Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
System: Incorrect gear ratio (slipping)

Code P0730: Incorrect gear ratio

The computer compares input and output speed and they don't match the gear it commanded: the transmission slips in that gear. It's almost always a worn clutch or band, low pressure, a solenoid or the valve body.

What's failing

Incorrect gear ratio (slipping)

Most common cause

Low or degraded fluid.

Can I drive with this code?

Only as far as the shop

Diagnosis for your car

What car do you have?

Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.

Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →

Symptoms

  • SlippingThe engine revs and the car doesn't pull the same, in one or several gears.
  • On Nissan CVTsJudder, lack of power or the engine revs without road speed building (Nissan calls it belt damage).
  • Limp mode, mistimed shifts or the transmission warning light flashing
  • On the 5R110W in Super Duty trucksDelayed engagement and then no drive, with P0730, P0751 or P2700.

Most common causes

  1. 1Low or degraded fluid
  2. 2The speed sensors or their signalIn 2008, Chrysler reprogrammed CVT-equipped Caliber, Compass and Patriot models that set P0730 when the fault was the input sensor (US).
  3. 3A slipping clutch, band or, on CVTs, push beltHonda 4-speeds use only P0730 for this, and on Nissan CVTs it's the belt code.
  4. 4Low pressure or internal leaksOn the 5R110W, Ford found the coast clutch cylinder weld leaking (2009–2016).
  5. 5SoftwareChrysler reprogrammed the transmission computer on several 2012 models (US), and Kia and Hyundai updated their IVTs with P0730.
  6. 6A false codeGM explains it can set on the 2019–2020 Malibu during vehicle transport; different tire sizes also throw off the ratio.

From most common and easiest to check to least common.

Step-by-step diagnosis

Follow these steps

Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.

Step 1

Are there also codes for a specific gear (P0731 to P0735), or speed sensor, pressure or solenoid codes?

P0730 doesn't say which gear: the other codes point the way, and speed sensor codes are fixed first.

It's guidance: a technician with a scan tool makes the final diagnosis.

See every step and resultShow
  1. Step 1. Are there also codes for a specific gear (P0731 to P0735), or speed sensor, pressure or solenoid codes?Yes: «Fix those codes first» · No: step 2
  2. Step 2. Does the car have no symptoms, and was it recently transported or towed?Yes: «It may be a false code» · No: step 3
  3. Step 3. Is the fluid at the right level and in good condition, with no burnt smell?Yes: step 5 · No: step 4
  4. Step 4. Does the fluid have metal debris or a lot of clutch material?Yes: «Internal wear» · No: «Correct the fluid»
  5. Step 5. On the scan tool, are the input and output speed sensor signals good, and are all the tires the same size?Yes: step 6 · No: «Speed sensors or tires»
  6. Step 6. Is there a software update for your VIN?Yes: «Update the software» · No: step 7
  7. Step 7. At the shop, is the line pressure OK?Yes: «Clutch, band or CVT belt» · No: «Low pressure or internal leaks»

Results

  • Fix those codes first. Fix any speed sensor, pressure or solenoid codes first. If there's a code for a specific gear (P0731 to P0735), follow it: that one says which gear is slipping. They all have their own page in this tool.
  • It may be a false code. If the car has no symptoms, ask about the transport or tow, clear the code and road-test before opening the transmission.
  • Correct the fluid. Set the right level with the fluid the carmaker specifies and find the leak. Then clear the code and road-test.
  • Internal wear. Metal or clutch material in the fluid means internal wear: the transmission needs repair, and an additive or a fluid change won't fix it.
  • Speed sensors or tires. Check the input and output sensors, their connectors and the harness, and fit four tires of the same size: a bad reading or different tire sizes throw off the ratio. Then clear the code and road-test.
  • Update the software. Ask for the reflash for your VIN. On their IVTs, Kia and Hyundai updated the software first and replaced the unit only if needed. Then clear the code and road-test.
  • Low pressure or internal leaks. Check the pump, the valve body and internal leaks. On the 5R110W (2009–2016 trucks), Ford found the coast clutch cylinder weld leaking: it tests it with air at 40 psi through the solenoid body, and if you hear a hiss, the weld is leaking.
  • Clutch, band or CVT belt. If the pressure is good and it slips, it's a clutch or a band: Honda 4-speeds use only P0730 for this. On Nissan CVTs it's the belt code (Nissan calls it belt damage), and driving on can end in replacing the whole unit.
Diagnostic tip

P0730 doesn't say which gear: check for gear-specific codes (P0731–P0735), fix any speed sensor codes first and check fluid level and condition. If the car has no symptoms and was recently transported or towed, ask about that before opening the transmission.

Can I drive with this code?

Only as far as the shop: if it slips, more driving damages the clutch or belt further, and on CVTs it can end in replacing the whole unit.

What carmaker bulletins say33 carmaker bulletins and the vehicles they nameShow

33 service bulletins published by the US NHTSA mention this code, mostly from Chevrolet, Jeep, Dodge, Hyundai, Chrysler (2000–2026 models).

Vehicles with service bulletins for this code

  • Jeep Grand Cherokee 2012
  • Jeep Wrangler 2012
  • Dodge Durango 2012
  • Dodge Charger 2012
  • Chevrolet Monte Carlo 2000–2004
  • Chevrolet Impala 2000–2004
  • Chrysler 300c 2012
  • Ford F-450 Sd 2003–2016
Bulletin TST 140875 Rev · 2024
Can-Am Spyder F3 2015–2024 · Can-Am Spyder Rt 2008–2024

Active P0730 can set if the unit has the wrong rear sprocket or a different wheel size: the cluster stops showing the gear, limp mode with check engine, and no shifting.

Open the bulletin (PDF) ↗
Bulletin TST 140875 · 2023
Can-Am Spyder Rt 2015–2022 · Can-Am Spyder F3 2015–2022

Active P0730 can set if the unit has the wrong rear sprocket or a different wheel size: the cluster stops showing the gear, limp mode with check engine, and no shifting.

Open the bulletin (PDF) ↗
Bulletin 19NA201 · 2019
Chevrolet Malibu 2019–2020

Informational: DTC P0730 may set during vehicle transport and is considered false unless the customer reports the MIL on and other codes may be present.

Open the bulletin (PDF), page 1 ↗
Bulletin 21-033-14 · 2014
Dodge Durango 2012 · Dodge Challenger 2012 · Jeep Wrangler 2012 · Dodge Charger 2012

TCM reprogramming because P0730 (incorrect gear ratio) sets erroneously; also adds shift improvements per engine, such as hanging in gear in hot weather when loaded and delayed shifts.

Open the bulletin (PDF), page 3 ↗

These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.

TSS parts for the transmissions in these bulletins

Buy in

Different transmission? Pick it and we'll show its parts:

See parts →

Find the part by its number on the exploded diagram: 4T65E

Related codes

← See all codes

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.