Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
System: Range sensor (TR switch)

Code P0706: Transmission range sensor range/performance

The computer can't make sense of the sensor that tells it the lever position (P, R, N, D): it sees two positions at once, none, or an out-of-range signal.

What's failing

Range sensor (TR switch)

Most common cause

A misadjusted shift cable or sensor

Can I drive with this code?

Carefully and only to the shop

Diagnosis for your car

What car do you have?

Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.

Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →

Symptoms

  • Check engine light or a transmission fault message on the dash
  • The position shown on the dash doesn't match the selector, or it won't crank in P or N
  • Limp modeIt stays in one gear, for example in 3rd on Renault and Peugeot automatics (DP0 and AL4).
  • On the 2015–2017 F-150 (US), Ford documented the transmission could abruptly downshift to 2nd when it lost the range sensor signal

Most common causes

  1. 1A misadjusted shift cable or sensorNissan sets P0706 when it sees no position for 30 seconds, from an open circuit or a misadjusted cable.
  2. 2A corroded or damaged range sensor connectorAudi found this at the F125 switch terminals on the Q7 (0C8 transmission).
  3. 3The range sensor or switch itself (the multifunction switch on Renault and Peugeot DP0/AL4 units and on the Optra's ZF 4HP16)
  4. 4On units with an internal sensor, the part that carries itOn the 6R80, the lead frame, which Ford replaces under a service program on 2015–2017 F-150s in the US.
  5. 5Another shorted sensor pulling down a shared supplyThe rebuilding industry documented a 6R80 F-150 with no crank and range sensor codes caused by a camshaft sensor.
  6. 6The computerOn some Audis with the 0AW multitronic (US), Audi found a reaction between the transmission computer and the fluid, and replaced both.

From most common and easiest to check to least common.

Step-by-step diagnosis

Follow these steps

Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.

Step 1

Are there voltage or communication codes (U0100, U0101, P0882), or does the battery read under 12 V?

It's guidance: a technician with a scan tool makes the final diagnosis.

See every step and resultShow
  1. Step 1. Are there voltage or communication codes (U0100, U0101, P0882), or does the battery read under 12 V?Yes: «Fix the voltage and communication first» · No: step 2
  2. Step 2. With the engine off and the brake pressed, does the position on the scan tool match the shifter in P, R, N and D?Yes: step 3 · No: step 4
  3. Step 3. With the scan tool connected, does the reading jump when you move the sensor's harness and connector?Yes: «Connector or harness» · No: «Intermittent fault»
  4. Step 4. With the shifter in N, are the shift cable and the sensor correctly adjusted?Yes: step 5 · No: «Cable or sensor out of adjustment»
  5. Step 5. Is the sensor connector clean and tight, with no water, corrosion or bent pins?Yes: step 6 · No: «Connector or harness»
  6. Step 6. With the key ON, are the fuses good and is there power at the sensor connector?Yes: step 7 · No: «Fuse or power supply»
  7. Step 7. Unplugged, does the sensor pass the multimeter test position by position?Yes: step 8 · No: «Damaged range sensor»
  8. Step 8. Are the wires between the sensor and the computer OK, with no shorts to ground or to power?Yes: «Software, and the computer last» · No: «Connector or harness»

Results

  • Fix the voltage and communication first. Charge the battery if it reads under 12 V and repair the voltage or communication codes first: they have their own page in this tool. Then clear the codes and test again.
  • Connector or harness. The problem is the connector or the wires, not the sensor: clean or repair the pins and the damaged section before replacing parts. Then clear the codes and test again.
  • Intermittent fault. If the scan tool matches in every position and the reading doesn't jump, check grounds and water in the connectors and test under the carmaker's conditions. If everything passes and the code comes back, ask about a software update; the computer comes last.
  • Cable or sensor out of adjustment. Adjust it with the shifter in N, using the carmaker's gauge or pin, and check again on the scan tool. If it still fails once adjusted, check the connector and, last, the sensor.
  • Fuse or power supply. Repair the fuse or the open in the power supply before touching the sensor. If the reference is low, look for another shorted circuit pulling it down: on the Super Duty 6.0 diesel, Ford asks to unplug the fan clutch before touching the transmission and not to replace the range sensor for this.
  • Damaged range sensor. Replace it and adjust it in N as the carmaker specifies. On units with an internal sensor, the part that carries it is replaced: on the 6R80, the lead frame, which Ford replaces under a service program on 2015–2017 F-150s (US). Then check that it only cranks in P and N and the dash reads correctly.
  • Software, and the computer last. With the adjustment, connector, power supply, sensor and wires OK, ask about a software update; the computer comes last. On some Audis with the 0AW multitronic (US), Audi found a reaction between the transmission computer and the fluid, and replaced both.
Diagnostic tip

Foot on the brake, engine off, move the selector through P, R, N and D and compare the position the computer sees on the scan tool. If one position shows nothing, check the cable and sensor adjustment in N first, then the connector, and the sensor last.

Can I drive with this code?

Carefully and only to the shop: depending on the vehicle it stays in one gear or may not restart. If the selector doesn't match the dash, don't drive it.

What carmaker bulletins say31 carmaker bulletins and the vehicles they nameShow

31 service bulletins published by the US NHTSA mention this code, mostly from Audi, Hyundai, Chevrolet, GMC, Mazda (1995–2024 models).

Vehicles with service bulletins for this code

  • Audi A6 2002–2014
  • Audi A5 Cabriolet 2012–2014
  • Hyundai Santa Fe 2007–2023
  • Hyundai Sonata 2011–2023
  • GMC Sierra 2001–2005
  • Chevrolet Silverado 2001–2005
  • Chevrolet Avalanche 2003
  • GMC Yukon 2003
Bulletin 37131020348631 · 2022
Audi A6 2012–2013 · Audi A5 Cabriolet 2012–2013 · Audi A4 2013

Gearbox malfunction message in the instrument cluster with DTC P0706.

Open the bulletin (PDF), page 1 ↗
Bulletin A371664 20348634 · 2016
Audi A5 Cabriolet 2012–2013 · Audi A6 2012–2014 · Audi A4 Allroad 2013–2014 · Audi A4 Avant 2012

Explains how to flush the ATF before replacing the TCM to resolve the issue that causes DTC P0706.

Open the bulletin (PDF), page 1 ↗
Bulletin A971550 2034863- · 2015
Audi A6 2012–2014 · Audi A5 Cabriolet 2012–2014 · Audi A4 Allroad 2013–2014

Gearbox warning message with DTC P0706 (driving mode sensor, implausible signal) in the TCM, caused by a reaction between the TCM and the ATF in a specific VIN range.

Open the bulletin (PDF), page 1 ↗
Bulletin A371318 2034863- · 2013
Audi A4 Allroad 2013 · Audi A6 2012–2013 · Audi A5 Cabriolet 2012–2013

Gearbox warning message with DTC P0706 (driving mode sensor, implausible signal) in the TCM, caused by a reaction between the TCM and the ATF in a specific VIN range.

Open the bulletin (PDF), page 1 ↗

These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.

TSS parts for the transmissions in these bulletins

Buy in

Different transmission? Pick it and we'll show its parts:

See parts →

Find the part by its number on the exploded diagram: 4L80E

Related codes

← See all codes

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.