Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

P0716, P0717, P0721 and P0722: speed sensor codes

TSS editorial team · · · 12 min read

Gloved technician inspecting transmission speed sensor wiring and harness connector in an engine bay for codes P0716 to P0722
In short
  • P0717 and P0722 are "no signal" codes: the computer can't see the input (turbine) or output speed sensor. P0716 and P0721 are performance codes: there's a signal, but it changes in an impossible way.
  • Depending on the make, the same fault can show up under another number: older Chryslers such as the 41TE use P0715 and P0720, and Nissan uses P0720 on its CVTs.
  • With these codes the transmission goes into limp mode: GM's 6T70 leaves only reverse and 5th, and Chrysler holds 2nd or 3rd.
  • Before buying the sensor, check the connector, harness and supply: GM says not to replace parts if the scan tool test passes, and Hyundai says not to replace the transmission for these codes.
  • If there's also no reverse or missing gears, there may be internal damage: GM and Ford documented damaged rings and tone wheels with a good sensor.

P0716, P0717, P0721 and P0722 are codes for the two sensors that tell the computer how fast the transmission is turning: the input (or turbine) sensor, which reads the shaft coming from the converter, and the output sensor, which reads the shaft going to the wheels. With both speeds the computer works out each gear's ratio. Each sensor's symptoms are in our guides to the TSS input sensor and the output speed sensor; this one covers diagnosing the codes.

What do P0716, P0717, P0721 and P0722 mean?

The generic names (Hyundai prints them as-is in its bulletins) and what each make measures:

P0716Input (turbine) speed sensor: range or performance. There's a signal, but it changes in an impossible way: on GM's 6T70, input speed drops 1,350 rpm for more than 1 second and doesn't recover
P0717Input (turbine) speed sensor: no signal. GM's 6T70 sets it below 50 rpm for 5 seconds; the 4-speed Aisin sets it when the output sensor has a signal and the input sensor doesn't
P0721Output speed sensor: range or performance. The signal is there but makes no sense: noise, an intermittent contact or a damaged or displaced tone ring
P0722Output speed sensor: no signal. GM's 6T70 sets it when output reads 70 rpm or less for 4 seconds while driving

Each make gives the sensors its own name, and some use other numbers for the same fault. Sun Transmissions explains P0715 and P0720 (each sensor's circuit fault) in its posts on P0715 and P0720.

GMInput speed sensor (ISS) and output speed sensor (OSS). On the 4L60E, the output sensor is the vehicle speed sensor and uses P0502 and P0503
FordTSS (turbine shaft speed sensor) for input and OSS for output
Chrysler, Dodge, Jeep and RAMInput and output speed sensor. On older transmissions such as the 41TE, the fault shows up as P0715 or P0720
HondaMainshaft speed sensor for input and countershaft speed sensor for output
Hyundai and KiaPulse generator A (PG-A) for input and B (PG-B) for output. On the 6-speed both are a single part
NissanOn its CVTs, an output sensor fault shows up as P0720
VolkswagenOn the 09G, G182 is the input sensor and G195 the output, both behind the valve body; on the 01M, G38 and G68

P0716, P0717, P0721 and P0722 symptoms

  • Check engine light on; Mazdas also turn on the transmission warning light.
  • Limp mode: the transmission holds one gear and shifts hard. GM's 6T70 raises line pressure to maximum and leaves only reverse and 5th; in its limp mode, Chrysler holds 2nd on its 4-speeds and 3rd on the 62TE and the RFEs.
  • It starts in a high gear or won't upshift: Ford's 6R80 can take off in 5th when the output sensor fails.
  • Speedometer at 0 or moving on its own, and cruise control dropping out, when the output sensor fails on cars that take speed from it.
  • A sudden downshift to 1st on the highway: Ford recalled 2011 to 2014 F-150s in the US over output sensor signal losses.
  • No reverse or missing gears, when the cause is internal damage (see the causes).

What causes these codes?

