
- The TH350 and TH400 are GM 3-speed automatics with a vacuum modulator; the 700R4 (1982 to 1993) was the first 4-speed with overdrive, and the 4L60E and 4L80E are the electronic versions that followed.
- The quickest check is counting the pan bolts: 13 on the TH350 (nearly square, with one corner cut off) and on the TH400 (irregular shape), 16 on the 700R4 and 4L60E, and 17 on the 4L80E.
- Other clues: the TH350 uses a kickdown cable and the TH400 an electric solenoid; the 700R4 has a TV cable, and the 4L60E and 4L80E have an electrical connector and no cable. The RPO code confirms it: MD8, M30 or MT1.
- In Mexico, GM spec sheets confirm the TH350 in the 1971 Impala and the 4L60E in the automatic 1997 Cheyenne, Silverado and Suburban, and several models with the 350 engine, like the 1977 C-10 and the 1984 Monte Carlo SS, were manuals.
- TSS has overhaul kits, filters, pan gaskets, bands, plates, bushings, solenoids and sensors for these transmissions.
If you have a classic rear-wheel-drive Chevrolet or GMC, like a C10 pickup, a Suburban, a Blazer, an Impala, a Malibu or a Camaro, and you're about to buy parts for its automatic transmission, first you need to know which one it has. GM's most common ones are the 3-speed TH350 and TH400, the 4-speed 700R4, and their electronic successors, the 4L60E and the 4L80E. The TH350, TH400 and 700R4 look alike from the outside, but they take different parts. Here's how to tell them apart by the pan, by their cables and connectors and by their code, which vehicles had them in Mexico, their best-known failures and which TSS parts fit them.
What's the difference between the TH350, TH400, 700R4 and 4L80E?
The TH350 and TH400 are 3-speed automatics with no overdrive, controlled by hydraulic pressure and a vacuum modulator; the TH400 is the heavy-duty one. The 700R4 was the first 4-speed with overdrive and a lockup converter, and the 4L60E and 4L80E are the electronic versions that came later: the 4L60E from the 700R4, and the 4L80E from the TH400.
| Transmission | What it is and which years |
|---|---|
| TH350 (Turbo Hydra-Matic 350) | 3-speed automatic with no overdrive, a vacuum modulator and a kickdown cable. GM used it from 1969 to the mid-1980s in cars and light pickups; the TH350C, with a lockup converter, came out around 1980 and lasted until 1986 in pickups and vans |
| TH400 (Turbo Hydra-Matic 400, later 3L80) | Bigger, heavy-duty 3-speed automatic with a vacuum modulator and an electric kickdown solenoid. It came out in 1964 and was used in work pickups and vans until 1990, at the end under the 3L80 name |
| 700R4 (later 4L60) | GM's first 4-speed automatic for rear-wheel drive, with overdrive and a lockup converter, controlled by a TV cable from the throttle and a governor. GM used it from 1982 to 1993 |
| 4L60E | The electronic version of the 700R4: the computer controls the shifts with solenoids. From 1993 in trucks and from 1994 in cars |
| 4L80E (and 4L85E) | The TH400's electronic successor, a 4-speed with overdrive for 3/4- and 1-ton trucks and vans, from 1991 |
The 700R4 has a shorter 1st gear (3.06, against 2.52 on the TH350 and 2.48 on the TH400), so it pulls harder off the line, and its overdrive 4th lowers engine speed on the highway. The 4L80E keeps the TH400's ratios and adds an overdrive 4th:
| Transmission | 1st, 2nd, 3rd and 4th gear ratios |
|---|---|
| TH350 | 2.52, 1.52 and 1.00 |
| TH400 | 2.48, 1.48 and 1.00 |
| 700R4 and 4L60E | 3.06, 1.63, 1.00 and 0.70 |
| 4L80E | 2.48, 1.48, 1.00 and 0.75 |
How do you identify your transmission by the pan?
