Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
System: Pressure control solenoid

Code P0963: Pressure control solenoid A control circuit high

A fault in a pressure control solenoid (A, B or C) or its circuit: open, shorted, stuck or out of range. It causes harsh or soft shifts and often puts the transmission in limp mode.

What's failing

Pressure control solenoid

Most common cause

An open circuit or short to voltage

Can I drive with this code?

It can be driven carefully to the shop

Diagnosis for your car

What car do you have?

Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.

Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →

Symptoms

  • Harsh shifts and engagementsFord describes maximum line pressure on the 6R80, 6F35 and 4F27E.
  • On the Aveo, no 4th gear and limp mode, with the check engine light on
  • On Nissan CVTs, if the line pressure solenoid failsA bump when shifting into gear, slow take-off and acceleration, and no converter lockup.
  • On the Explorer with the 5R55W, Ford ties it to an intermittent short to ground or to voltage

Most common causes

  1. 1An open circuit or short to voltageNissan describes it this way.
  2. 2The solenoid or transmission connector, dirty, loose or wet
  3. 3The pressure control solenoid windingMeasure it against that unit's spec.
  4. 4On the Jeep and Dodge CVT, Chrysler sets it when the actual line pressure solenoid current stays far below what the computer commands for 5 seconds
  5. 5On the Cruze, Sonic and Trax with the 6T40, the solenoid is inside the module; GM asks about this code before accepting a module return

From most common and easiest to check to least common.

Step-by-step diagnosis

Follow these steps

Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.

Step 1

Are the transmission and solenoid connectors clean, tight and dry?

It's guidance: a technician with a scan tool makes the final diagnosis.

See every step and resultShow
  1. Step 1. Are the transmission and solenoid connectors clean, tight and dry?Yes: step 2 · No: «Repair the connector»
  2. Step 2. Measured with a multimeter, is the solenoid circuit OK, with no opens or shorts to voltage?Yes: step 3 · No: «Open circuit or short to voltage»
  3. Step 3. Does the solenoid coil measure within that transmission's value?Yes: «The computer, last» · No: «The solenoid, or the part that carries it»

Results

  • Repair the connector. Clean, dry and secure the transmission or solenoid connector, clear the code and test again.
  • Open circuit or short to voltage. Repair the open wire or the short to voltage before replacing the solenoid. Then clear the code and test again.
  • The solenoid, or the part that carries it. If the coil measures out of range, replace the solenoid or the part that carries it: on the 6T40 it's inside the module, and on Nissan CVTs the solenoid isn't sold separately.
  • The computer, last. With the connector, circuit and coil OK, check the computer, always last. On the 6T40, GM asks about this code before accepting a module return.
Diagnostic tip

On most units the solenoid gives maximum pressure with no current: that's why an open circuit feels like banging, not slipping. Check the connector and wiring first, and on CVTs remember Nissan doesn't sell the solenoid separately.

Can I drive with this code?

It can be driven carefully to the shop: with maximum pressure the transmission bangs but usually moves; on a CVT, avoid hard acceleration until it's fixed.

TSS parts for this code

Pick your transmission to see the TSS parts that fit it, or open all parts of this type:

See parts →

Related codes

← See all codes

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.