Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

P0776, P0777, P0796, P0965: pressure solenoid B and C

TSS editorial team · · 13 min read

Precision hydraulic worm tracks of an automatic transmission valve body casting for pressure control solenoid B and C codes P0776 and P0796
In short
  • P0776, P0777 and P0778 are pressure control solenoid "B" codes; P0796, P0797 and P0798, solenoid "C"; and P0965 to P0967, the "B" circuit. Which solenoid each letter is depends on the make.
  • On 6-speed Chevrolets, B controls the 3-5-reverse clutch and C the 4-5-6. Nissan CVTs have two "B"s: P0776 is the secondary pressure solenoid and P0965 the primary.
  • Performance codes (P0776, P0777, P0796) aren't always the solenoid: GM and Nissan US bulletins replaced pistons, wave plates, hubs, valve bodies and CVT belts.
  • P0778, P0798, P0962, P0963, P0966 and P0967 are electrical: wire, connector, coil or computer. Chevrolet's P0965 doesn't turn on the check engine light.
  • The diagnosis order: other codes, fluid level, line pressure, a solenoid test against your transmission's value, valve body and clutches, and the computer last.

P0776, P0777 and P0778 are the pressure control solenoid "B" codes, and P0796, P0797 and P0798 the "C" codes; P0965 to P0967 are the "B" control circuit. They're among the most searched on the Chevrolet Cruze, Sonic, Trax and Silverado and on Nissan CVTs. Here's which solenoid B and C are on each make, why most of the time it isn't the solenoid, how to diagnose them step by step, the makers' test values and the matching TSS parts. Solenoid "A", the line pressure solenoid, has its own guide: P0745, P0746 and P0748.

What do P0776, P0777, P0796 and P0965 mean?

P0776Pressure control solenoid B: performance or "stuck off". The computer commanded a pressure or a clutch, and the result doesn't match
P0777Solenoid B "stuck on": the clutch applies when it shouldn't
P0778 and P0779Solenoid B: electrical fault. On Nissan, P0778 is a short to ground and P0779 an open circuit or a short to voltage
P0796, P0797 and P0798The same for solenoid C: performance or stuck off, stuck on and electrical fault
P0965Solenoid B: control circuit range or performance. On Chevrolet it's an electrical fault that doesn't turn on the check engine light; on Nissan CVTs, primary pulley pressure
P0966 and P0967Solenoid B control circuit: low or high voltage
P0962 and P0963Control circuit of solenoid A, the line pressure solenoid: low or high voltage

Performance codes (P0776, P0777, P0796, P0797 and Nissan's P0965) compare what the computer commanded with what happened: the solenoid can cause them, but so can the valve body, a clutch or line pressure. Electrical codes (P0778, P0798, P0962, P0963, P0966 and P0967) come from a wire, a connector, the coil or the computer; Honda points out that a mechanical failure doesn't cause them.

Which solenoid is B and C on each make?

The letter changes by maker, and on some transmissions it doesn't exist at all:

Chevrolet Cruze, Sonic, Trax, Equinox and Malibu (6T40 and 6T45)B: pressure solenoid 2, which feeds the 3-5-reverse clutch. C: pressure solenoid 3, for the 4-5-6 clutch and the low and reverse clutch. Both sit inside the transmission module
Chevrolet Cheyenne, Silverado, Tahoe and Suburban (6L80 and 6L90); Traverse, Acadia and Captiva Sport V6 (6T70 and 6T75)B: 3-5-reverse clutch. C: 4-5-6 clutch and low and reverse brake
2007 to 2012 Nissan Sentra, 2008 to 2014 X-Trail, 2007 to 2012 Altima 2.5 and 2012 to 2014 Juke (JF011E CVT)Only the secondary pressure B solenoid: P0776 and P0778
2013 to 2019 Nissan Sentra and Note (JF015E CVT)Only the primary pressure B solenoid: P0965, P0966 and P0967; it doesn't use P0776
2015 to 2022 Nissan X-Trail, 2020-on Sentra, 2013-on Altima, 2013 to 2020 Pathfinder and 2015 to 2017 Juke (JF016E and JF017E CVTs)Both: the secondary pressure solenoid (P0776, P0778 and P0779) and the primary pressure solenoid (P0965, P0966 and P0967)
2020-on Nissan Kicks and VersaNissan lists P0776 and P0965 in its US bulletins; we didn't find which pulley each one checks
2006 to 2012 Toyota RAV4 and 2007 to 2009 Camry 2.4 (U241E and U250E)B: the SL2 solenoid. C: SL3, on the 5-speed
Toyota 6-speed Camry, 2013 to 2018 RAV4, Sienna and Highlander (U660E and U760E)B: SL2, which works in 4th to 6th. C: SL3, in 2nd and 6th
5-speed Honda Civic, Accord, CR-V, Odyssey, Pilot, City and FitB and C: the clutch linear solenoids B and C
Jeep Compass and Patriot, Dodge Caliber and Mitsubishi Lancer and Outlander (CVT)B: the secondary pressure solenoid
Ford Explorer and Mustang (5R55W and 5R55S)B and C: the PCB and PCC solenoids. With P0778, 2nd and 5th are missing
Volkswagen Jetta, Golf and Beetle 2.5 (09G) and 2010 to 2013 Mazda 3VW tied P0776 and P0796 to a broken wire to its N216 and N217 solenoids; the Mazda uses P0777 and P0778 for its B solenoid