In the bulletins makers published in the US with these codes, the causes split between module software, the sensor itself, the wiring and, less often, internal damage with a good sensor. The service manuals say to check:

  • The connector and harness: backed-out or loose terminals, moisture or corrosion (Nissan documented it on its connectors) and pinched or chafed wires.
  • Power feed and ground, on sensors powered by the module: on 2013 4L60E pickups, GM fixed P0716 and P0717 by repairing the sensor circuit and the module ground.
  • Metal debris stuck to the sensor tip; GM always asks to check it.
  • The tone ring the sensor reads: damaged, misaligned or displaced teeth.
  • The sensor itself, or the part that carries it: on Ford's 6R80 the output sensor sits in the valve body's molded lead frame, and on 6-speed Hyundais and Kias the input and output sensors are a single part.
  • Module software: Honda, Ram and Mazda fixed these codes with reprogramming.

These are the documented cases on models also sold in Mexico. They're US or North American bulletins; we found none that names Mexico:

2016 Traverse, Acadia, Enclave and Equinox V6 (6T70 and 6T75)No reverse or 3rd, with P0716, P0717 and P0776: the retaining ring of the input sensor's tone ring came out of its groove. The sensor was fine
2015 and 2016 Ford Edge and Explorer (6F50 and 6F55)No reverse, 3rd or 5th, with P0715, P0717, P0756 and P2701: the direct clutch tone wheel fails. Ford replaces the TSS along with the clutch parts and cleans metal particles out of the transmission
2011 to 2014 Ford F-150 (6R80; the Lobo in Mexico)Output sensor signal losses that dropped the transmission into 1st: five US recalls, with new software and, on 2014 trucks, a new molded lead frame. We found no campaign in Mexico
6-speed Hyundais and Kias (2011 to 2017 Elantra, 2012-on Accent, Tucson, Santa Fe, Sonata)P0717, P0721 or P0722: the input/output sensor, a single part, is replaced along with the valve body harness. Hyundai says not to replace the transmission for these codes
2013 Silverado and Cheyenne (4L60E)P0716 or P0717: the input sensor circuit and the module ground; if the module pins have no continuity, GM replaces the module and the sensor
2016 to 2019 Honda Pilot and 2018 and 2019 Odyssey (9-speed)P0716: fixed with a transmission module software update
2019 Ram 1500 (8-speed)P0716 or P0721: fixed with reprogramming
Mazdas with the Skyactiv transmission, 2012 to 2014P0722 with no real fault: Mazda fixed the module logic with software

Step-by-step diagnosis

This order comes from GM, Hyundai, Ford and Chrysler manuals and bulletins. You need a scan tool that shows input and output speeds and a multimeter:

  • Step 1. Read all codes and the freeze frame. If there are also gear ratio, pressure or solenoid codes, the diagnosis changes: in the internal damage cases, these codes came with P0776, P0756 or P2701.
  • Step 2. Scan tool test. In P or N, input speed should equal engine rpm; on GM's 6T70, in Park it reads 500 to 5,800 rpm and follows the engine without dropping out. While driving, input and output rise smoothly and never fall to 0.
  • Step 3. If the test passes and the code doesn't come back when driving under the same conditions, stop there: GM warns that more testing leads to replacing parts that weren't needed.
  • Step 4. Connector and harness. Look for backed-out, loose or bent terminals, moisture, corrosion and pinched wires. Hyundai says to check the harness between the computer and the transmission and for pins not fully inserted.
  • Step 5. If the sensor is a Hall-effect type (powered by the module), measure its supply against the manual: 8.3 to 9.3 V on GM's 6T70. If it's magnetic, it makes its own AC signal: measure it in AC volts and Hz, not against a fixed resistance value.
  • Step 6. Sensor tip and tone ring: stuck metal debris, damaged or misaligned teeth, and the sensor bolt at its correct torque (GM).
  • Step 7. Software: look for updates for your VIN. Honda, Ram and Mazda fixed these codes by reprogramming the module.
  • Step 8. The sensor or the part that carries it: on 6-speed Hyundais and Kias the input/output sensor is replaced with the valve body harness; on Ford's 6R80, the molded lead frame.
  • Step 9. If there's also no reverse or missing gears, suspect internal damage: GM and Ford documented a displaced tone ring and a damaged tone wheel with a good sensor.
  • Step 10. When you're done, clear the codes, run the transmission relearn the make calls for and drive under the conditions that set the code.

