Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
System: Fluid pressure sensor or switch

Code P0870: Transmission fluid pressure sensor/switch C circuit

A fault in a transmission fluid pressure sensor or switch (A, B or C) or its circuit. On many transmissions these switches sit in the valve body or the solenoid pack.

What's failing

Fluid pressure sensor or switch

Most common cause

Loss of pump pressure

Can I drive with this code?

If the transmission is in limp mode, drive slowly and only to the shop

Diagnosis for your car

What car do you have?

Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.

Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →

Symptoms

  • Limp mode with the check engine lightOn the 62TE, if the overdrive (OD) pressure switch fails to respond in two consecutive tests, Chrysler puts the transmission in limp mode.
  • It can set at the same time as P0944, P0732, P0734 or P0846, and that changes the diagnosis
  • On 2001–2003 Silverado and Sierra HD with the Allison (US), GM listed it with slipping, delayed engagement and cold hesitation
  • On the 2018 Ram 2500 and 3500 with the 68RFE (US), it can set alone with no real fault

Most common causes

  1. 1Loss of pump pressureIf P0944 is also present, Chrysler diagnoses that first (level, filter, pump).
  2. 2WiringThe OD switch signal open, shorted to ground or to voltage, or the transmission relay output open.
  3. 3The valve bodyIf the computer and wiring pass the simulator test, Chrysler disassembles and inspects the valve body before replacing the solenoid assembly.
  4. 4The solenoid/range sensor assemblyOn the 62TE, if P0870 sets with P0732, P0734 or P0846, Chrysler replaces it directly.
  5. 5SoftwareOn the 2018 Ram 2500 and 3500 with the 68RFE (US) it was a calibration issue, and on the 2017 Ram ProMaster (US) it was fixed by reprogramming the computer.

From most common and easiest to check to least common.

Step-by-step diagnosis

Follow these steps

Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.

Step 1

Is P0944 (pump lost prime) set too?

If so, Chrysler diagnoses that first, and it's better not to drive it: the transmission is losing pressure.

It's guidance: a technician with a scan tool makes the final diagnosis.

See every step and resultShow
  1. Step 1. Is P0944 (pump lost prime) set too?Yes: «The pump lost pressure» · No: step 2
  2. Step 2. Are P0732, P0734 or P0846 set too?Yes: «Solenoid and range sensor assembly» · No: step 3
  3. Step 3. Is there a calibration or software update for your model?Yes: «Calibration or software» · No: step 4
  4. Step 4. Are the OD switch signal wire and the transmission relay output OK, with no opens or shorts to ground or power?Yes: step 5 · No: «Repair the wiring»
  5. Step 5. At the shop, do the computer and wiring pass the simulator test?Yes: «Inspect the valve body» · No: «The computer»

Results

  • The pump lost pressure. With P0944, before the pump Chrysler checks the shifter adjustment, the fluid level, the filter (broken, plugged or misinstalled, and its seal seated in the pump), on RFE units the external cooler return filter, and that the main regulator valve isn't sticking.
  • Solenoid and range sensor assembly. On the 62TE, if P0870 sets with P0732, P0734 or P0846, Chrysler replaces the solenoid/range sensor assembly directly and then runs the quick learn with the scan tool.
  • Calibration or software. Ask the dealer for the update for your VIN. On the 2018 Ram 2500 and 3500 with the 68RFE (US), if P0870 is the only code, Chrysler asks not to replace solenoids, the pressure sensor, the valve body or the transmission: clear the code and, if it returns, apply the calibration.
  • Repair the wiring. Repair the open or shorted switch signal wire, or the transmission relay output, before replacing parts, then clear the code and test again.
  • Inspect the valve body. If the computer and wiring pass the test, Chrysler disassembles and inspects the valve body before replacing the solenoid assembly. On the 62TE, the computer tests the switch by briefly applying the OD clutch after each shift, above 1,000 rpm.
  • The computer. If it fails the simulator test and the wiring is OK, the problem points to the computer: check it before opening the transmission.
Diagnostic tip

On the 2018 Ram 2500 and 3500 with the 68RFE (US), if P0870 is the only code, Chrysler asks not to replace solenoids, the pressure sensor, the valve body or the transmission: clear the code and, if it returns, look for the calibration update. On the 62TE, the computer tests the switch by briefly applying the OD clutch after each shift, above 1,000 rpm.

Can I drive with this code?

If the transmission is in limp mode, drive slowly and only to the shop; if it sets with P0944, better not to drive it: the transmission is losing pressure.

What carmaker bulletins say13 carmaker bulletins and the vehicles they nameShow

13 service bulletins published by the US NHTSA mention this code, mostly from RAM, Chevrolet, GMC, Mercedes-Benz, Utilimaster (2001–2019 models). The repair they mention most: updating the computer software.

Vehicles with service bulletins for this code

  • RAM 2500 2017–2019
  • RAM 3500 2017–2019
  • Mercedes-Benz Mercedes-Benz
  • Chevrolet Silverado 2001–2003
  • GMC Sierra 2001–2003
  • GMC Sierra 2500 2001–2003
  • Chevrolet Silverado 2500 2002–2003
Bulletin 9004016 · 2019
RAM 3500 2018 · RAM 2500 2018

68RFE setting only P0870: do not replace a solenoid, pressure sensor, transmission or valve body; it is a pending calibration issue. Reset the code and contact tech support if it returns.

Open the bulletin (PDF), page 1 ↗
Bulletin 18-040-17 REV. A · 2017
RAM 2500 2017 · RAM 3500 2017 · RAM 4500 2017 · RAM 5500 2017

6.4L engine: PCM reprogramming; includes optional 'MDS NOISE' software for drone, shudder or vibration at light throttle in MDS/ECO mode.

Open the bulletin (PDF), page 3 ↗
Bulletin 18-040-17 REV. A · 2017
RAM 5500 2017 · RAM 2500 2017 · RAM 4500 2017 · RAM 3500 2017

6.4L engine: PCM reprogramming; includes optional 'MDS NOISE' software for drone, shudder or vibration at light throttle in MDS/ECO mode.

Open the bulletin (PDF), page 3 ↗

These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.

TSS parts for the transmissions in these bulletins

Buy in

Different transmission? Pick it and we'll show its parts:

See parts →

Find the part by its number on the exploded diagram: 45RFE

Related codes

← See all codes

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.