Only 2017 Journeys built in June 2017 with P0755: replace the solenoid (5140429AA) and transmission harness (68080261AF) without disconnecting them from each other, and send them for analysis.
Open the bulletin (PDF), page 1 ↗Code P0755: Shift solenoid B malfunction
A fault in a shift solenoid (A, B, C, D or E) or its circuit, or the solenoid doesn't do what the computer commands. The transmission usually stays in one gear.
Shift solenoid
A loose, dirty or damp transmission connector
Only as far as the shop
What car do you have?
Pick your car and we'll tell you which transmission it has, which TSS parts fit it for this code, and whether there are bulletins for your model.
Can't find your car, or not sure which transmission it has? We'll help you identify it. Ask us →
Symptoms
- Limp modeIt stays in one gear (2nd on Chrysler 4-speeds, 3rd on Nissan RE4F03 and Hyundai 4-speed units).
- Some shifts are missing, or it doesn't shift at all
- Check engine light on, often together with P0750 or other solenoid codes
- Harsh engagement if the computer raises pressure to maximum to protect itself (for example, a 4L60E with a fault in the B circuit)
Most common causes
- 1A loose, dirty or damp transmission connectorOn heavy-duty Ram pickups (US), Stellantis found many solenoid packs replaced for P0755 and P0765 had nothing wrong.
- 2A broken or shorted wire between the computer and the transmission
- 3The internal harness or lead frame (Ford allows replacing them separately)
- 4The power feedOn Chryslers, all solenoids share the same relay and fuse.
- 5Shift solenoid B, which varies by makeOn Chrysler it's the 2-4 solenoid (2C on RFE units); on Ford, SSB; GM and Honda don't use P0755 on their recent units.
- 6The computer, last
From most common and easiest to check to least common.
Follow these steps
Answer yes or no and we'll tell you what to check next, in the order of the carmakers' manuals.
Is P0750 or another solenoid code set too?
It's guidance: a technician with a scan tool makes the final diagnosis.
See every step and resultShow
- Step 1. Is P0750 or another solenoid code set too?Yes: «Check what they share» · No: step 2
- Step 2. Unplugged and cleaned, is the transmission connector dry and tight, with no loose, corroded or pushed-out terminals?Yes: step 3 · No: «Clean and repair the connector»
- Step 3. With the scan tool connected, does the code or the reading change when you move the harness?Yes: «Bad contact» · No: step 4
- Step 4. Are the fuse, relay and wires between the computer and the transmission OK, with no opens or shorts?Yes: step 5 · No: «Fuse, relay or wires»
- Step 5. Measured at the transmission connector, is solenoid B's coil within your transmission manual's value?Yes: «The computer, last» · No: «Internal harness or solenoid B»
Results
- Check what they share. If it sets together with P0750, the likely cause is something they share (power feed, relay, ground, connector or harness), not two solenoids at once. Chrysler checks the power feed codes first.
- Clean and repair the connector. Clean or repair the terminals and apply dielectric grease to the connector, as Stellantis asks, then clear the code and test again before replacing the solenoid pack.
- Bad contact. If the code changes when you move the harness, that's where the fault is: find the damaged connector or section and repair it.
- Fuse, relay or wires. Repair the broken or shorted wire, or the relay's power feed and its fuse, before touching the solenoid. If the fuse had blown, find out why before testing.
- Internal harness or solenoid B. If it measures wrong at the transmission connector, the fault is inside: the internal harness, the lead frame (Ford allows replacing them separately) or solenoid B, which is the 2-4 solenoid on Chrysler (2C on RFE units) and SSB on Ford. On the 2017 Journey with P0755, Chrysler said to replace the solenoid and the harness.
- The computer, last. With the connector, harness, power feed and solenoid OK, check the computer, always last. Then clear the code with a scan tool and drive a few cycles through every gear to confirm.
Before replacing the solenoid pack, unplug, clean and inspect the transmission connector and wiggle the harness with the scan tool connected. If it sets together with P0750, the likely cause is something they share (power feed, relay, connector, harness), not two solenoids at once.
Only as far as the shop: the transmission stays in limp mode and, depending on the unit, may engage harshly or lose gears.
What carmaker bulletins say33 carmaker bulletins and the vehicles they nameShow
33 service bulletins published by the US NHTSA mention this code, mostly from RAM, Hyundai, Dodge, Toyota, Santa Fe (1996–2023 models).
Vehicles with service bulletins for this code
- RAM 2500 2019–2023
- RAM 3500 2019–2023
- Hyundai Elantra 1996–2007
- Hyundai Tiburon 1997–2008
- Dodge Journey 2017
- Toyota RAV4 2001–2003
- Jeep Wrangler 2003–2005
- Dodge Dakota 2004–2005
Only 2017 Journeys built in June 2017 with P0755: replace the solenoid (5140429AA) and transmission harness (68080261AF) without disconnecting them from each other, and send them for analysis.
Open the bulletin (PDF), page 1 ↗With DTC P0755, contact engineering with the freeze frame data before replacing parts; if there is no response, repair by replacing the solenoid and the harness.
Open the bulletin (PDF), page 1 ↗With DTC P0755, contact engineering with the freeze frame data before replacing parts; if there is no response, proceed with the repair.
Open the bulletin (PDF), page 1 ↗These are US bulletins: check with your dealer or shop whether they apply to your car. Bulletins open on NHTSA's site, at the page where the repair starts.
TSS parts for this code
Pick your transmission to see the TSS parts that fit it, or open all parts of this type:
Buying wholesale or own a parts store?
We'll send you a quote or tell you how to sell TSS in your area.