What your results mean

In P or N, input reads the same as engine rpm and doesn't drop outThe input sensor and its circuit are working at that moment. If the code doesn't come back when driving, GM says not to replace parts
Input stays at 0 while output readsNo input signal (P0717): connector, harness, sensor supply if it's a Hall-effect type, or the sensor
The signal jumps or drops suddenly and comes backPerformance fault (P0716 or P0721): an intermittent connection, debris on the sensor tip or a damaged or misaligned tone ring
Output reads 0 and the speedometer doesn't moveNo output signal (P0722): the output sensor or its circuit. Note: on many newer cars the speedometer uses the wheels, so a working speedometer doesn't prove the sensor is good
Supply out of range (GM 6T70: outside 8.3 to 9.3 V)GM replaces the control solenoid valve assembly, which holds the module
Good readings, but no reverse or missing gearsPossible internal damage: a displaced tone ring or a damaged clutch tone wheel
Hyundai or Kia: output changes smoothly with vehicle speedThe wiring has no opens or shorts at that moment; Hyundai moves on to the harness and pins

Makers' test values

There's no universal value: it depends on whether the sensor is a Hall-effect type, which is powered by the module and tested by its supply, or magnetic, which makes its own signal. The resistance values that circulate online don't apply to Hall-effect sensors. These are the values makers publish in their service manuals, each for the model shown:

GM 6T70 and 6T75 (Traverse, Acadia, Equinox V6), Hall effect8.3 to 9.3 V supply. In Park, input speed reads 500 to 5,800 rpm and follows the engine
GM 6L80 (2012 Tahoe manual), Hall effect8.3 to 9.3 V supply. The input and output sensors share one harness, on the valve body
GM 6T40 and 6T45 (2012 Cruze manual), Hall effect11 to 13 V supply, battery voltage
2012 Ram 2500 and 3500 6.7 diesel (Aisin AS68RC), Hall effect8.0 V supply, plus or minus 0.2 V
2010 Honda Civic, 5-speed automatic, 3-pin sensorWith the sensor unplugged and the key ON, about 5 V at terminal 1 and at terminal 2; terminal 3 goes to ground
2011 Hyundai Elantra, 6-speed automatic, current-type Hall effectSignal high 1.18 to 1.68 V (11.8 to 16.8 mA) and low 0.59 to 0.84 V (5.9 to 8.4 mA)
GM 4T45E (2006 Malibu 2.2), magneticInput sensor: 625 to 725 Ω at 20 °C and 750 to 835 Ω at 100 °C, measured at the 20-way connector
Toyota U341E (2010 Corolla 1.8), magneticTurbine (NT) sensor, between terminals 1 and 2, at 20 °C: 560 to 680 Ω. First check the sensor has no play in the case
2007 Kia Rio, 4-speed automatic, magneticInput sensor (PG-A): 245 Ω, plus or minus 30, at 20 °C
GM magnetic vehicle speed sensorMakes AC: about 25 Hz per mph, about 15.5 Hz per km/h. GM measures it with the multimeter set to AC volts and Hz
4-speed Aisin (Saab 9-5)In P or N, input speed should equal engine rpm; P0717 sets if the output sensor has a signal and the input sensor doesn't

Can I drive with code P0717?

Only slowly and only to the shop. With these codes the transmission goes into limp mode: it holds one gear with line pressure at maximum, and some transmissions take off in a high gear. If the output sensor is the one failing, be careful on the highway: Ford recalled 2011 to 2014 F-150s in the US because losing that signal could drop the transmission into 1st.

P0717 and P0722 myths

  • "Replace the sensor and you're done." GM says to stop if the scan tool test passes and to check the supply, wiring and tone ring first; on the 2016 6T70 the fault was the ring, with a good sensor.
  • "Replace both sensors even if only one fails." Replace the one that fails. The exception is 6-speed Hyundais and Kias, where input and output are a single part.
  • "The sensor always gets 5 V." There's no universal value: GM feeds the 6T70's sensors 8.3 to 9.3 V and the 6T40's 11 to 13 V, the Ram diesel 8 V, and magnetic sensors get no power at all. 5 V is Honda's value on the 2010 Civic.
  • "P0717 means the transmission is finished." Hyundai says not to replace the transmission for these codes. Internal damage is suspected only if there's also no reverse or missing gears.
  • "The sensor is on the outside and easy to change." On many transmissions it's inside: on GM's 6T70, Ford's 6R80, VW's 09G and the Hyundai/Kia 6-speed you have to drop the pan or the valve body.
  • "Change the fluid and the code goes away." No maker document we checked lists fluid as a cause of these codes. What they do document is metal debris stuck to the sensor tip.

