'Service AT Power reduced' warning with P0715 (input speed sensor A) as the only TCM code. Confirm the TCM part number and reprogram it if applicable.
Open the bulletin (PDF), page 2 ↗Code P0715: Input/turbine speed sensor circuit malfunction
The computer gets no signal, or an illogical one, from a transmission speed sensor. Without it, it doesn't know when to shift and usually goes into limp mode.
Speed sensors (input, turbine or output)
The input (turbine) speed sensor connector or wiring
To the shop, carefully
What car do you have?
Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.
Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →
Symptoms
- Harsh, late or mistimed shifts, because the computer doesn't know how fast the input is turning
- Limp modeOn Ford's 6R80 it defaults to 5th with maximum line pressure, so it pulls away weakly and engages with a bang.
- The torque converter stops locking upHigher rpm on the highway and higher fuel use.
- The speedometer still works; if it drops to 0, the output sensor (P0720) is more likely
Most common causes
- 1The input (turbine) speed sensor connector or wiringLoose, damaged or corroded; the most common and cheapest thing to check.
- 2Metal debris stuck to the sensor's magnetic tip, from normal transmission wear
- 3On units with an internal sensor, the part that carries itOn the 6R80, the lead frame with its connector and harness.
- 4Another sensor sharing the same reference supply and pulling it to groundThe rebuilding industry has documented this on Fords (5R110W, 6R80), where range sensor codes also set.
- 5A failed sensorOn the VW 01M it's G38 (code 00297) and on the 09G, G182.
- 6The computer or its software, last
From most common and easiest to check to least common.
Follow these steps
Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.
While driving, does the scan tool show input (turbine) speed while the output speed rises?
On Ford 6R transmissions, the code sets when the output sensor reads speed and the turbine sensor reads 0 rpm.
It's guidance: a technician with a scan tool makes the final diagnosis.
See every step and resultShow
- Step 1. While driving, does the scan tool show input (turbine) speed while the output speed rises?Yes: step 2 · No: step 3
- Step 2. Does the turbine reading drop out when you move the harness or connector?Yes: «Connector or wire» · No: «Intermittent or software fault»
- Step 3. Are the input sensor's connector and wires OK, with no corrosion, looseness or damage?Yes: step 4 · No: «Connector or wire»
- Step 4. Are codes from other sensors, such as the range sensor, set at the same time?Yes: «Check the other sensor» · No: step 5
- Step 5. Is the sensor's magnetic tip clean, with no metal debris?Yes: «Replace the input speed sensor» · No: «Debris on the tip»
Results
- Connector or wire. If the reading drops out when you move the harness, or the connector is damaged, the problem is the connector or the wire, not the sensor: it's the most common and cheapest thing to check. Repair it and test again.
- Intermittent or software fault. If the signal doesn't drop out, check grounds and connections and ask about a software update; the computer comes last.
- Check the other sensor. Another sensor sharing the reference supply can pull it to ground: rebuilders documented it on Ford (5R110W, 6R80), where range sensor codes also set. Check that sensor and its circuit before replacing the turbine sensor.
- Debris on the tip. Clean off the metal debris: it comes from wear inside the transmission, so check the fluid and filter too.
- Replace the input speed sensor. With the connector, wires and tip OK, the sensor is the suspect. In transmissions with an internal sensor it comes in another part: on the 6R80, the lead frame. On VW's 01M it's the G38, and on the 09G the G182.
Compare input (turbine) speed with output speed on the scan tool while driving: on Ford 6R units the code sets when the output sensor shows speed and the turbine sensor shows 0 rpm. If the turbine reading drops out when you wiggle the harness, it's the connector or a wire, not the sensor.
To the shop, carefully: the transmission usually locks in one gear with high pressure, so it pulls away slowly and engagements hit hard.
What carmaker bulletins say25 carmaker bulletins and the vehicles they nameShow
25 service bulletins published by the US NHTSA mention this code, mostly from Ford, Lincoln, Land Rover, Hyundai, Mercury (1998–2022 models).
Vehicles with service bulletins for this code
- Ford Taurus 2008–2016
- Lincoln MKX 2007–2016
- Ford Windstar 1999
- Lincoln MKZ 2007–2016
- Toyota Highlander 2017–2018
- Toyota Sienna 2017–2018
- Hyundai Tucson 2005
- Hyundai Tiburon 2003
'Service AT Power reduced' warning with P0715 (input speed sensor A) as the only TCM code. Confirm the TCM part number and reprogram it if applicable.
Open the bulletin (PDF), page 2 ↗The 'D' may flash on the shifter or cluster after an Auto Stop/Start event, with DTCs P0715-64 and P0700-02 in the TCM and a 'Gearbox Fault' message.
Open the bulletin (PDF), page 3 ↗These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.
TSS parts for the transmissions in these bulletins
Different transmission? Pick it and we'll show its parts:
Find the part by its number on the exploded diagram: 6T70
Buying wholesale or own a parts store?
We'll send you a quote or tell you how to sell TSS in your area.

