Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

P0882, P0883 and P0884: TCM power input diagnosis

TSS editorial team · · 8 min read

Technician operating a diagnostic scanner above an open engine bay checking TCM power supply and voltage codes P0882 and P0883
In short
  • P0882 is low voltage on the transmission module supply and P0883, high voltage. On Chrysler they measure the transmission relay output, not the battery, and P0884 means "power up at speed".
  • The typical symptom is limp mode: Chryslers stay in 2nd (4-speeds) or 3rd (62TE and RFE), sometimes with other transmission codes that don't mean an internal fault.
  • The causes go from simple to complex: battery terminals, alternator, fuses, the relay, wiring and grounds, badly installed accessories, and on Chrysler a shorted component inside the transmission.
  • Diagnosis follows that order and leaves the computer for last, after looking for a reflash.
  • It's not for the highway: the transmission stays in one gear and the voltage problem can leave you unable to start.

Codes P0882, P0883 and P0884 are about the transmission module (TCM) supply, not a part of the transmission. So before replacing the module or the transmission, check the battery, alternator, fuses, relay and wiring. Here we explain what they mean on each make and how to diagnose them step by step. What the module is and where it sits are in our TCM transmission module guide.

What do P0882, P0883 and P0884 mean?

The generic name for P0882 is "TCM power input signal low", P0883 is "high" and P0884, "intermittent". But each make measures something different:

Chrysler, Dodge, Jeep and RAM (41TE, 62TE, 40TES, 42RLE, 45RFE, 545RFE, 68RFE; 2008 on)P0882: the transmission control relay output reads under 3 V when the computer turns it on. P0883: it reads over 3 V before it's turned on. P0884 isn't "intermittent": Chrysler calls it "power up at speed", it's informational and doesn't put the transmission in limp mode
Chrysler before 2008Used other numbers for the same fault: P0888 and P0891 (2002 to 2008) and P1765 to P1768 on pre-2001 41TEs
Mazda (SKYACTIV 6-speed)P0882: TCM supply voltage low, 8 to 10.5 V or less depending on fluid temperature. P0883: high, 18 V or more for 5 seconds
Ford (Focus PowerShift DPS6)P0882: the TCM supply must be above 10.5 V; Ford checks it together with the 25 A F15 fuse
GM (Allison in HD pickups)P0882: under 8 V at 0 °C for 5 of 7 seconds; the limit runs from 5 V at −60 °C to 9 V at 20 °C
Nissan, Hyundai and KiaThey don't use P0882 for this: Nissan uses P1701 on its CVTs, and Hyundai and Kia use P0880, with the transmission stuck in 4th

We explain Chrysler's other own codes in our Dodge, Jeep and Chrysler code guide.

P0882 and P0883 symptoms

  • Limp mode: the transmission stays in one gear. On Chrysler 4-speeds (Journey 2.4, Avenger, Liberty, Nitro, PT Cruiser) it stays in 2nd; on the 62TE and RFE units, in 3rd. Mazda also goes into emergency mode.
  • Check engine light on, sometimes with other transmission codes at the same time (P0846, P0869, P0871, P0876, P0988 on Chrysler). According to Chrysler, fixing P0882 clears those too, and they don't mean an internal transmission fault.
  • The fault shows up when cranking or at key-on, and sometimes goes away after switching off and restarting.
  • With P0884 alone on a Chrysler: it drops to 2nd or 3rd for a moment and then goes back to normal, because the computer briefly lost power while driving.

What causes these codes?

