
- On a Honda, P0780 isn't one fault: it depends on the transmission. On the Accord 2.4 and CR-V 5-speeds it's a summary code that comes with another one, from P1730 to P1734.
- On the V6 5-speeds, Honda ends with shift valve D or the transmission; on the 4-speeds, it replaces the solenoids the code names before the transmission.
- In Mexico it's set by the 1998 to 2012 Accord (the V6 only through 2007), the 2002 to 2014 CR-V, the 2001 to 2006 Odyssey, the 2003 to 2008 Pilot and the 2004 and 2005 Civic; newer Hondas use other codes.
- Honda first checks the fluid with a strainer: metal debris or a lot of clutch material means a transmission. Its shift solenoids measure 12 to 25 Ω, and the linear ones 3 to 10 Ω.
- The recall, extended warranty and class action we found are US programs; we found no campaigns in Mexico.
In Mexico, code P0780 is searched mostly with Honda: early-2000s CR-Vs, Accords and Odysseys. What's out there in Spanish describes it as a generic shift fault or as "solenoid C". Honda's service manuals are more precise, and the answer depends on the transmission: on some it's a summary code, on others a problem with one shift valve, and on others a hydraulic fault of named solenoids. This guide pulls together what Honda's manuals and bulletins say: what it means on each transmission, which Hondas set it in Mexico, what Honda checks, limp mode, bulletins, myths and TSS parts. If you have another code, look it up in our diagnosis by code.
What does code P0780 mean?
By the standard, P0780 is a general shift fault, and P0781 to P0784 cover each shift: 1-2, 2-3, 3-4 and 4-5. Honda gives it a different meaning depending on the transmission:
| Honda transmission | What P0780 means |
|---|---|
| 4-cylinder 5-speeds: 2003 to 2012 Accord 2.4, 2005 to 2014 CR-V and Acura TSX | "Shift Control System": a summary code Honda stores when another one from P1730 to P1734 is stored (stuck shift or linear solenoids, or stuck shift valves). If it shows up alone, Honda updates the computer's software or tries a known-good one |
| V6 5-speeds: 2003 Accord V6, 2005 Odyssey and 2006 Pilot (US manuals) | "Problem in Shift Control System": after checking the fluid, Honda repairs shift valve D or replaces the transmission |
| 4-speeds (1998 Accord 2.3, 2001 Odyssey, 2004 CR-V) and the 2003 Pilot | "Mechanical problem in hydraulic control system" of named solenoids: Honda replaces those solenoids, resets the computer and, if the code comes back, replaces the transmission |
| 2004 and 2005 Civic 1.7 automatic | "Problem in Shift Control System": the stall test decides between the lower valve body and the transmission |
| 2006-on Civic, 2007-on Odyssey, 2008-on Accord V6, 2009-on Pilot and the Fit | They don't use it: they have per-gear and per-solenoid codes, such as P0731 to P0735 or P0751 to P0777 |
Outside Honda, each maker uses it its own way. Mazda's bulletin mentions Mexican versions; the rest are US documents. More in our Mazda, 4R70W and Dodge, Jeep and RAM guides:
| Make and transmission | What it means |
|---|---|
| Mazda SKYACTIV-Drive (Mazda2, 3 and 6, CX-3, CX-5 and CX-9) | "Gear shifting malfunction", often with P1738: pressure switches A and B on the valve body stick from contamination. Mazda reprograms the module or replaces both switches, and its bulletin covers Mexico-spec versions |
| Ford 4R70W and 4R75E (Lobo/F-150, Grand Marquis) | It uses P0781, P0782 and P0783: no rpm drop when the computer commands the 1-2, 2-3 or 3-4 shift. Ford checks the shift solenoids and internal parts |
| 2018 and 2019 Jeep Compass and Renegade and Fiat 500X 9-speeds | "Gear Shift Malfunction": limp mode, a bump and rpm jumping to 4,000. FCA reprograms the transmission module |
| 2021 Nissan Rogue and 2022 and 2023 Mitsubishi Outlander CVTs | "Shift error": transmission and electronic shifter software; on the Outlander, an intermittent contact in the position switch. Mitsubishi warns not to replace the CVT for it |
| Toyota AB60F (2007 to 2009 Tundra and Sequoia) | It lists P0781 among the C1 clutch damage codes |
| GM, Hyundai, Kia, Toyota Corolla, VW and Chrysler front-drive units | It isn't in the code lists we checked |
Which Hondas set it in Mexico?
