
- P0842, P0843, P0847 and P0848 are transmission pressure codes, but each maker assigns the letter to a different part: clutch switches on Honda, valve body switches on Mazda, CVT sensors on Nissan and module switches on GM.
- On Honda (Civic, Fit, CR-V, Accord) they're the 2nd clutch switch (P0842 and P0843) and the 3rd (P0847 and P0848), and Honda says the fault is electrical, not mechanical.
- On Mazda SKYACTIV, the switches stick from contamination: Mazda reprograms the module or replaces both switches, and its bulletin covers Mexican versions.
- On the 2013 to 2019 Sentra and the 2015 to 2022 X-Trail it's the secondary pressure sensor; Nissan's US bulletins replace the valve body, not the CVT.
- On GM's 6T40 and 6L80 they don't turn on the check engine light; GM cleans and tests the module before replacing it.
In Mexico, codes P0842, P0843, P0847 and P0848 are searched mostly with Honda (Civic, Fit, CR-V), the Nissan Sentra and X-Trail, and the Mazda CX-5. By the standard they're "pressure sensor or switch A or B circuit, low or high", but each maker assigns the letter to a different part, which is why what's online confuses more than it helps. This guide pulls together what each maker's manuals and bulletins say: which part it is, which vehicles set them in Mexico, how they're diagnosed and which TSS parts fit. If you have another code, look it up in our diagnosis by code.
What do these codes mean on each make?
| Make and transmission | Which part it is |
|---|---|
| Honda 5-speed automatics | P0842 and P0843: 2nd clutch pressure switch. P0847 and P0848: the 3rd clutch switch. The V6 units also use P0872 and P0873, for the 4th clutch switch |
| Honda CR-V 2002 to 2004 (4-speed) | It uses others: P0840 (2nd) and P0845 (3rd) |
| Mazda SKYACTIV-Drive (Mazda2, 3 and 6, CX-3, CX-5 and CX-9) | P0842 and P0843: oil pressure switch No. 1 (part of switch B). P0847 and P0848: No. 2 (switch A). Codes ending in 2 or 7 mean "stuck on", and those ending in 3 or 8, "stuck off" |
| Nissan JF015E CVT (Sentra 2013 to 2019, Note) | P0846, P0847 and P0848: secondary pressure sensor, inside the valve body |
| Nissan JF016E CVT (X-Trail/Rogue 2015 to 2022, Altima 2.5 2013 to 2018) | P0847 and P0848: secondary pressure sensor. P084C and P084D: the primary pressure sensor |
| Nissan JF011E CVT (Sentra 2007 to 2012, X-Trail 2008 to 2014) | It uses others: P0840 (secondary) and P0845 (primary) |
| Jeep Compass and Patriot and Dodge Caliber, with the same JF011E CVT | P0842 and P0843: primary pressure sensor. P0847: the secondary pressure sensor |
| GM 6T40 and 6T45 (Cruze, Sonic, Trax, Equinox, Malibu) and 6L80 | Switches inside the transmission module. On the 6T40: P0842 and P0843, pressure switch 1 (3-5-R clutch); P0872 and P0873, switch 3 (2-6 clutch); and P0877 and P0878, switch 4 (1-2-3-4 clutch). On the 6L80, P0842 and P0843 are switch 1 too |
| Toyota U660E | It uses P0872 and P0877 for its pressure switches No. 1 and No. 2 |
That's why "pressure sensor B" means nothing without the make and the transmission: on Nissan's JF011E CVT, B is the primary pulley sensor; on the JF015E and JF016E, the secondary. And on the same JF011E, Nissan and Chrysler use different numbers.
Which vehicles set them in Mexico?
| Vehicle in Mexico | Codes |
|---|---|
| Honda Civic 2006 to 2015, Fit 2009 to 2013, Accord 2.4 2003 to 2012 and CR-V 2007 to 2014 | P0842, P0843, P0847 and P0848 |
| Honda Accord V6 2003 to 2007, Odyssey 2005 and 2006 and Pilot 2006 to 2008 | P0847, P0848, P0872 and P0873 |
| Honda Accord V6 2008 to 2012, Odyssey 2007 to 2013 and Pilot 2009 to 2015 | P0842, P0843, P0847, P0848, P0872 and P0873 |
| Mazda3 2014 on, Mazda2 and CX-3 2016 on, CX-5 2013 on, Mazda6 2014 to 2021 and CX-9 2016 to 2023 | P0842, P0843, P0847, P0848, P0872, P0873, P0877 and P0878 |
| Nissan Sentra 2013 to 2019 and Note | P0846, P0847 and P0848 |
| Nissan X-Trail 2015 to 2022 and Altima 2.5 2013 to 2018 | P0847, P0848, P084C and P084D |
| Nissan Sentra 2020 on | P0845 to P0848, and P084A to P084D |
| Jeep Compass and Patriot 2007 to 2013 and Dodge Caliber with a CVT | P0842, P0843 and P0847 |
| Chevrolet Cruze, Sonic, Trax, Equinox and Malibu with the 6T40 or 6T45 | P0842, P0843, P0872, P0873, P0877 and P0878, with no check engine light |
| Nissan Versa 2012 to 2019 and March automatics | No: they're 4-speeds, without these sensors |
Makers don't publish these codes on their Mexican spec sheets: we infer them from the US manuals for the same transmission. The exception is Mazda, which lists Mexican versions in its bulletin (below).
