Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
System: Transmission module power

Code P0884: TCM power input signal intermittent

The voltage reaching the transmission module is low, high or drops out. On Chrysler it's measured at the transmission relay output.

What's failing

Transmission module power

Most common cause

A momentary power loss to the computer

Can I drive with this code?

On a Chrysler with only this code, the transmission doesn't go into limp mode and can be driven carefully

Diagnosis for your car

What car do you have?

Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.

Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →

Symptoms

  • On ChryslersThe transmission stays in 2nd (3rd on RFE units) for a moment and then returns to normal, because the computer briefly lost power while driving.
  • If it's the only code on a Chrysler, there may be no other symptomsIt's informational and doesn't trigger limp mode.
  • On the 2012–2013 Ford Focus (US), Ford listed it with intermittent or delayed engagement out of P, D or R, noise at start and hard or no start
  • Check engine light on or the code stored in history

Most common causes

  1. 1A momentary power loss to the computerChrysler points to the fused battery feed, the ignition feed or the grounds with an intermittent connection.
  2. 2Loose battery terminals or a weak battery; on the Mazda 4-speed (FN4A-EL), Mazda calls it "battery voltage low"
  3. 3Connectors or wires with an intermittent contact that fails with movement
  4. 4A "rolling restart"Chrysler explains that if the engine is shut off and restarted while rolling and D is selected before the computer finishes starting up, the code can set.

From most common and easiest to check to least common.

Step-by-step diagnosis

Follow these steps

Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.

Step 1

Did you shut off and restart the engine while rolling, and shift into D right away?

Chrysler calls it "power up at speed": it sets if the computer starts up with the vehicle in a forward gear above about 32 km/h (20 mph).

It's guidance: a technician with a scan tool makes the final diagnosis.

See every step and resultShow
  1. Step 1. Did you shut off and restart the engine while rolling, and shift into D right away?Yes: «Power up at speed» · No: step 2
  2. Step 2. Are the battery terminals clean and tight, and does the battery pass a load test?Yes: step 3 · No: «Battery first»
  3. Step 3. With the scan tool connected, does the code or the reading change when you move the computer's harness and connectors?Yes: «Bad contact» · No: step 4
  4. Step 4. Are the computer's fused battery feed, ignition feed and grounds OK, with no loose terminals or corrosion?Yes: «Check the event data» · No: «Computer power feed or ground»

Results

  • Power up at speed. If that's what happened, the code explains itself and isn't a transmission fault: clear it. With only this code, a Chrysler doesn't go into limp mode.
  • Battery first. Tighten and clean the terminals, and charge or replace the battery, then clear the code and test again.
  • Bad contact. If it changes when you move the harness, that's where the fault is: find the damaged connector or section and repair it. The same bad contact can leave you without shifts or unable to start.
  • Computer power feed or ground. Repair the power feed or ground with the bad connection: the computer loses power for an instant, which is why the transmission stays in 2nd (3rd on RFE units) for a moment and then returns to normal.
  • Check the event data. If everything passes, review the event data next time it sets and repeat the wiggle test. It isn't a transmission fault, but don't let it go: the same bad connection can leave you without shifts or unable to start.
Diagnostic tip

Chrysler calls it "power up at speed": it sets when the computer starts up with the vehicle in a forward gear above about 32 km/h (20 mph). It isn't a transmission fault: check the computer's power, ignition and ground circuits with a wiggle test on the harness.

Can I drive with this code?

On a Chrysler with only this code, the transmission doesn't go into limp mode and can be driven carefully; still, check the power feed soon, because the same bad connection can leave you without shifts or unable to start.

What carmaker bulletins say1 carmaker bulletin and the vehicles they nameShow

1 service bulletin published by the US NHTSA mention this code, mostly from Ford (2012–2013 models).

Vehicles with service bulletins for this code

  • Ford Focus 2012–2013
Bulletin ASI-44686 · 2014
Ford Focus 2012–2013

Intermittent or delayed engagement out of Park, Drive or Reverse, noise at start, intermittent, hard or no start, with or without DTCs such as P0805, P0850, P0884 and P2831.

Open the bulletin (PDF) ↗

These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.

TSS parts for this code

Pick your transmission to see the TSS parts that fit it, or open all parts of this type:

See parts →

Related codes

← See all codes

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.