out of adjustment. Adjust it with the shifter in N, using the carmaker's gauge or pin, and check again: Hyundai documented P0705, P0707 and P0708 from an improperly adjusted switch (US). If it still fails once adjusted, test the sensor.
  • Update the software. Ask the dealer for the reflash for your VIN, as Ford did on the 2021 Bronco Sport (US), and read the codes again afterwards.
  • The computer, last. With the battery, sensor, connector, wires and software ruled out, check the computer, always last.
Diagnostic tip

On Hyundai and Kia, P0708 is a short or several positions at once; on Ford, a high signal. Run the shifter through every position on the scan tool: if two positions light up at once, test the sensor unplugged, position by position, against its manual's table, and look for water or wires touching.

Can I drive with this code?

If the shifter doesn't match the dash or it won't crank in P or N, don't drive it; if it moves normally, take it carefully to the shop, because it may not restart.

What carmaker bulletins say17 carmaker bulletins and the vehicles they nameShow

17 service bulletins published by the US NHTSA mention this code, mostly from Hyundai, GMC, Chevrolet, Ford, Unknown (1999–2021 models).

Vehicles with service bulletins for this code

  • Hyundai Sonata 1999–2019
  • Hyundai Azera 2005–2017
  • GMC Sierra 2001–2004
  • Chevrolet Silverado 2001–2004
  • Ford Transit 2020–2021
  • Cadillac Escalade 2020
  • Chevrolet Suburban 2020
  • GMC Sierra 1500 2020
Bulletin TSB 21-2331 · 2021
Ford Bronco Sport 2021

Shift system fault warning and MIL with P0708, P0709, P2803, 2804 and/or P07E6 due to software calibration. The fix is reprogramming the PCM.

Open the bulletin (PDF) ↗
Bulletin PIP5722A · 2020
Cadillac Escalade 2020 · Chevrolet Suburban 2020 · Chevrolet Tahoe 2020 · GMC Sierra 1500 2020

GM preliminary information with diagnostic tips to find the root cause of P0708 on 8L45, 8L90, 10L60, 10L80 and 10L90 transmissions.

Open the bulletin (PDF), page 1 ↗
Bulletin SIL 13 1K2K 16 · 2016
Allison 1000 Series Transmission · Allison 2000 Series Transmission

Truck does not start with an active DTC P0708 (transmission range sensor circuit high input).

Open the bulletin (PDF), page 1 ↗
Bulletin 0640015 · 2006
Hyundai Sonata 2006–2007

Bulletin about automatic transaxle DTC P0708.

These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.

TSS parts for this code

Pick your transmission to see the TSS parts that fit it, or open all parts of this type:

See parts →

Related codes

← See all codes

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.