Check engine and A/T warning lights at startup with an engine inspection message and DTC P0722:00 in the TCM. The TCM control logic was changed to eliminate the concern.
Open the bulletin (PDF), page 1 ↗Code P0722: Output speed sensor no signal
The computer gets no signal, or an illogical one, from a transmission speed sensor. Without it, it doesn't know when to shift and usually goes into limp mode.
Speed sensors (input, turbine or output)
No power at the sensor
Only to the shop
What car do you have?
Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.
Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →
Symptoms
- The speedometer stays at 0 and the odometer may show dashes
- It starts off in a high gear or goes into limp modeThe 6R80 in the F-150 starts in 5th.
- Check engine and transmission warning lights at start-upMazda documented this on 2012–2014 Mazda3, CX-5 and Mazda6 in the US.
- Cruise control stops working
Most common causes
- 1No power at the sensorHall-effect sensors are fed by the computer, and an open wire leaves them with no signal.
- 2Open or shorted wires, or a connector with moisture, corrosion or damaged pins
- 3A failed output speed sensor (on the VW 01M it's G68, code 00281)
- 4On units with an internal sensor, the part that carries itOn the 6R80, Ford replaces the molded lead frame without replacing solenoids.
- 5SoftwareMazda fixed it by reprogramming the transmission module on those models.
- 6The computer, last; Hyundai specifically says not to replace the transmission for this code
From most common and easiest to check to least common.
Follow these steps
Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.
While driving, does output speed on the scan tool stay at or near 0?
GM sets P0722 when output speed stays at 70 rpm or less for 4 seconds while the vehicle moves. Note: on many newer cars the speedometer uses the wheels, so a working speedometer doesn't prove the sensor is good.
It's guidance: a technician with a scan tool makes the final diagnosis.
See every step and resultShow
- Step 1. While driving, does output speed on the scan tool stay at or near 0?Yes: step 3 · No: step 2
- Step 2. Does the code come back after you clear it and drive under the same conditions?Yes: step 3 · No: «The signal is good»
- Step 3. Is the sensor connector clean and tight, with no moisture, corrosion or damaged pins?Yes: step 4 · No: «Repair the connector»
- Step 4. Measured with a multimeter, are the wires OK, with no opens or shorts, and does it get power if it's a Hall-effect sensor?Yes: step 5 · No: «Wires or power supply»
- Step 5. Is there a software update for your VIN?Yes: «Update the software» · No: «Replace the output speed sensor»
Results
- The signal is good. If output speed rises and falls with road speed and the code doesn't return, GM asks to stop testing so you don't replace parts needlessly. If it comes back, check the connector and wires.
- Repair the connector. Clean or repair the connector and damaged pins, clear the code and test again. On the 01M, VW published bulletins with repair harnesses for its speed sensor faults.
- Wires or power supply. Repair the open or shorted wire before replacing the sensor. On Hall-effect sensors, if the power isn't there, the fault is the wiring or the computer, not the sensor; the computer comes last.
- Update the software. Ask for the transmission module reflash for your VIN, as Mazda did on those models, and read the codes again afterwards.
- Replace the output speed sensor. With the connector, wires and power OK, the sensor is the suspect (on the VW 01M, G68). On the 6R80 it's in the internal harness (lead frame), which Ford replaces without replacing solenoids; on Hyundai and Kia 6-speeds, the input and output sensors are a single part. Hyundai says not to replace the transmission for this code.
On Hall-effect sensors, measure the supply at the connector with the key on (GM wants 8.3–9.3 V on the 6T70): if it's missing, the fault is the wiring or the computer, not the sensor. GM sets the code when output speed stays at 70 rpm or less for 4 seconds while the vehicle is moving.
Only to the shop: without an output signal the transmission may start in a high gear or stay in one gear, and on some models it downshifts abruptly. If that happens, pull over carefully.
What carmaker bulletins say27 carmaker bulletins and the vehicles they nameShow
27 service bulletins published by the US NHTSA mention this code, mostly from Ford, Hyundai, Mazda, Mercury, Mercedes-Benz (1996–2019 models).
Vehicles with service bulletins for this code
- Mazda Mazda3 2012–2014
- Mazda CX-5 2013–2014
- Hyundai Accent 1996–2012
- Hyundai Elantra 1996–2011
- Ford Windstar 1999–2000
- Ford Taurus 2000–2008
- Lincoln Navigator 1999–2013
- Mercedes-Benz E207 2011–2017
Check engine and A/T warning lights at startup with an engine inspection message and DTC P0722:00 in the TCM. The TCM control logic was changed to eliminate the concern.
Open the bulletin (PDF), page 1 ↗Check engine and A/T warning lights at startup with an engine inspection message and DTC P0722:00 in the TCM. The TCM control logic was changed to eliminate the concern.
Open the bulletin (PDF), page 1 ↗Check engine and A/T warning lights at startup with an engine inspection message and DTC P0722:00 in the TCM. The TCM control logic was changed to eliminate the concern.
Open the bulletin (PDF), page 1 ↗These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.
TSS parts for the transmissions in these bulletins
Sensor Velocidad Salida 3 Pines 2007/UP 6F50 6F55
Conector del Casco (Plastico) (# Impreso 6L2P-7H585-AA) 6R60 6R80
Different transmission? Pick it and we'll show its parts:
Find the part by its number on the exploded diagram: 6T70 · 6R80
Buying wholesale or own a parts store?
We'll send you a quote or tell you how to sell TSS in your area.