What does the car do?
It depends on the make. On Honda, the D light blinks, and the check engine light comes on during the first drive cycle (2009 Fit), the second (2003 Accord) or never (P0872 on the 2008 Accord V6). On Mazda, the check light and the transmission light come on; the computer limits power and disables manual mode and i-stop, and with the stuck-off codes it also blocks the affected gear. On Nissan, the 2015 to 2022 X-Trail drives normally, and the 2013 to 2019 Sentra accelerates slowly. On GM's 6T40 and 6L80 the check light doesn't come on: the computer only freezes that clutch's adaptive learning.
Honda: an electrical fault
On its 5-speed automatics, Honda says it on every diagnostic page: "This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission." The switch is screwed into the outside of the case; on the 2003 Accord 2.4 you reach it by removing the intake duct. This is Honda's order:
- With the scan tool, check in the data list that the 2nd (or 3rd) clutch switch reads OFF when the transmission isn't in that gear.
- With the ignition off, unplug the switch and turn the ignition back on: if the reading changes to OFF, replace the switch.
- If it still reads ON, look for a short to ground in the wire between the switch and the computer.
- With P0843 or P0848 (switch open or stuck off), unplug the switch: there should be about 5 V at its connector. If there is, replace the switch; if not, check the wire to the computer.
- If everything checks good, Honda updates the computer's software or tries a known-good one.
The 2002 to 2004 CR-V 4-speed is different: with P0840 or P0845, Honda measures the switch (40 MΩ or more to ground with the engine off, and 0 V in that gear) and checks the clutch pressure before replacing it. More on these transmissions in our Honda transmission and code P0780 guides.
Mazda: switches stuck from contamination
In its bulletin 05-002/23 (May 2023), Mazda explains that P0842, P0847, P0872 and P0877, sometimes with P0780 or P1738, set when pressure switches A or B on the valve body stick, temporarily or permanently, from contamination entering their passage. Depending on the model and year, Mazda reprograms the transmission module or replaces both switches, A and B, and then runs the initial learning. The bulletin doesn't apply if the transmission is also slow to engage from N to D.
It's the only bulletin on this topic that names Mexico: it has calibrations for Mexican versions of the 2014 and 2015 Mazda3, the 2013 to 2021 CX-5 and the Mazda6, and it says that in Mexico the repair falls under the new-vehicle warranty. Replacing the switches means dropping the pan, and switch B sits under the strainer. Transmisiones Veinte 07 explains the FW6A-EL pressure switch codes (in Spanish); more in our Mazda guide.
Nissan: sensors inside the valve body
On Nissan CVTs they're 5 V pressure sensors. On the 2013 to 2019 Sentra (JF015E), P0847 sets with the secondary pressure sensor below 0.09 V for 5 seconds, and P0848 above 4.7 V. Nissan checks the 5 V supply and the wiring, and if they're fine it replaces the valve body, where the sensor is; its US bulletin NTB15-037f does the same for P0846, P0847 and P0848.
On the 2015 to 2022 X-Trail (JF016E), the manual ends with "replace transaxle assembly", but bulletins NTB15-087 for the Rogue (the US X-Trail) and the Altima say the opposite for P0847, P0848, P084C and P084D: "do not replace the CVT". Nissan replaces the valve body, flushes the cooler and loads the new valve body's calibration data. These are US documents. Transmisiones Veinte 07 explains code P0848 (in Spanish), and these transmissions' problems are in our Nissan CVT guide.
On the Jeep Compass and Patriot and the Dodge Caliber, with the same JF011E CVT as the 2007 to 2012 Sentra, Chrysler uses P0842 and P0843 for the primary pressure sensor (below 0.09 V or above 4.7 V for 5 seconds) and P0847 for the secondary. Chrysler checks for a 5.0 ± 0.2 V supply and, if the circuit is good, replaces the sensor in the valve body. More in our Jeep and Dodge CVT guide.
