Intermittent harsh or jerky upshifts under steady acceleration, or MIL on with DTC P0716.
Open the bulletin (PDF), page 3 ↗Code P0716: Input/turbine speed sensor range/performance
The computer gets no signal, or an illogical one, from a transmission speed sensor. Without it, it doesn't know when to shift and usually goes into limp mode.
Speed sensors (input, turbine or output)
The input (turbine) speed sensor connector or wiring
Carefully and only to the shop
What car do you have?
Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.
Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →
Symptoms
- Harsh or jerky shiftsHonda documented it on the 2018–2019 Odyssey with the 9-speed (US).
- Check engine light on; on the 4T65-E, GM raises line pressure to maximum and freezes shift adapts
- Reverse or 3rd may be missingGM documented it on the 6T70 together with P0717 (US).
- Mistimed shifts or downshifts on the highway, because the computer doesn't trust input speed
Most common causes
- 1The input (turbine) speed sensor connector or wiringLoose, damaged or badly routed; on some 2009 Buicks (US), GM repaired and re-routed the transmission harness for P0716, P0717 and other codes.
- 2Debris from internal wearOn the 6T70 (Captiva Sport, Equinox and others), pieces of a broken wave plate affect the speed sensors and can set P0716 and P0717 along with clutch codes.
- 3A damaged clutchOn the 6T70 in the Impala, Equinox, Terrain, Enclave and others (US), GM replaces the 3-5-reverse clutch plates when there's no reverse or 3rd with P0716 and P0717.
- 4SoftwareAcura (2015–2018 TLX, 2016–2017 MDX) and Honda (2018–2019 Odyssey, Pilot) fix it with a transmission computer update (US).
- 5The sensor itself and, last, the computer
From most common and easiest to check to least common.
Follow these steps
Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.
Is reverse or any gear missing, or are there also ratio, pressure or solenoid codes?
In the internal-damage cases, these codes set together with P0776, P0756 or P2701. On the 6T70 (US), GM documented P0716 and P0717 with no reverse or 3rd.
It's guidance: a technician with a scan tool makes the final diagnosis.
See every step and resultShow
- Step 1. Is reverse or any gear missing, or are there also ratio, pressure or solenoid codes?Yes: «Suspect internal damage» · No: step 2
- Step 2. In P or N, does input speed on the scan tool equal engine rpm, and while driving, does it rise evenly with output speed without jumping?Yes: step 3 · No: step 4
- Step 3. Does the code come back when you drive under the same conditions in which it set?Yes: step 4 · No: «The signal is good»
- Step 4. With the scan tool connected, does the signal drop or jump when you move the sensor's harness and connector?Yes: «Connector or harness» · No: step 5
- Step 5. Is the sensor getting its power and ground (if it's Hall-effect), or does it produce an AC signal (if it's magnetic)?Yes: step 6 · No: «Power supply or ground»
- Step 6. Is the sensor tip clean, with no metal filings, the tone ring undamaged, and the sensor properly tightened?Yes: step 7 · No: «Filings, tone ring or a loose sensor»
- Step 7. Is there a software update for your VIN?Yes: «Update the software» · No: «Replace the input speed sensor»
Results
- Suspect internal damage. Check the pan: metal pieces point to internal damage, not the sensor. On the 6T70 (US), GM replaces the 3-5-reverse clutch plates when there's no reverse or 3rd with P0716 and P0717; on the 2016 Traverse, Acadia, Enclave and Equinox V6 it was the retaining ring of the input sensor's tone ring, out of its groove, with the sensor fine.
- The signal is good. If input speed follows the engine in P or N, rises evenly with output speed and the code doesn't come back when you drive under the same conditions, GM asks to stop testing so you don't replace parts needlessly.
- Connector or harness. If the signal drops or jumps when you move the harness, the problem is the connector or the wire: repair it before replacing the sensor. On some 2009 Buicks (US), GM repaired and re-routed the transmission harness for P0716, P0717 and other codes.
- Power supply or ground. Repair the power supply or ground before replacing the sensor: on the 2013 Silverado and Cheyenne with the 4L60E, GM fixed P0716 by repairing the sensor circuit and the module ground, and if the module pins had no continuity, it replaced the module and the sensor.
- Filings, tone ring or a loose sensor. Clean the filings off the tip, torque the sensor to spec and check the tone ring: a damaged or misaligned one gives a jumping signal. Debris and pieces come from internal wear, so check the pan too.
- Update the software. Ask for the reflash for your VIN and test again under the same conditions: that's how Acura and Honda (US) and Ram fixed it.
- Replace the input speed sensor. With the connector, power, tip and software ruled out, the sensor is the suspect. In transmissions with an internal sensor it comes in another part: on the 6R80, the lead frame. The computer comes last.
It's a range/performance code: the circuit responds, but the signal makes no sense. Compare input speed with output and engine speed on the scan tool; if the signal drops or jumps when you wiggle the harness, it's the connector or wiring. If it sets with P0717 and gears are missing, check the pan: metal pieces point to internal damage, not the sensor.
Carefully and only to the shop: the computer usually raises pressure and changes its strategy, and if the code comes from a damaged clutch, driving on makes it worse.
What carmaker bulletins say42 carmaker bulletins and the vehicles they nameShow
42 service bulletins published by the US NHTSA mention this code, mostly from Chevrolet, Pontiac, Buick, Acura, Honda (1999–2024 models). The repair they mention most: updating the computer software.
Vehicles with service bulletins for this code
- Acura MDX 2016–2019
- Chevrolet Cavalier 2000–2004
- Chevrolet Impala 2000–2016
- Buick Regal 2000–2016
- Acura TLX 2015–2018
- Honda Odyssey 2018–2019
- Buick Enclave 2008–2016
- GMC Acadia 2007–2016
On a downshift from 9th or 8th to 7th or lower, a TCM software miscalculation turns on the MIL with DTC P0716 (input shaft speed sensor range/performance).
Open the bulletin (PDF), page 4 ↗On a downshift from 9th or 8th to 7th or lower, a TCM software miscalculation turns on the MIL with DTC P0716 (input shaft speed sensor range/performance).
Open the bulletin (PDF), page 4 ↗Intermittent harsh or jerky upshifts under steady acceleration, or MIL on with DTC P0716.
Open the bulletin (PDF), page 3 ↗These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.
TSS parts for the transmissions in these bulletins
KIT REPARACION Y TESTEO Arnes EXTERNO (20 PIN) 4L80E, 4T40E, 4T80E, 4T65E, 4L60E, 4L70E, 1000
SENSOR DE VELOCIDAD DE ENTRADA (EXCEPTO VOLVO) 4T65E, MN7, MN3, M76
Different transmission? Pick it and we'll show its parts:
Find the part by its number on the exploded diagram: 4T65E · 6T70
Buying wholesale or own a parts store?
We'll send you a quote or tell you how to sell TSS in your area.