After the repair

Clear the codes, run the transmission relearn the make calls for and drive under the same conditions that set the code. If your F-150 came from the US, check its VIN for open recalls. And if the transmission shows other codes, look them up in our diagnosis by code.

See TSS speed sensors

TSS speed sensors

When the diagnosis confirms the sensor, these are the TSS sensors for the most common transmissions in Mexico. The full list by vehicle is in our guides to the TSS input sensor and the output speed sensor:

62TE (2008-on Journey, Grand Caravan and Town & Country)2-pin input and output sensor
41TE and A604 (Caravan, Voyager, Stratus, PT Cruiser)Input and output sensor kit, or separately the input and output sensors
42RLE, 45RFE, 545RFE and 68RFE (Liberty, Wrangler, Ram, Durango)42RLE input and RFE input/output sensor and 42RLE output sensor
6T40 and 6T45 (Sonic, Cruze, Trax, Malibu, Equinox)Input sensor and output sensor
6L80, first generation (Silverado, Cheyenne, Tahoe, Suburban)Input and output sensor
1996-on 4L60E (Silverado, Cheyenne, Tahoe, S10)Output (vehicle) speed sensor
6F50 and 6F55 (Edge, Explorer)Input sensor and output sensor
DPS6 PowerShift (Focus, Fiesta, EcoSport)Kit of 3 input and output sensors
09G (Jetta, Golf, Beetle, Tiguan)Speed sensor with blue connector
01M (Jetta A4, Golf A4, Beetle)3-pin sensor with harness and input sensor with D-shaped connector
Nissan JF011E and JF010E CVTs (Sentra, X-Trail, Altima)Output speed sensor
Toyota AvanzaInput and output sensor

Confirm your transmission in the Transmisiones Veinte 07 transmission finder before ordering: the sensor changes with the year and the connector.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • What does code P0717 mean?

    That the computer sees no signal from the input (turbine) speed sensor even though the car is moving. GM's 6T70 sets it if input stays below 50 rpm for 5 seconds.

  • What's the difference between P0716 and P0717?

    P0716 is a performance code: there's a signal, but it changes in an impossible way (on GM's 6T70, it drops 1,350 rpm in more than a second). P0717 is no signal. The same goes for P0721 and P0722 on the output sensor.

  • What does code P0722 mean?

    That there's no signal from the output speed sensor. GM's 6T70 sets it if output reads 70 rpm or less for 4 seconds while driving, and on cars that take speed from that sensor the speedometer stays at 0.

  • Can I drive with these codes?

    Only slowly and only to the shop: the transmission goes into limp mode (GM's 6T70 leaves only reverse and 5th; Chrysler holds 2nd or 3rd). With an output sensor fault, some F-150s could drop suddenly into 1st.

  • Does the transmission need replacing?

    Usually not: Hyundai says not to replace it for these codes and GM says not to replace parts if the scan tool test passes. Suspect internal damage if there's also no reverse or missing gears.

  • How do I test the speed sensor?

    With a scan tool: in P or N input speed should equal engine rpm, and while driving output speed rises with vehicle speed without dropping to 0. If the sensor is powered, measure its supply (8.3 to 9.3 V on GM's 6T70, 11 to 13 V on the 6T40); if it's magnetic, its resistance (560 to 680 Ω on the 2010 Corolla's turbine sensor, according to Toyota) or its AC signal.

  • I replaced the sensor and the code came back. What next?

    Check the connector and harness, the module's supply and ground, the tone ring the sensor reads and whether there's new software for your VIN. The module comes last.

  • My scan tool shows P0715 or P0720. Is it the same?

    It's the same sensor under another number: P0715 is the input sensor circuit and P0720 the output sensor circuit. Older Chryslers such as the 41TE and Nissan CVTs use those numbers.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.