Code P0962: Pressure control solenoid A control circuit low
A fault in a pressure control solenoid (A, B or C) or its circuit: open, shorted, stuck or out of range. It causes harsh or soft shifts and often puts the transmission in limp mode.
Pressure control solenoid
A short to ground or damaged wire in the pressure control solenoid circuit
Slowly and only to the shop
What car do you have?
Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.
Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →
Symptoms
- Stuck in one gearFord's 6R80 (F-150) in 5th; the 6F35 (Escape, Fusion) only allows P, R, N and 5th and pulls away in 5th; GM's 6L80 in 3rd or 5th.
- On the Aveo, no 4th gear and limp mode, with the check engine light from the first key cycle
- Slipping or lack of powerOn some Fords, a short to ground drops pressure to minimum and the computer limits engine torque (Explorer 5R55W, 4R75E).
- Harsh shifts on other unitsFord describes maximum pressure and harsh engagements on the Focus 4F27E.
Most common causes
- 1A short to ground or damaged wire in the pressure control solenoid circuit"low" usually means that, but it depends on each unit's design.
- 2The transmission or solenoid connectorDirty, loose or wet.
- 3The solenoid windingOn Honda 5-speeds, Honda specifies 3 to 10 ohms.
- 4On Honda, Honda states it's an electrical problem and cannot be caused by a mechanical fault in the transmission
- 5The computer, lastHonda ends with a software update or a known-good computer.
From most common and easiest to check to least common.
Follow these steps
Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.
Are the transmission and solenoid connectors clean, tight and dry?
It's an electrical code: Honda states it comes from an electrical problem and can't be caused by a mechanical fault in the transmission.
It's guidance: a technician with a scan tool makes the final diagnosis.
See every step and resultShow
- Step 1. Are the transmission and solenoid connectors clean, tight and dry?Yes: step 2 · No: «Repair the connector»
- Step 2. Measured with a multimeter, is the solenoid wire OK, with no short to ground or damage?Yes: step 3 · No: «Short to ground or damaged wire»
- Step 3. Does the solenoid coil measure within that transmission's value?Yes: «The computer, last» · No: «Replace the solenoid»
Results
- Repair the connector. Clean, dry and secure the transmission or solenoid connector, clear the code and test again.
- Short to ground or damaged wire. Repair the damaged wire or the short to ground before replacing the solenoid. Then clear the code and test again.
- Replace the solenoid. If the coil measures out of range, replace that transmission's pressure solenoid: the line pressure solenoid, or linear A on Honda 5-speeds.
- The computer, last. With the connector, wire and coil OK, check the computer: Honda ends with a software update or a known-good computer.
Which solenoid it is depends on the unit: on Nissan, Ford and GM it's the line pressure solenoid; on Honda 5-speeds it's linear clutch solenoid A. Measure the solenoid resistance and check the wiring for a short to ground before replacing parts.
Slowly and only to the shop: if it's stuck in 5th it pulls away weakly, and if it slips with engine torque limited it can be damaged further.
TSS parts for this code
Pick your transmission to see the TSS parts that fit it, or open all parts of this type:
Buying wholesale or own a parts store?
We'll send you a quote or tell you how to sell TSS in your area.