Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
System: Shift solenoid

Code P0974: Shift solenoid A control circuit high

A fault in a shift solenoid (A, B, C, D or E) or its circuit, or the solenoid doesn't do what the computer commands. The transmission usually stays in one gear.

What's failing

Shift solenoid

Most common cause

A short to voltage

Can I drive with this code?

It can be driven carefully to the shop

Diagnosis for your car

What car do you have?

Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.

Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →

Symptoms

  • Check engine light on and odd shiftingThe transmission may lose some gears or go into limp mode.
  • On GM's 2006 4T65-E, it switches to an alternate shift pattern
  • On Hino trucks (US), low power and erratic shifts along with other solenoid codes

Most common causes

  1. 1A short to voltageOn the 4L60E, GM sets it for a continuous short to power in the solenoid A circuit.
  2. 2An open circuitOn Honda, P0974 is shift solenoid A circuit open.
  3. 3The transmission or solenoid connector, loose, dirty or wet, or a chafed harness
  4. 4Power and groundsOn Hino trucks (US), these codes set from low voltage between the transmission case and the battery post.
  5. 5The solenoid winding or, last, the computer

From most common and easiest to check to least common.

Step-by-step diagnosis

Follow these steps

Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.

Step 1

Are other solenoid codes set along with P0974?

It's guidance: a technician with a scan tool makes the final diagnosis.

See every step and resultShow
  1. Step 1. Are other solenoid codes set along with P0974?Yes: «Check what they share» · No: step 2
  2. Step 2. Are the transmission and solenoid connectors clean, dry and tight, and the harness free of chafing?Yes: step 3 · No: «Connector or harness»
  3. Step 3. With the scan tool connected, does the code or the reading change when you move the harness?Yes: «Bad contact» · No: step 4
  4. Step 4. Following your vehicle's manual, is the solenoid A circuit OK, with no short to power and no open?Yes: step 5 · No: «Short to power or open circuit»
  5. Step 5. Are the power feed and grounds OK, with no low voltage between the transmission case and the battery post?Yes: step 6 · No: «Power feed or grounds»
  6. Step 6. Measured at the connector, is solenoid A's coil within your transmission manual's value?Yes: «The computer, last» · No: «Replace solenoid A»

Results

  • Check what they share. First check the power feed, grounds, connector and harness they share. On Hino trucks (US), several solenoid codes set at once, with low power and erratic shifts, from low voltage between the transmission case and the battery post.
  • Connector or harness. Clean, dry or repair the connector and the chafed harness, then clear the code and test again.
  • Bad contact. If the code changes when you move the harness, that's where the fault is: find the damaged connector or section and repair it.
  • Short to power or open circuit. Repair the wire shorted to power or open between the computer and the solenoid before replacing parts, then clear the code and test again.
  • Power feed or grounds. Repair the power feed and grounds, including the connection between the transmission case and the battery post, then clear the code and test again.
  • Replace solenoid A. With the connector, harness and power feed OK and the winding out of spec, replace shift solenoid A and do the relearn the carmaker requires.
  • The computer, last. With the connector, harness, power feed and solenoid OK, check the computer, always last.
Diagnostic tip

"High" doesn't always mean the same thing: GM uses it for a short to voltage and Honda for an open circuit, so follow your vehicle's manual for what to measure. Start with the connector and harness; it's an electrical code, not a fluid code.

Can I drive with this code?

It can be driven carefully to the shop; if the transmission stays in one gear or slips, drive slowly and as little as possible.

What carmaker bulletins say2 carmaker bulletins and the vehicles they nameShow

2 service bulletins published by the US NHTSA mention this code, mostly from Hino (2012–2015 models).

Bulletin 167-T1513-12 · 2015
Hino Xjc 2012–2015 · Hino Ne8j 2012–2015 · Hino Nv8j 2012–2015 · Hino Xfc 2012–2015

COE trucks with P0974 and P0986, sometimes with low power and erratic shifts. These codes may set from low voltage between the transmission case and the battery post.

Open the bulletin (PDF), page 3 ↗
Bulletin TT-15-014 · 2015
Hino Conventional Models 2012–2015

COE trucks with P0974–P0986, sometimes with low power and erratic shifts. These codes may set from low voltage between the transmission case and the battery post.

Open the bulletin (PDF), page 3 ↗

These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.

TSS parts for this code

Pick your transmission to see the TSS parts that fit it, or open all parts of this type:

See parts →

Related codes

← See all codes

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.