Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
System: Fluid pressure sensor or switch

Code P0841: Transmission fluid pressure sensor/switch A range/performance

A fault in a transmission fluid pressure sensor or switch (A, B or C) or its circuit. On many transmissions these switches sit in the valve body or the solenoid pack.

What's failing

Fluid pressure sensor or switch

Most common cause

Moisture or corrosion at the solenoid pack connector

Can I drive with this code?

Only as far as the shop

Diagnosis for your car

What car do you have?

Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.

Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →

Symptoms

  • Limp modeOn Chryslers the transmission stays in one gear (2nd on 4-speeds, 3rd on the 62TE), and on Renault and Peugeot DP0 and AL4 units, in 3rd.
  • Slow to engage D or R, or no drive (Chrysler's 545RFE monitors it along with other pressure codes)
  • On CVTsJudder, lack of power or, on Subaru, the transmission temperature light on.
  • Check engine light on, sometimes along with other pressure switch codes (P0846, P0871)

Most common causes

  1. 1Moisture or corrosion at the solenoid pack connectorChrysler documented this on the 42RLE in the 2003–2005 Liberty, Wrangler, Dakota and Durango (US).
  2. 2The part that reads pressure, by makeOn Chrysler (41TE, 42RLE, 62TE, RFE), the L/R pressure switch inside the solenoid pack; on Renault and Peugeot DP0 and AL4, the pressure sensor and its wiring.
  3. 3Actual low pressureA misinstalled filter (on the 545RFE, Chrysler checks that the filter seal goes into the pump bore), the pump or a sticking regulator valve.
  4. 4The valve bodySolenoid switch valve wear on Chrysler, per the rebuilding industry; on 2023–2024 GM units, an incorrectly machined passage; on Subaru, contamination in a pressure solenoid valve or air bubbles in the fluid.
  5. 5On Nissan CVTs, the primary and secondary pressure sensors disagreeNissan removes the valve body and inspects the belt before deciding what to replace.
  6. 6SoftwareSubaru released reprogramming for this code, and on the 2018–2020 ProMaster 3.6 (US) it was fixed by reprogramming the ABS module.

From most common and easiest to check to least common.

Step-by-step diagnosis

Follow these steps

Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.

Step 1

Is the fluid at the right level, and is the filter correctly installed?

Real low pressure also sets this code. On the 545RFE, Chrysler checks that the filter seal goes into the pump bore.

It's guidance: a technician with a scan tool makes the final diagnosis.

See every step and resultShow
  1. Step 1. Is the fluid at the right level, and is the filter correctly installed?Yes: step 2 · No: «Fix the fluid and filter»
  2. Step 2. Are the connector and wiring of the sensor or solenoid pack dry and clean, with no moisture, corrosion or damaged insulation?Yes: step 3 · No: «Repair the connector or wiring»
  3. Step 3. Is there a reflash for your model?Yes: «Update the software» · No: step 4
  4. Step 4. Is your transmission a CVT?Yes: «Inspect the CVT inside» · No: step 5
  5. Step 5. Measured with a gauge, is the actual line pressure OK?Yes: «The switch or sensor» · No: «Low pressure: hydraulics»

Results

  • Fix the fluid and filter. Correct the level with the fluid the carmaker specifies and, if the filter was misinstalled, install it correctly; then clear the code and test again.
  • Repair the connector or wiring. Dry, clean or repair the connector and wiring before replacing the solenoid pack or the sensor, then clear the code and test again.
  • Update the software. Ask the dealer for the reflash for your VIN, then clear the code and road-test.
  • Inspect the CVT inside. On CVTs, P0841 sets when the primary and secondary pressure sensors disagree: Nissan removes the valve body and inspects the belt before deciding what to replace. On Subaru, contamination in a pressure valve or air bubbles in the fluid also cause it.
  • The switch or sensor. With actual pressure good, the fault is electrical or the switch. On Chrysler (41TE, 42RLE, 62TE, RFE) it's the on/off L/R switch inside the solenoid pack, which is replaced with the assembly; on Renault and Peugeot DP0 and AL4 units, the pressure sensor.
  • Low pressure: hydraulics. If actual pressure is low, the problem is hydraulic: the filter, the pump or a sticking regulator valve. On Chrysler, the rebuilding industry also ties it to wear of the valve body's solenoid switch valve.
Diagnostic tip

Know what P0841 is on your make: on Chrysler it's an on/off pressure switch inside the solenoid pack, not a 5 V sensor. Before replacing the solenoid pack, check the connector for moisture and measure line pressure with a gauge: if actual pressure is good, the fault is electrical or the switch; if it's low, it's hydraulic.

Can I drive with this code?

Only as far as the shop: many units go into limp mode, and if actual pressure is low the clutches or belt slip and get damaged further.

What carmaker bulletins say54 carmaker bulletins and the vehicles they nameShow

54 service bulletins published by the US NHTSA mention this code, mostly from Nissan, Subaru, RAM, Chevrolet, GMC (2001–2024 models). The repair they mention most: updating the computer software.

Vehicles with service bulletins for this code

  • Nissan Altima 2013–2020
  • Nissan Rogue 2014–2020
  • Subaru Legacy 2010–2019
  • Subaru Outback 2010–2019
  • RAM 2500 2024
  • RAM 3500 2024
  • Chevrolet Impala 2006–2010
  • Chevrolet Monte Carlo 2006–2007
Bulletin PIP6018 · 2024
GMC Savana 2023–2024 · GMC Canyon 2023–2024 · Cadillac Ct4 2023–2024 · Chevrolet Camaro 2023

Preliminary information: inspect for an incorrectly machined fluid passage in the valve body that causes DTC P0841.

Open the bulletin (PDF), page 1 ↗
Bulletin 16-111-18R · 2019
Subaru Legacy 2018 · Subaru Forester 2018 · Subaru Crosstrek 2018 · Subaru Impreza 2018

TR580 CVT: new TCM reprogramming because contamination in a pressure solenoid valve can cause P0841. The new logic operates the solenoid so it can discharge the contamination.

Open the bulletin (PDF), page 2 ↗
Bulletin 16-119-19 · 2019
Subaru Outback 2010–2016 · Subaru Legacy 2010–2017 · Subaru Impreza 2013–2017 · Subaru Crosstrek 2013–2017

New valve body to prevent false P0841 and/or the AT Temp light: aerated fluid entered some pressure circuits and skewed the pressure calculation. The circuit shape was changed.

Open the bulletin (PDF), page 2 ↗

These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.

TSS parts for this code

Pick your transmission to see the TSS parts that fit it, or open all parts of this type:

See parts →

Related codes

← See all codes

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.