From simplest to most complex, according to the makers' manuals and bulletins:

  • The battery: loose or corroded terminals, or a weak battery whose voltage sags while cranking. Mazda has a bulletin saying P0882 can be caused just by loose terminals.
  • The alternator: undercharging sets P0882; overcharging sets P0883 (Mazda).
  • A blown or poorly seated fuse on the module's supply.
  • On Chrysler, the transmission control relay (in the TIPM fuse module or the fuse box) or its circuit.
  • A chafed wire, a splice with water or corrosion, or a bad ground. On the 2023 Jeep Compass, Chrysler found the harness rubbing against the edge of the computer (P0882, P0883).
  • Badly installed alarms, stereos or lights that draw power from the transmission circuit; Chrysler says to check them before diagnosing.
  • On Chryslers, a shorted component inside the transmission: the solenoid pack, the range sensor or the pressure solenoid can pull the relay voltage. For P0883, Chrysler unplugs them one by one; for P0882, the rebuild industry has found shorted solenoid packs on the 545RFE, 42RLE and 62TE, even though the factory manuals don't mention it.
  • The software or the computer, last: Chrysler released a reflash for P0883 on the 2023 Compass.

Step-by-step diagnosis

This order comes from the Chrysler (62TE and 40TES), Mazda, Ford and GM procedures. You need a scan tool, a multimeter and a test light:

  • Step 1. Read codes from every module and the freeze frame. Note any system voltage codes (P0562, P0563), communication codes (U0101) or fuse module codes: those come first.
  • Step 2. Check whether the code is current or history. On Chrysler, a "starts since set" counter at 0 means it's current; if it's history, go to step 13.
  • Step 3. Battery: tighten and clean the terminals (Mazda calls for 22 to 30 N·m), charge it and load test it.
  • Step 4. Charging system: check alternator voltage with the engine running. Undercharging explains P0882; overcharging, P0883.
  • Step 5. Look for add-on accessories (alarms, stereos, lights) drawing power from the computer or transmission circuit.
  • Step 6. Fuses: test them with a multimeter or test light, not just by looking (Ford 25 A F15; Mazda 15 A AT).
  • Step 7. On Chrysler: swap the transmission control relay for a known-good one and read "switched battery" voltage on the scan tool. If it now shows battery voltage, the relay was bad.
  • Step 8. Measure the supply at the module: on Ford, over 10.5 V at its connector; on Mazda, the VPWR scan data must match the battery; on Chrysler, the test light must glow bright on both relay inputs.
  • Step 9. Check the wiring: opens, shorts to ground (on Chrysler, over 100 kΩ is fine), corroded or wet splices and rubbing against the body or the computer.
  • Step 10. Check the computer's grounds and terminals: corrosion, damage or pushed-out pins.
  • Step 11. For P0883 on Chrysler only: with the circuit unplugged from the computer, unplug the solenoid pack, then the range sensor, then the pressure solenoid. The one that drops the voltage below 0.5 V when unplugged is the shorted one.
  • Step 12. Look for reflashes (bulletins) for your model before replacing the computer.
  • Step 13. If it's intermittent or history: wiggle test the harness and connectors and check the event data. Only when everything above passes is the computer replaced and programmed, with its relearn. Then clear the codes and run the maker's verification test.

What your results mean

Loose terminals or a weak battery that fails the load testVoltage drops and the module detects it: tighten the terminals, charge or replace the battery, clear the codes and retest
The alternator under- or overchargesP0882 if it undercharges, P0883 if it overcharges: repair the charging system first
Open fuseNo supply: replace it and find the short that blew it
On Chrysler, with a different relay the switched voltage equals battery voltageThe transmission control relay was bad: replace it and run the verification test
Low supply at the module (Ford 10.5 V or less; Mazda VPWR different from the battery)Open or resistance between the battery and the module: repair the wire, connector or splice
Output wire shorted to groundChafed wire (as on the 2023 Compass): splice it, protect it and retest
P0883: voltage drops when you unplug the solenoid pack, range sensor or pressure solenoidThat part is shorted: replace it
All circuits and terminals are fineSoftware or computer: reflash first, then replace and program it with its relearn
Only P0884, it drops to 2nd or 3rd and then returns to normalThe computer briefly lost power: check supplies, ignition and grounds for intermittents. It isn't a transmission fault

Can I drive with code P0882?

