6T70, 6T75, 6L50, 6L80 and 6L90: how to check the TFP switch for false DTCs P0842, P0843, P0872, P0873, P0877, P0878, P0989 or P0990.
Code P0872: Transmission fluid pressure sensor/switch C circuit low
A fault in a transmission fluid pressure sensor or switch (A, B or C) or its circuit. On many transmissions these switches sit in the valve body or the solenoid pack.
Fluid pressure sensor or switch
On Mazda SKYACTIV (2012–2021), oil pressure switch No. 3 stuck from contamination in its passage; Mazda reprograms the module or replaces the switch.
If it drives normally, it can be taken to the shop
What car do you have?
Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.
Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →
Symptoms
- Check engine light on and, on Mazda SKYACTIV models, the AT light, sometimes with P0780 or P1738
- On the first-generation 6T40 (Cruze, Sonic), it can set with P0752, P0877 or P0989, sometimes with limp mode, per the rebuilding industry
- On 2001–2004 Silverado and Sierra HD with the Allison (US), GM listed it with harsh or delayed 2-1 downshifts, a neutral feel at a stop, shift busyness, or slow engagement and a blank gear display
Most common causes
- 1On Mazda SKYACTIV (2012–2021), oil pressure switch No. 3 stuck from contamination in its passage; Mazda reprograms the module or replaces the switch
- 2On the first-generation 6T40, the pressure switches in the control moduleThe industry repairs them with a seal kit without replacing the whole module.
- 3A false readingGM has a TFP switch check to rule out false codes on the 6T70, 6T75, 6L50, 6L80 and 6L90.
- 4Pressure sensor/switch C, its connector or its circuit shorted to ground
- 5Low or dirty fluid
From most common and easiest to check to least common.
Follow these steps
Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.
Is the fluid at the right level and clean?
Low or dirty fluid also sets this code.
It's guidance: a technician with a scan tool makes the final diagnosis.
See every step and resultShow
- Step 1. Is the fluid at the right level and clean?Yes: step 2 · No: «Correct the fluid»
- Step 2. Is your car a Mazda with a SKYACTIV-Drive transmission?Yes: step 3 · No: step 4
- Step 3. Is there a transmission module reflash for your model and year?Yes: «Reflash the module» · No: «Replace both switches»
- Step 4. Is your car a GM 6-speed, such as the 6T40 (Cruze, Sonic, Trax) or the 6L80?Yes: «Switches inside the module» · No: step 5
- Step 5. Is your car a Honda V6 5-speed?Yes: «4th clutch switch: an electrical fault» · No: step 6
- Step 6. Are the switch or sensor connector and circuit OK, with no shorts to ground?Yes: «Replace the switch or sensor» · No: «Repair the circuit»
Results
- Correct the fluid. Correct the level with the fluid the carmaker specifies; if it's dirty, change it along with the filter. Then clear the code and test again.
- Reflash the module. Ask the dealer to reflash the transmission module and then run the initial learning. If the code returns, Mazda replaces both switches, A and B. In Mexico, the bulletin says the repair is covered by the new-car warranty.
- Replace both switches. Mazda replaces both pressure switches, A and B, and then runs the initial learning. Reaching them means removing the pan, and switch B sits under the strainer.
- Switches inside the module. GM doesn't sell them separately and explains that normal debris in the fluid can set them intermittently. Run GM's check to rule out a false code and confirm whether your 6T40 is first or second generation before ordering parts: on the first, the rebuilding industry repairs the switches with a seal kit without replacing the module.
- 4th clutch switch: an electrical fault. On Honda V6 5-speeds, P0872 is the 4th clutch pressure switch. Honda treats these codes as an electrical fault: the switch, its wire or the computer's software, never the transmission. On the 2008 Accord V6 it doesn't turn on the check engine light.
- Replace the switch or sensor. With the connector and circuit OK, replace pressure switch/sensor C. First confirm on your scan tool which part it is: on Toyota's U660E, P0872 is pressure switch No. 1.
- Repair the circuit. Repair the wire shorted to ground or the connector before replacing the switch, then clear the code and test again.
On the Cruze, Sonic and Trax with the 6T40, the pressure switches are inside the transmission module and GM doesn't sell them separately: confirm whether it's a first- or second-generation unit before ordering parts, and run GM's check to rule out a false code.
If it drives normally, it can be taken to the shop; if it's in limp mode, drive slowly and only as needed.
What carmaker bulletins say34 carmaker bulletins and the vehicles they nameShow
34 service bulletins published by the US NHTSA mention this code, mostly from Mazda, GMC, Chevrolet, Pontiac, Cadillac (2001–2021 models).
Vehicles with service bulletins for this code
- Mazda Mazda3 2012–2018
- Mazda Mazda6 2014–2021
- GMC Sierra 2001–2005
- Chevrolet Silverado 2001–2005
- Chevrolet Silverado 3500 2001–2007
- Cadillac Xlr 2006–2007
- Cadillac SRX 2007
- Buick Enclave 2008
Slow or no engagement, no start, blank or flashing PRNDL display, with DTCs P0708, P0872, P0847, P0875, P1711, P1713 or U1000.
These are US bulletins: check with your dealer or shop whether they apply to your car.
TSS parts for the transmissions in these bulletins
Sensor Entrada / Salida para Flecha tipo Viejo 2006/13 6L50 6L80 6L90 6L45 GA6-L45R
Switch Neutro (Conector 6 Cables Verdes) 6L50 6L80 6L90 MYB MYC MYD LY6
Cuerpo de Válvulas Reconstruido 6L80 2010-UP Casting 0955
Cuerpo de Válvulas Reconstruido 6L90 2010-UP Casting 0955
Different transmission? Pick it and we'll show its parts:
Find the part by its number on the exploded diagram: 6T70 · 6L80
Buying wholesale or own a parts store?
We'll send you a quote or tell you how to sell TSS in your area.