| Honda in Mexico | Does it use P0780? |
|---|---|
| Accord 1998 to 2002 (2.3 and V6, 4-speed) | Yes |
| Accord 2.4, 2003 to 2012 (5-speed) | Yes, as a summary of codes P1730 to P1734 |
| Accord V6, 2003 to 2007 | Yes |
| Accord V6, 2008 to 2012 | No |
| CR-V 2002 to 2014 | Yes: on the 4-speeds (2002 to 2004) as a hydraulic fault, and on the 5-speeds as a summary of P1730 to P1734 |
| Odyssey 2001 to 2006 | Yes |
| Pilot 2003 to 2008 | Yes |
| Civic 1.7, 2004 and 2005 | Yes; the 2001 Civic doesn't use it, and we didn't check 2002 and 2003 |
| Odyssey 2007 on, Pilot 2009 on, Civic 2006 on and Fit 2009 to 2013 | No |
| Acura TL 2005 to 2008, MDX and TSX | Depends on the year: the 2004 TL, 2005 MDX and 2009 TSX do; the 2008 TL and 2007 MDX don't |
| Hondas with a CVT | No: they use their own codes |
Honda de México doesn't publish each transmission's code: we infer it from Honda's US manuals for the same transmission, so it's worth confirming against your scan tool's code list. The 2010 to 2013 City was only sold in Mexico and has no US manual. The transmission number is stamped on the case, next to the engine number. To find out which transmission your Honda has, see our Honda transmission guide.
What does the car do with P0780?
On the 4-cylinder 5-speeds, Honda stores a temporary code the first time and turns on the check light if the fault repeats on the second drive cycle; the D light also blinks. The check light goes off after three consecutive trips without the fault. In the owner's manual, Honda says a blinking D means a possible transmission problem.
With the check light or the D light on, 1998 to 2004 Hondas can go into limp mode, which varies with the transmission and the code: harsh shifts, starting in 2nd and shifting to 3rd or 4th, and little power when accelerating. In the version of one of these transmissions that GM used in the Saturn VUE V6, GM explains it this way: the transmission drops from 3rd to 2nd when the computer commands 4th; GM checks shift valve D and the pressure regulator valve, and meanwhile the transmission only uses 2nd and 3rd.
How does Honda diagnose it?
This is the order in Honda's US service manuals (2003 Accord, 2005 Odyssey, 2003 and 2006 Pilot, 2004 CR-V and 2004 Civic):
- Save the freeze frame, clear the codes and do two test drives in D, going through every gear above 20 km/h (12 mph) for more than 20 seconds each. Honda says not to judge the transmission with the check light or the D light on.
- If another transmission code shows up, handle it first.
- Warm the engine until the fan comes on, check the level and for leaks, and drain the fluid through a strainer. If it has metal debris or a lot of clutch material, Honda replaces the transmission; if not, it changes the fluid and tests again.
- Test the shift solenoids with Honda's scan tool (they should click) and measure them: 12 to 25 Ω.
- Measure the linear solenoids, which control clutch pressure: 3 to 10 Ω, and the valve should move freely. On the Accord 2.4, Honda replaces B and C together.
- If a shift solenoid doesn't click with the scan tool but tests good on the bench, Honda replaces the solenoid harness.
- Last, depending on the transmission: shift valve D, the lower valve body or the transmission. If P0780 shows up alone on a 4-cylinder 5-speed, Honda updates the computer's software.
On the 2004 and 2005 Civic, Honda uses the stall test in D: above 3,500 rpm it replaces the transmission; below 2,000 rpm, the lower valve body; and in between, it compares engine rpm with vehicle speed at 50 km/h (30 mph). On the 2004 CR-V 4-speed it first replaces linear solenoids A, B and C, then shift solenoids A, B, C and E, resets the computer by pulling the ECU fuse for more than 10 seconds and drives five times; if it persists, it overhauls the hydraulic control and, last, replaces the transmission.
The 2nd and 3rd clutch pressure switches have their own codes (P0842, P0843, P0847 and P0848), and Honda notes they're electrical faults, not mechanical ones. If your Honda is one that doesn't use P0780, see our guides to codes P0731 to P0735, shift solenoids and pressure control solenoids.
After replacing solenoids or the transmission
On the 2003 and 2004 Accord V6 and the 2002 to 2004 Odyssey, Honda warned in 2004 that crossing the connectors of linear solenoid C and shift solenoid A, when replacing solenoids or the transmission, causes P0780: the transmission won't upshift or stays in 2nd. Check the wire colors before plugging them in. On the 2003 Accord V6, Honda also updates the computer's software when installing a remanufactured transmission. And when installing a remanufactured transmission, it calls for cleaning the fluid cooler, fitting the new in-line filter (removing the old one, if there was one) and not reusing the heater or cooler from the failed transmission.
Are there bulletins or campaigns?
| Program (US) | What Honda did |
|---|---|
| 2004 recall: 2003 and 2004 Accord V6, 2002 to 2004 Odyssey, 2003 and 2004 Pilot and several Acuras | Heat between the 2nd gears could break them and lock up the transmission. Under 15,000 miles, a revised cooler return line; above that, an inspection and a new transmission if there was discoloration. It doesn't mention P0780 |
| 2002 warranty extension: 2000 and 2001 Accord, Odyssey and Prelude, Acura TL and CL | Seven years or 100,000 miles on the automatic transmission, for premature wear or failure; Honda mentioned slow or erratic shifting |
| Campaign 04-060: 2002 to 2004 Odyssey | A new computer for erratic or harsh shifting, including vehicles that already had a remanufactured transmission |
| "Third Clutch" class action in California: 2003 and 2004 Accord V6, 2002 to 2004 Odyssey, 2003 and 2004 Pilot | Settlement for owners living in California: reimbursement for parts of a replaced transmission or a voucher. The suit alleged a 3rd-clutch defect; Honda denied it |
These are US programs; we found no Honda de México campaigns or Profeco alerts for these transmissions.