Slowly and only to the shop. On Chryslers, the computer turns off the relay and the transmission stays in one gear: the car moves but doesn't shift, and Mazda goes into emergency mode. Also, if the cause is the battery or alternator, it can leave you unable to start. With P0884 alone, Chrysler doesn't put the transmission in limp mode. More on limp mode in why won't my automatic transmission shift?.

P0882 myths

  • "P0882 means replace the module": no. Chrysler checks the relay, fuses, wiring and terminals before the computer; Ford says to fix low voltage before replacing the TCM, and Mazda, to tighten the battery terminals.
  • "It sets when the battery drops below 9 V": each make has its own limit. On Chrysler the battery isn't even what's measured, but the relay output (3 V); Ford uses 10.5 V, Mazda 8 to 10.5 V and GM 5 to 9 V depending on temperature.
  • "P0884 is intermittent power" on a Dodge: Chrysler calls it power up at speed, it's informational and doesn't put the transmission in limp mode.
  • "The transmission is damaged" because other transmission codes show up: Chrysler says they don't mean an internal fault.

After the repair

Clear the codes and run the maker's verification test; on Mazda, drive at least 5 seconds in D or R. If you replaced the computer, it has to be programmed and relearned (Quick Learn on Chrysler). If communication codes come with P0882, see the U0101 code guide, and if the solenoid pack turned out to be shorted, our transmission solenoids guide explains how to test them. If P0705 or P0707 also show up, see the range sensor codes guide.

See TSS parts for Chrysler transmissions

TSS parts for Chryslers with P0882 and P0883

When diagnosis finds a shorted component inside the transmission, these are the TSS parts for Chrysler transmissions (their failures are in our 41TE, A604 and 62TE and 45RFE and 545RFE guides):

41TE / A604 (Journey 2.4, Caravan, Avenger, Stratus)solenoid pack, range sensor, pressure solenoid and pressure sensor
62TE (Journey 3.6, Town & Country, Grand Caravan)23-pin solenoid pack
42RLE (Liberty, Nitro, Wrangler, Dakota)solenoid pack and pressure solenoid
45RFE, 545RFE and 68RFE (RAM, Durango, Grand Cherokee)solenoid pack and pressure sensor

Confirm your transmission in the Transmisiones Veinte 07 transmission finder before ordering: the solenoid pack connector changes by year.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • What does code P0882 mean?

    Transmission control module (TCM) power input signal low. On Chrysler, Dodge, Jeep and RAM it means the transmission control relay output reads under 3 V when the computer turns it on; on Mazda, Ford and GM, that the voltage reaching the module is below its limit.

  • Is P0882 the battery?

    Often, yes: loose or corroded terminals, a weak battery or an undercharging alternator. Mazda has a bulletin that fixes it just by tightening the terminals. But it can also be a fuse, the relay, a chafed wire or, on Chrysler, a shorted component inside the transmission.

  • What does code P0883 mean?

    Module power input signal high. On Chrysler, the relay output shows voltage before the computer turns it on; on Mazda, 18 V or more for 5 seconds, usually from an overcharging alternator.

  • What does P0884 mean on a Dodge?

    Chrysler calls it power up at speed: the computer briefly lost power while driving. It's an informational code and doesn't put the transmission in limp mode; check supplies and grounds for intermittents.

  • Can I drive with code P0882?

    Slowly and only to the shop. The transmission stays in one gear (2nd or 3rd on Chryslers) and, if the cause is electrical, the car may not restart.

  • Does P0882 mean replacing the transmission module?

    It's almost never the first step. Chrysler, Ford and Mazda check the battery, alternator, fuses, relay, wiring and terminals first, and look for a reflash. The module is replaced and programmed only when all of that checks out.

  • Can solenoids cause P0882?

    On Chryslers, yes. For P0883, Chrysler unplugs the solenoid pack, range sensor and pressure solenoid one by one to find the shorted one, and the rebuild industry has found shorted solenoid packs setting P0882 on the 545RFE, 42RLE and 62TE.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.