Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
System: Speed sensors (input, turbine or output)

Code P0717: Input/turbine speed sensor no signal

The computer gets no signal, or an illogical one, from a transmission speed sensor. Without it, it doesn't know when to shift and usually goes into limp mode.

What's failing

Speed sensors (input, turbine or output)

Most common cause

The input (turbine) speed sensor connector or wiring

Can I drive with this code?

To the shop, carefully

Diagnosis for your car

What car do you have?

Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.

Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →

Symptoms

  • Harsh or mistimed shifts, and the torque converter stops locking up
  • Limp mode with high pressureFord's 6R80 defaults to 5th with maximum line pressure, and GM's 4T65-E raises line pressure and freezes its adaptive learning.
  • No reverse and no 3rdGM documented this with P0716 and P0717 on 6T70 and 6T75 units (US).
  • Check engine light on; the speedometer usually still works

Most common causes

  1. 1The input (turbine) speed sensor connector or wiringLoose, broken or corroded.
  2. 2Metal debris on the sensor tip, or a failed sensor
  3. 3On units with an internal sensor, the part that carries itOn the 6R80, the lead frame, its connector and harness.
  4. 4Internal damage the sensor can no longer readOn 6T70 and 6T75 units (2016 Equinox, Terrain, Impala, Acadia in the US), GM replaced the 3-5-R clutch plates, and in the 6T family pieces of a broken plate can affect the speed sensors.
  5. 5The computer or its software, last; Hyundai says not to replace the transmission for its input and output speed sensor codes

From most common and easiest to check to least common.

Step-by-step diagnosis

Follow these steps

Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.

Step 1

Is reverse or any gear missing, or are there also ratio, pressure or solenoid codes?

GM documented it with P0716 and P0717 on the 6T70 and 6T75 with no reverse or 3rd (US), and Ford on the 6F50 and 6F55 (2015–2016 Edge and Explorer) with no reverse, 3rd or 5th, with P0715, P0717, P0756 and P2701.

It's guidance: a technician with a scan tool makes the final diagnosis.

See every step and resultShow
  1. Step 1. Is reverse or any gear missing, or are there also ratio, pressure or solenoid codes?Yes: «Suspect internal damage» · No: step 2
  2. Step 2. While driving, does the scan tool show 0 rpm input (turbine) speed while the output does show speed?Yes: step 4 · No: step 3
  3. Step 3. Does the code come back when you drive under the same conditions in which it set?Yes: step 4 · No: «The signal is good»
  4. Step 4. Are the connector and harness OK, with no pushed-out, loose or bent terminals, moisture, corrosion or pinched wires?Yes: step 5 · No: «Connector or harness»
  5. Step 5. Is the sensor getting its power and ground (if it's Hall-effect), or does it produce an AC signal (if it's magnetic)?Yes: step 6 · No: «Power supply or ground»
  6. Step 6. Is the sensor tip clean, with no metal filings, and the sensor properly tightened?Yes: «Replace the input speed sensor» · No: «Filings or a loose sensor»

Results

  • Suspect internal damage. If gears are missing, the sensor may be fine. GM replaced the 3-5-R clutch plates on the 6T70 and 6T75 (US), and on 2016 models the retaining ring of the input sensor's tone ring was out of its groove. Ford, on the 6F50 and 6F55, replaces the sensor along with the direct clutch parts and cleans metal particles out of the transmission.
  • The signal is good. If input speed follows the engine in P or N, rises evenly with output speed and the code doesn't come back when you drive under the same conditions, GM asks to stop testing so you don't replace parts needlessly.
  • Connector or harness. Repair pushed-out, loose or bent terminals, moisture or corrosion and pinched wires before replacing the sensor. On some 2009 Buicks (US), GM repaired and re-routed the transmission harness for P0716, P0717 and other codes.
  • Power supply or ground. Repair the power supply, wires or ground before replacing the sensor: on the 2013 Silverado and Cheyenne with the 4L60E, GM fixed it by repairing the sensor circuit and the module ground, and if the module pins had no continuity, it replaced the module and the sensor.
  • Filings or a loose sensor. Clean the filings off the tip and torque the sensor to spec. Debris comes from wear inside the transmission, so check the pan too: metal pieces point to internal damage, not the sensor.
  • Replace the input speed sensor. With the connector, power and tip OK, the sensor is the suspect. On the 6R80 it comes in the lead frame, and on Hyundai and Kia 6-speeds the input and output sensors are a single part replaced with the valve body harness. The computer comes last; Hyundai says not to replace the transmission for this code.
Diagnostic tip

Watch input (turbine) speed on the scan tool while driving: if it reads 0 rpm while the vehicle moves and the output sensor does show speed, check power, wiring and connector first. If reverse and 3rd are also missing on a GM 6-speed, suspect internal damage too, not just the sensor.

Can I drive with this code?

To the shop, carefully: the transmission usually stays in one gear with high pressure, pulls away slowly and engagements hit hard. If reverse or 3rd is also missing, stop using it.

What carmaker bulletins say35 carmaker bulletins and the vehicles they nameShow

35 service bulletins published by the US NHTSA mention this code, mostly from Ford, Chevrolet, Buick, Pontiac, GMC (1996–2021 models).

Vehicles with service bulletins for this code

  • Chevrolet Impala 2000–2016
  • Buick Regal 2000–2016
  • Hyundai Elantra 1996–2011
  • Buick Enclave 2008–2016
  • GMC Acadia 2007–2016
  • Hyundai Tiburon 1997–2003
  • Chevrolet Cavalier 2000–2004
  • Ford Taurus 2008–2016
Bulletin PIP5084 · 2013
GMC Sierra 2013 · GMC Sierra Denali 2013 · Chevrolet Express 2013 · Chevrolet Silverado 2013

Harsh shift or MIL with P0717 in the TCM. Check circuit 1984 and TCM pin continuity; depending on the result, replace the TCM and input speed sensor, or the sensor only.

Open the bulletin (PDF), page 1 ↗
Bulletin 050604073 · 2005
Saturn Ion 2006 · Chevrolet Cobalt 2006 · Chevrolet Hhr 2006

Check engine light, usually with no driveability symptoms, with DTCs P0128, P0326, P0420, P0717, P2431 on the L61 engine. Follow SI and, if needed, reprogram the ECM.

Bulletin 16-NA-013 · 2016
GMC Terrain 2016 · Chevrolet Equinox 2016 · Chevrolet Impala 2016 · Buick Lacrosse 2016

Procedure to replace the 3-5-reverse clutch plates for no reverse, no third, and DTCs P0716 and P0717.

Open the bulletin (PDF), page 1 ↗

These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.

TSS parts for the transmissions in these bulletins

Buy in

Different transmission? Pick it and we'll show its parts:

See parts →

Find the part by its number on the exploded diagram: 6T70 · 4T65E

Related codes

← See all codes

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.