Hyundai and Kia 6-speed automatics (one code per solenoid), Chrysler's 41TE, 62TE and RFE units, and Ford's 6R80 and 6F35, which only have the line pressure "A", don't use these codes. Neither do the Corolla 1.8 or the 4-speed 2012 to 2019 Versa, March, Tiida and Tsuru. More models in our guides to which transmission your Nissan has and Chevrolet.

P0776, P0777 and P0796 symptoms

  • The check engine light on. On Chevrolet, P0776 and P0796 turn it on the first trip they're detected; Chevrolet's P0965 doesn't turn it on.
  • Shifts that flare or slip, or that feel harsh: the computer raises pressure to maximum to protect the transmission.
  • Missing gears. With P0776, a 2011 Cruze (6T40) holds reverse and 2nd; on the second-generation 2013 Cruze 1.4 turbo, the transmission drops to neutral if the car is moving fast. With P0796, the 6T40 holds reverse and 3rd.
  • On a Nissan CVT with P0776: a jolt when shifting into gear, slow starts and acceleration, no converter lock-up, and the speed won't climb.
  • On Explorers with the 5R55W, P0778 leaves the transmission without 2nd and 5th.

If the transmission slips with no solenoid codes, check the incorrect ratio codes too.

What causes these codes?

The bulletins the makers published in the US almost never replace just the solenoid:

Chevrolet Cruze, Sonic, Trax and Malibu (6T40 and 6T45), P0776The 3-5-reverse clutch wave plate and piston: GM says to inspect them before replacing the module. Only on some early-2011 6T40s was it the solenoid inside the module
2007 to 2009 Chevrolet Traverse, Acadia, Equinox and Malibu V6 (6T70 and 6T75), P0776A broken 3-5-reverse clutch wave plate. GM replaced the plate, the pump filter and the solenoid filter plate, and said not to replace the module unless the diagnosis calls for it
2006 to 2009 Silverado, Tahoe and Suburban (6L80 and 6L90), P0776A cracked 1-2-3-4 and 3-5-reverse clutch housing
Silverado and Tahoe with the 6L80 and 6L90 (2006 to 2012), P07964-5-6 clutch damage; GM says to disassemble and inspect the pump too
2015 and 2016 Silverado 2500, Tahoe and Suburban (6L80 and 6L90), P0796A broken 4-5-6 clutch hub. GM made clear the module isn't the cause and shouldn't be replaced
2020 and 2021 Silverado 1500 and Colorado 8-speeds, P0796If the pan is clean, GM replaces the valve body
Nissan Altima, Sentra, Kicks, Versa, Note and Juke CVTs, P0776 or P0965Nissan removes the valve body and inspects the belt: if it's fine, it replaces only the valve body; if it slipped, the belt and pulleys, the pump and the valve body. With heavy debris in the pan, the whole CVT
2013 to 2016 Nissan Altima and 2014 to 2016 Rogue, P0776Pressure could drop and let the belt slip, with poor acceleration: Nissan fixed it with a reflash (campaign PC490)
2007 to 2009 Toyota Tundra and Sequoia and Land Cruiser (AB60)A computer reflash and, in some cases, a transmission replacement
2015 and 2016 Volkswagen Jetta, Golf and Passat (09G)A broken wire in the solenoid connector, under the starter

All of these are US documents; we found no bulletins or recalls that name Mexico. And no NHTSA bulletin summary from 2000 to 2024 mentions P0778, P0962 or P0963: they're electrical and get fixed by diagnosing the circuit. For Chevrolet, more detail in our 6T40 and Captiva guides; for Nissan, in our Nissan CVT guide.

