Harsh shift and/or MIL on with DTCs P0750, P0755, P0758 and/or P1760.
Code P0750: Shift solenoid A malfunction
A fault in a shift solenoid (A, B, C, D or E) or its circuit, or the solenoid doesn't do what the computer commands. The transmission usually stays in one gear.
Shift solenoid
A loose, dirty or wet connector
Only as far as the shop
What car do you have?
Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.
Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →
Symptoms
- Limp modeIt stays in one gear (2nd on Chrysler 4-speeds, 3rd on Nissan RE4F03 units) or, on the 6R80, uses only 5th and 6th.
- It doesn't shift, or only makes some shifts
- Check engine light on, sometimes with other solenoid codes when the fault is in something they share
- On the 42RLE (Liberty, Wrangler), if the code sets above about 22 mph the transmission may go to neutral
Most common causes
- 1A loose, dirty or wet connectorFord documented it at the solenoid body connector on the 2002 Explorer, and Chrysler on 2003–2005 Liberty, Wrangler and Dakota (US).
- 2A broken or shorted wire between the computer and the transmission
- 3The internal harness or lead frameFord allows replacing a single solenoid, the harness or the lead frame without replacing the whole solenoid body.
- 4The power feedOn Chryslers all solenoids are fed by the same relay, and on the 1999 Windstar (US) Ford tied P0750 and P0760 to blown fuses.
- 5Shift solenoid A itself, which varies by makeOn Chrysler it's the LR (low/reverse) solenoid; on Ford, SSA; GM and Honda don't use P0750 (their electrical fault shows as P0973–P0977).
- 6The computer, last
From most common and easiest to check to least common.
Follow these steps
Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.
Are other solenoid codes set along with P0750, such as P0755 or P0760?
It's guidance: a technician with a scan tool makes the final diagnosis.
See every step and resultShow
- Step 1. Are other solenoid codes set along with P0750, such as P0755 or P0760?Yes: «Check what they share» · No: step 2
- Step 2. Are the transmission fuses good?Yes: step 3 · No: «Blown fuse»
- Step 3. Is the transmission connector clean, dry and tight, with no corrosion or loose terminals?Yes: step 4 · No: «Repair the connector»
- Step 4. With the scan tool connected, does the code or the reading change when you move the harness?Yes: «Bad contact» · No: step 5
- Step 5. Are the wires between the computer and the transmission OK, with no opens or shorts, and is the relay's power getting through?Yes: step 6 · No: «Wires or power feed»
- Step 6. Measured at the transmission connector, is solenoid A's coil within your transmission manual's value?Yes: «The computer, last» · No: «Internal harness or solenoid A»
Results
- Check what they share. When several solenoid codes set, the likely cause is something they share (power feed, ground, connector, harness or computer), not two solenoids at once. Chrysler checks the power feed codes first, and Hyundai documented P0750, P0755, P0760 and P0765 together with the transmission held in 3rd (US).
- Blown fuse. Replace the fuse and find out why it blew before testing further: if there's a short, it will blow again. Then clear the code and test again.
- Repair the connector. Clean, dry and repair the connector and its terminals, then clear the code and test again before replacing solenoids.
- Bad contact. If the code changes when you move the harness, that's where the fault is: find the damaged connector or section and repair it.
- Wires or power feed. Repair the broken or shorted wire between the computer and the transmission, or the relay's power feed, before touching the solenoid.
- Internal harness or solenoid A. If it measures wrong at the transmission connector, the fault is inside: the internal harness, the lead frame or solenoid A. Ford allows replacing a single solenoid, the harness or the lead frame without replacing the whole solenoid body. A varies by make: on Chrysler it's the LR solenoid; on Ford, SSA. Afterwards, do the relearn the carmaker requires.
- The computer, last. With the fuses, connector, wires and solenoid OK, check the computer, always last. Then clear the code with a scan tool, not by disconnecting the battery, and drive a few cycles through every gear to confirm.
Run the solenoid activation test with the scan tool and measure the coil from the case connector against that transmission's spec (for example, 20–30 Ω on Ford's 4R70W and on solenoid A of Nissan's RE4F03). If P0750 and P0755 set together, check what they share first: power feed, relay, connector and harness.
Only as far as the shop: the transmission goes into a limp mode that varies by unit, and some can drop into neutral while moving.
What carmaker bulletins say16 carmaker bulletins and the vehicles they nameShow
16 service bulletins published by the US NHTSA mention this code, mostly from Hyundai, Toyota, Santa Fe, Ford, Jeep (1996–2023 models).
Vehicles with service bulletins for this code
- Hyundai Elantra 1996–2007
- Hyundai Tiburon 1997–2008
- Toyota RAV4 2001–2003
- Ford Windstar 1999
- RAM 4500 2023
- RAM 3500 2023
- Jeep Wrangler 2003–2005
- Dodge Dakota 2004–2005
Toyota service campaign: harsh automatic transaxle shift and/or check engine light with DTCs P0750, P0753, P0755, P0758 and/or P1760.
Open the bulletin (PDF) ↗Harsh shift and/or MIL on with DTCs P0750, P0753, P0755, P0758 and/or P1760 on 4-speed automatic transaxles.
These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.
TSS parts for this code
Pick your transmission to see the TSS parts that fit it, or open all parts of this type:
Buying wholesale or own a parts store?
We'll send you a quote or tell you how to sell TSS in your area.