GM: switches inside the module
On the 6T40 and 6T45 (Cruze, Sonic, Trax, Equinox, Malibu) and the 6L80, the pressure switches are inside the transmission module, the solenoid assembly with the computer. Their codes are Type C: they don't turn on the check light, and the computer only freezes that clutch's adaptive learning. GM explains that normal debris in the fluid can set them intermittently without the driver noticing.
On the 6L80, GM first runs a cleaning routine with the scan tool, with the transmission at 70 to 90 °C (158 to 194 °F), and then checks that each switch toggles when 2nd and 5th are commanded; if one doesn't, it replaces the module and runs the relearn. In its US bulletin PI1131, for 2011 6T40 and 6T45 units, a non-working pressure solenoid in the module left the car with no 1st (with P0878) or no 2nd and 6th (with P0873), and GM replaced the module. More in our 6T40 and 6F50 and 6T70 guides.
Myths about these codes
- "P0847 is pressure sensor B on any car." Each maker assigns the letter to a different part, and it isn't even the same across Nissan CVTs.
- "Measure the sensor's resistance and replace it if it's off." No maker gives a resistance value: Honda tests the switch with the scan tool and by unplugging it, Nissan and Chrysler measure voltages, and Mazda checks each switch's state by gear.
- "It always turns on the check engine light." On GM's 6T40 and 6L80 it doesn't, and on the 2008 Accord V6, P0872 doesn't either.
- "It goes into limp mode and slips." It depends: the 2015 to 2022 X-Trail drives normally, the 2013 to 2019 Sentra accelerates slowly, and on GM it's usually not noticeable.
- "It causes overheating and higher fuel use." It's not in any manual or bulletin we checked.
- "With this code the transmission has to be replaced." Honda ends with the switch, the wire or the software; Mazda, with the switches or the valve body; GM, with the module; and Nissan's bulletins say "do not replace the CVT".
- "It's only electrical." On Honda, yes; on Mazda the cause is contamination in the switch passage, and GM says normal debris in the fluid can set it.
- "My Versa sets P0847." In Mexico, the 2012 to 2019 Versa is a 4-speed automatic; the Versa P0847 you see online is the US CVT Versa.
- "Reprogramming the Mazda is enough." Only on the years Mazda lists; if the code comes back, both switches are replaced.
TSS parts for these codes
These are the TSS parts that match the jobs in this guide:
| Job | TSS part |
|---|---|
| Honda V6 5-speeds (Accord V6 2003 to 2007, Odyssey 2002 to 2004, Pilot 2003 to 2005) and 4-speeds: 2nd and 3rd clutch switches | Double switch with housing and 33 PSI switch |
| Jeep Compass, Patriot and Caliber with a CVT: primary pressure sensor | JF011E primary pressure sensor |
| GM 6T40 and 6T45: module with the switches | Rebuilt module, 2014 on and first-generation module, 2008 to 2012 |
| First-generation GM 6T70 and 6L80 | Diaphragms to repair the module |
| Mazda SKYACTIV: when the pan comes off | FW6A-EL filter |
| Nissan Sentra 2013 to 2019 (JF015E): when replacing the valve body | Internal filter and pan gasket |
| Nissan X-Trail 2015 to 2022 (JF016E) | 2WD and 4WD filters |
Three things to watch. TSS's Honda switches are listed for the 4-speeds and the early V6 5-speeds (confirm your transmission code with your distributor); the TSS catalog has no switch for the Civic, Fit, CR-V and Accord 2.4. The primary pressure sensor is listed for Nissan: confirm it fits your Compass or Caliber. And GM considers the module's switches to have no serviceable parts, so the diaphragms are a module repair option, not GM's procedure. To test other solenoids, see our transmission solenoid guide.
TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.
SWITCH DOBLE CON HOUSING BAXA
Switch Presion 2da-3ra 33 PSI (Conector Negro Escalonado) B7XA BAXA BVGA MGHA BYBA PVGA MAXA
Modulo Control Transmision TCM Reconstruido 24268164 14/UP 6T40 6T45 6T30 6T50 con Solenoides Gen2,3
Diafragmas [5] Plastico Reparacion Modulo 6L45, 6L50, 6L80, 6L90 y 6T70, 6T75 GEN1
FILTRO FW6A-EL
FILTRO Interno JF015E RE0F11A
Empaque de Carter JF015E RE0F11A
Filtro Interno Bajo 2WD JF016E JF017E JF018E 2015/17