Step-by-step diagnosis

  • Read every code with a scan tool that reaches the transmission computer, save the freeze frame data and handle the other codes first: GM, Toyota, Jeep and Nissan all say so.
  • Check the fluid level and condition. Honda says to drain it through a strainer: if it carries metal or a lot of clutch material, replace the transmission. Lexus warns that an incorrect level also sets these codes.
  • On Chevrolet, clean the solenoids with the scan tool function that cycles them to dislodge debris, and retest.
  • Measure line pressure with a gauge. If it's out of range, fix that first: according to the rebuilding industry, a P0776 with low line pressure can be a "ghost" code.
  • On a CVT, compare the secondary pressure on the gauge with the scan tool reading. Chrysler does it this way on the Compass: if they match, the fault is in the solenoid or its hydraulic circuit; if not, in the pressure sensor or the computer terminals.
  • Test the solenoid: its resistance against the maker's value (table below) and, on Toyota, that the valve clicks when powered through a 21 W bulb in series.
  • If the solenoid is fine, inspect the valve body (stuck, scored or dirty valves) and then the clutches, piston and pump.
  • Leave the computer for last, and after the repair run the relearn the maker requires.

What your findings mean

Electrical code (P0778, P0798, P0962, P0963, P0966 or P0967) and the solenoid out of rangeThe solenoid or its harness. Toyota and Honda replace the solenoid; on 6-speed Chevrolets it's inside the module; on Nissan, the 2016 Pathfinder manual replaces the valve body
Electrical code and the solenoid in rangeWire, connector or the computer; with a good harness, Toyota replaces the computer
P0776 or P0796 with low line pressurePressure first: pump, regulator valve, filter or the line pressure solenoid
P0776 on a Chevrolet 6T40 with good pressureThe 3-5-reverse piston and wave plate, the solenoid filter plate and the 3-5-reverse regulator valve, before the module
P0796 on a Silverado or Tahoe with debris in the panThe 4-5-6 clutch, its hub or the pump; with a clean pan, the valve body
P0776 or P0965 on a Nissan CVTThe belt: if it's fine, the valve body; if it slipped, belt, pulleys, pump and valve body; with heavy debris, the CVT
Stored P0965 on a 2013 Chevrolet 6T70 or 6T75 on cold daysGM says it can be false near 0 °C and that no parts should be replaced

More on testing solenoids in our solenoid guide, and on the valve body and the computer in our valve body and transmission control module guides.

Makers' test values

Nissan JF011E (2007 to 2012 Sentra, 2008 to 2014 X-Trail): secondary pressure3.0 to 9.0 Ω; 5.0 to 7.0 V with the pedal released and 3.0 to 4.0 V at full throttle
2013 Nissan Juke (RE0F10B): secondary pressure5.60 to 6.60 Ω at 20 °C
Nissan JF015E (2013 to 2019 Sentra, Note): primary and line pressureAbout 5.3 Ω at 20 °C, 6.0 at 50 °C and 6.7 at 80 °C
Nissan JF016E and JF017E (2015 to 2022 X-Trail, 2020-on Sentra, Altima, Pathfinder): secondary, primary and line pressure5.5 to 7.0 Ω at 20 °C, 6.0 to 8.0 at 50 °C and 6.5 to 8.5 at 80 °C
Toyota U241E (RAV4): SL25.0 to 5.6 Ω at 20 °C
5-speed Honda: linear solenoid B3 to 10 Ω
Chevrolet 6T40 and 6L80GM publishes no resistance values: the solenoids sit inside the module and are tested with a scan tool and a special tool. According to the rebuilding industry, the 6T40 pressure solenoids measure 3 to 5 Ω, and they should never get 12 V directly

Resistance changes with temperature: measure with the transmission cold and compare with the maker's value for your unit. There's no universal value.

Can I drive with P0776 or P0796?

Only to get to the shop. The computer raises pressure to maximum and limits the gears: on Chevrolet's 6T40, reverse and 2nd or 3rd, and the second-generation 6T40 can drop to neutral while moving; on a Nissan CVT, the car starts and accelerates slowly and the speed won't climb. The longer you drive that way, the more likely the damage spreads from the solenoid or valve body to the clutches or, on a CVT, to the belt and pulleys.

