Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
System: Transmission module power

Code P0882: TCM power input signal low

The voltage reaching the transmission module is low, high or drops out. On Chrysler it's measured at the transmission relay output.

What's failing

Transmission module power

Most common cause

The battery

Can I drive with this code?

Slowly and only to the shop

Diagnosis for your car

What car do you have?

Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.

Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →

Symptoms

  • Limp modeThe transmission stays in one gear (2nd on Chrysler 4-speeds such as the Journey 2.4, Avenger, Liberty or Nitro; 3rd on the 62TE and RFE units). Mazda also goes into limp mode.
  • Check engine light with other transmission codes at the same time (P0846, P0869, P0871, P0876, P0988 on Chrysler) that, per Chrysler, clear once P0882 is fixed and don't indicate an internal failure
  • The fault shows up when cranking or switching on, and sometimes clears after a restart
  • If the battery or alternator is the cause, the engine may also be hard to start

Most common causes

  1. 1The batteryLoose or corroded terminals, or a weak battery that drops voltage while cranking; Mazda has a bulletin fixed just by tightening the terminals.
  2. 2The alternator, if it undercharges (if it overcharges, P0883 sets)
  3. 3A blown or poorly seated fuse and, on Chrysler, the transmission control relay or its circuit
  4. 4A chafed wire, a wet splice, a bad ground or badly installed accessories drawing power from the transmission circuit; on the 2023 Compass, Chrysler found the harness rubbing against the computer
  5. 5On Chrysler, a shorted component inside the transmission (solenoid pack, range sensor or pressure solenoid) pulling down the relay voltage
  6. 6Software and, last, the computerChrysler released a reflash for P0883 on the 2023 Compass.

From most common and easiest to check to least common.

Step-by-step diagnosis

Follow these steps

Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.

Step 1

Are there system voltage (P0562, P0563), communication (U0101) or fuse module codes?

Read the codes in every module. The other transmission codes that set with P0882 on Chrysler (P0846, P0869, P0871, P0876, P0988) clear once it's fixed and don't indicate an internal fault.

It's guidance: a technician with a scan tool makes the final diagnosis.

See every step and resultShow
  1. Step 1. Are there system voltage (P0562, P0563), communication (U0101) or fuse module codes?Yes: «Fix those codes first» · No: step 2
  2. Step 2. Is the code present now, not just in history?Yes: step 3 · No: «Intermittent or history fault»
  3. Step 3. Does the battery pass a load test, with clean, tight terminals, and does the alternator charge properly?Yes: step 4 · No: «Battery or alternator»
  4. Step 4. Are there aftermarket alarms, stereos or lights drawing power from the computer or the transmission circuit?Yes: «Poorly installed accessory» · No: step 5
  5. Step 5. Tested with a meter or test lamp, are the fuses good?Yes: step 6 · No: «Open fuse»
  6. Step 6. Is full power reaching the transmission module?Yes: step 7 · No: «Relay or power feed»
  7. Step 7. Are the wiring, grounds and computer terminals OK, with no shorts to ground, wet splices or chafing?Yes: «Software, and the computer last» · No: «Wire, splice or ground»

Results

  • Fix those codes first. System voltage, communication or fuse module codes are fixed before P0882: look them up in this tool and follow their diagnosis. Then clear the codes and test again.
  • Intermittent or history fault. Wiggle-test the harness and connectors with the scan tool connected, and review the event data. If you find nothing, clear the code and check again if it returns.
  • Battery or alternator. Tighten the terminals, charge or replace the battery and repair the charging system, then clear the codes and test again. Ford asks to fix any low voltage before replacing the module.
  • Poorly installed accessory. Remove or properly install the alarm, stereo or lights drawing power from the transmission circuit: Chrysler asks to check them before diagnosing. Then clear the codes and test again.
  • Open fuse. No power is getting through: replace the fuse and find the short that blew it before testing further.
  • Relay or power feed. If switched voltage now equals battery voltage with another relay, the transmission control relay was bad: replace it. If the supply at the module is still low, there's an open or resistance between the battery and the module: repair the wire, connector or splice.
  • Wire, splice or ground. Repair and protect the chafed or shorted wire, the corroded or wet splice, or the ground. On Chrysler, also check whether something inside the transmission pulls the voltage down: the rebuilding industry found shorted solenoid packs on the 545RFE, 42RLE and 62TE.
  • Software, and the computer last. With every circuit and terminal OK, look for a reflash for your model first; then the computer is replaced and programmed, with its learning procedure (Quick Learn on Chrysler). Clear the codes and run the carmaker's verification test.
Diagnostic tip

On Chrysler, swap the transmission control relay for a known-good one and read switched battery voltage on the scan tool: if it now matches battery voltage, the relay was the fault. On Mazda, the VPWR scan value must equal battery voltage; on the Ford PowerShift, the module needs more than 10.5 V at its connector.

Can I drive with this code?

Slowly and only to the shop: the transmission stays in a single gear and, if the battery or alternator is the problem, the car may not restart.

What carmaker bulletins say4 carmaker bulletins and the vehicles they nameShow

4 service bulletins published by the US NHTSA mention this code, mostly from Mazda, Jeep (2023–2023 models).

Vehicles with service bulletins for this code

  • Jeep Compass 2023
  • Mazda Unknown
  • Mazda Mazda
Bulletin Battery · 2021
Mazda Mazda

Skyactiv: MIL on with P0882:00 (TCM power supply voltage low). Loose battery terminals may be the cause: torque them to spec, then erase the DTCs.

Open the bulletin (PDF) ↗
Bulletin MULTI-MODELS 14 · 2016
Mazda Unknown

Skyactiv: MIL on with P0882:00 (TCM power supply voltage low). Loose battery terminals may be the cause: torque them to spec, then erase the DTCs.

Open the bulletin (PDF) ↗
Bulletin 0814123 · 2023
Jeep Compass 2023

Transmission harness rubbing a sharp PCM edge: MIL with P0882, P0883, P0983 or P0707 and limp mode. Fix is installing foil tape and possibly repairing the harness.

Open the bulletin (PDF), page 3 ↗

These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.

TSS parts for this code

Pick your transmission to see the TSS parts that fit it, or open all parts of this type:

See parts →

Related codes

← See all codes

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.