Which fluid does it take?
Honda ATF DW-1, which replaced ATF-Z1 in 2010. Honda says to use only its ATF, because another can affect shift quality; in the 2004 Accord manual, Dexron III was only a temporary substitute. The level is checked hot, on level ground with the engine off, within 60 to 90 seconds of shutting it off. On the 2003 Accord 2.4, a fluid change takes 2.9 liters of the transmission's 6.5, so a single drain changes less than half. Honda doesn't recommend flush machines: it drains and refills several times.
P0780 myths
- "P0780 is shift solenoid C." On Honda it's a general code: on the 4-cylinder 5-speeds it summarizes P1730 to P1734, and on the 2003 Pilot it names shift solenoid A and linear solenoids A and B.
- "With P0780 the transmission has to be replaced." Honda replaces it last, after checking the fluid and the strainer, testing the solenoids or updating the software. The exception is finding metal debris or a lot of clutch material in the strainer.
- "It's a misfire or the engine coolant temperature sensor." No Honda P0780 diagnosis mentions that; the V6 one only asks to warm the engine to 80 °C (176 °F) before testing.
- "In limp mode it always stays in 2nd." Honda says it depends on the transmission and the code: commonly it starts in 2nd and shifts to 3rd or 4th, with harsh shifts.
- "Honda solenoids come out without removing anything." The linear ones are outside, but on the 2003 Accord 2.4, to reach the shift solenoids Honda removes the battery and its base, supports the transmission with a jack and removes the solenoid cover.
- "Clear the code and you're done." Honda stores a temporary code and turns on the check light if the fault repeats; its own diagnostics clear and test twice to see if it comes back.
- "I replaced the solenoids and P0780 is still there: the transmission is done." On that era's Accord V6 and Odyssey, crossed connectors cause exactly that; check the wire colors.
- "P0780 means the same on every make." Honda, Mazda, Chrysler, Nissan and Mitsubishi give it different causes, and Ford uses one code per shift.
- "The 2004 recall or the extended warranty covers P0780 in Mexico." They're US programs, and the recall was about the 2nd gears, not this code.
TSS parts for P0780
The Honda page has every TSS part for these transmissions. These are the ones that match the jobs in this guide:
| Transmission and job | TSS part |
|---|---|
| 2003 to 2012 Accord 2.4 and 2005 to 2014 CR-V: solenoids | Linear solenoid pair, linear solenoid and shift solenoid B, black connector |
| 1998 to 2007 Accord and Odyssey: solenoids | Shift solenoid, brown connector, solenoid A, single linear solenoid and linear solenoid pair |
| 1998 to 2002 Accord V6 and 1999 to 2001 Odyssey | Lock-up solenoid pair |
| 2006 to 2008 Pilot | Brown shift solenoid A |
| 2001 to 2005 Civic | Linear solenoid pair and solenoid A |
| 2nd and 3rd clutch pressure switches | Double switch with housing and 33 PSI switch |
| Filters | Accord 2.4 and CR-V 5-speed filter, B90A and B5RA filter and in-line filter |
| Transmission overhaul | TSS Rojo gasket kits BCLA, 2003 on, V6 BAYA and B7WA and Civic BMXA |
The four-letter transmission codes (BCLA, BAYA, BMXA and others) come from parts catalogs: Honda de México doesn't publish them. Confirm with your distributor using the transmission number or the car's VIN. If you're torn between the Rojo and Dorado kits, read how they differ, and to test other solenoids, see our transmission solenoid guide.
TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.
Solenoides Dobles Lineales con empaque MRMA, BCLA, MRVA, MCLA, MCTA, M4TA, MDMA, MDLA, MCVA, MZKA
Solenoide Lineal Honda Varios BCLA
Solenoide de Cambio Conector Marron BAXA MAXA B7XA B7TA BAYA BGHA BYBA B7WA B6VA
Solenoide Cambios A Negro Varios Honda (Lockup Civic 2001/05 BMXA SLXA)
SOLENOIDE LINEAL SENCILLO BAYA, MAYA, BGHA, MGHA, BYBA, B7WA, M7WA
Solenoide Lineal Doble Honda Acura con Empaque
SWITCH DOBLE CON HOUSING BAXA
Switch Presion 2da-3ra 33 PSI (Conector Negro Escalonado) B7XA BAXA BVGA MGHA BYBA PVGA MAXA