P0776 and P0796 myths

  • "P0776 is always the solenoid." GM and Nissan bulletins almost never replace just the solenoid: they replace pistons, wave plates, housings, hubs, valve bodies and CVT belts.
  • "Every transmission has three pressure solenoids, A, B and C." Toyota goes up to D and GM up to E; Hyundai and Kia use one code per solenoid, and Nissan CVTs have two "B"s.
  • "A fluid change will clear it." Only if the level was low, as in a US GM bulletin for the 2025 Equinox; with debris in the pan, Nissan replaces the CVT.
  • "P0965 is a wiring problem." On Chevrolet it's a current comparison that doesn't turn on the check engine light, and GM calls it false near 0 °C on 2013 6T70s and 6T75s; on Nissan, it's primary pulley pressure or ratio.
  • "Stuck off means low pressure." Not always: on the Compass, Chrysler describes P0776 as high pressure, and solenoids that give maximum pressure with no current go to maximum when they're switched off.
  • "Nissan sells the CVT solenoid separately." Nissan replaces the valve body or the transmission.
  • "There's one ohm value for all of them." Each transmission has its own, and GM publishes none for its 6-speeds.

After the repair

Clear the codes and run the relearn the maker requires: on Chevrolet, the adaptive values learn (on the 6L80, the "Service Fast Learn"); on Nissan, the additional service procedure, checking that the computer has the right part number. Then drive until you repeat the code's conditions: on JF016E CVTs, Nissan says to drive in D at 40 km/h or more for about 20 seconds; on the 6L80, GM says to reach 5th at more than 15 % throttle, twice. If the code comes back, check the hydraulic side. Look up any other code in our diagnosis by code, and the shift solenoid codes in our P0750 and P0755 guide.

See TSS solenoids

TSS parts for these codes

The solenoids page has every TSS solenoid. These are the parts that match the documented causes in this guide:

Nissan doesn't sell its CVT solenoids separately, and TSS doesn't carry the 6T40's 3-5-reverse piston or wave plate, or the 6L80's 4-5-6 hub. On Honda, confirm which linear solenoid is position B or C on your transmission, and on the 6T40, whether your module is 1st or 2nd generation. Confirm each part with your distributor using the model, year and transmission code. The difference between the Rojo and Dorado overhaul kits, for when the clutches need work, is in our TSS overhaul kits guide.

TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • What does code P0776 mean?

    That pressure control solenoid "B" didn't achieve what the computer commanded (performance or "stuck off"). Which solenoid "B" is depends on the make: on 6-speed Chevrolets, the 3-5-reverse clutch solenoid; on Nissan, Jeep and Mitsubishi CVTs, the secondary pressure solenoid; on Toyota, SL2.

  • Is P0776 always the solenoid?

    No. GM lists the 3-5-reverse regulator valve, the solenoid filter plate, the pump and the clutch retaining ring, and its bulletins replaced wave plates and pistons; Toyota names the valve body and the clutches. Check the fluid and line pressure first.

  • What is P0965 on a Sentra, Kicks, Versa or X-Trail?

    The CVT's primary pressure solenoid: primary pulley pressure or ratio doesn't follow what the computer commanded. Nissan's manual ends in replacing the transmission; its US bulletins inspect the belt and, if it's fine, replace only the valve body. On a Chevrolet 6T40, P0965 is something else: an electrical fault that doesn't turn on the check engine light.

  • My Cruze or Trax has P0776 and no reverse. What is it?

    In the US, GM documented the 3-5-reverse clutch wave plate and piston and, on early-2011 units, a solenoid inside the module. It says to inspect the piston before replacing the module. With P0776, the 6T40 holds reverse and 2nd, or on second-generation units drops to neutral while moving.

  • What does P0796 mean on a Cheyenne, Silverado or Tahoe?

    That solenoid C, the 4-5-6 clutch solenoid, is "stuck off": the transmission may slip or miss 4th, 5th and 6th, which use that clutch. In the US, GM tied it to 4-5-6 clutch and pump damage, a broken 4-5-6 hub and, on 8-speeds, the valve body.

  • Are P0778, P0962 and P0963 electrical? What should the solenoid measure?

    Yes: wire, connector, coil or computer. The value depends on the transmission: Nissan JF016E, 5.5 to 7.0 Ω at 20 °C; Toyota SL2, 5.0 to 5.6 Ω; Honda, 3 to 10 Ω. GM publishes no ohm values for the 6T40.

  • Can I keep driving with P0776 or P0796?

    Only to get to the shop: the computer raises pressure and limits the gears (on the 6T40, reverse and 2nd or 3rd, and the second-generation unit can drop to neutral while moving); on a Nissan CVT, it starts slowly and the speed won't climb. Driving on can spread the damage to the clutches or the belt.

  • Can solenoid B be bought separately?

    It depends on the make: Toyota and Honda replace it on its own; GM builds it into the transmission module; Nissan doesn't sell the CVT one and replaces the valve body or the transmission. TSS carries Toyota and Honda solenoids, the 1st-generation 6T40 solenoid set and remanufactured modules.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.