The quickest check is to count the bolts on the pan, the oil pan under the transmission, and look at its shape. These are the counts identification guides agree on, and they're the same holes the TSS pan gaskets for each one have:
| Transmission | What its pan looks like |
|---|---|
| TH350 | 13 bolts; nearly square, with one corner cut on a diagonal |
| TH400 | 13 bolts; bigger and irregular, with several curves |
| 700R4 and 4L60E | 16 bolts; rectangular, with rounded corners |
| 4L80E and 4L85E | 17 bolts; nearly rectangular, with both corners at one end cut off |
The pan doesn't tell a 700R4 from a 4L60E: it's the same, and TSS sells the same pan gasket for both; to tell them apart, look at the cables and connectors. Some 4L60Es and 4L80Es have a deeper pan, with its own filter, but the same number of bolts. And watch out for two GM transmissions that get confused with these: according to identification guides, the 3-speed TH200 has an 11-bolt pan, and the 4-speed 200-4R, which also has a TV cable, has 16, like the 700R4.
Other clues: modulator, TV cable and connectors
- Vacuum modulator: a round metal can on the side of the transmission, with a vacuum hose from the engine. The TH350 and TH400 have one; the 700R4, 4L60E and 4L80E don't.
- Kickdown: on the TH350 it's a cable from the throttle to the transmission. On the TH400 it's electric, a solenoid inside the transmission triggered by a switch on the carburetor or the pedal, so you'll see a wire plugged into the case. The TH350C also has an electrical connector, for its lockup, but keeps the kickdown cable.
- TV cable: the 700R4 has a cable from the throttle to the transmission that, according to GM, controls line pressure, shift points, shift feel and kickdowns. It isn't just a kickdown cable, and a TH350 one won't work on it. That's why sellers in Mexico list it as a "700 de chicote" (cable 700).
- Round electrical connector: the 4L60E and 4L80E take their orders from the computer through a connector on the case, and have no modulator, TV cable or governor. In Mexico the 4L60E is known as the "700 electrónica" (electronic 700).
- Size and sensors: the 4L80E is bigger and heavier than the 4L60E, and has two speed sensors bolted into the case, one input and one output.
Where is the transmission code?
- The service parts label (RPO), usually in the glove box or the trunk, lists the vehicle's option codes: M40 is the TH400, MD8 the 700R4, M30 the 4L60E, MT1 the 4L80E and MN8 the 4L85E.
- TH350: the unit number is on the right side, at the rear, next to the pan, according to Chevrolet's 1978 light truck manual.
- TH400: a light blue plate on the right side of the transmission, according to the same manual.
- 700R4 and 4L60E: a code stamped on the right side of the case, toward the rear and above the pan (on some, at the back of the case, next to the extension housing), with the model year, the model, the day of the year it was built and the shift. For example, in the 1994 Corvette manual, "4 YK M 209 A" is a 1994 model year 4L60E built on day 209.
- 4L80E: according to industry identification guides, a riveted tag on the right side, above the pan and toward the rear; we didn't find it in a GM manual.
Best-known TH350 failures
These are the failures documented in Chevrolet's diagnosis manual, GM bulletins and the rebuild industry:
- Broken vacuum modulator: the fluid level drops with no leak in sight, and there's fluid in the vacuum hose. According to Chevrolet's diagnosis manual, if there's fluid on the vacuum side, the modulator is replaced; if there's only gasoline or water vapor, it isn't. The hose from the intake manifold is checked too.
- Slips on the 1-2 shift or burns the intermediate clutch: according to the rebuild industry, from wear in the 1-2 accumulator and its bore in the case. If it also has no engine braking in manual 2nd, the intermediate servo is checked.
- Erratic shifts, like a back-and-forth between 2nd and 3rd always at the same speed: according to the industry, it's usually a governor gear with broken teeth.
- On the TH350C, a momentary delay when shifting into Drive from loss of pump prime (the fluid level is checked first, since low fluid gives the same symptom) and a whistle in Reverse or manual 1st at idle. GM corrected them in 1981 with bulletins for the Corvette and Camaro.
Best-known TH400 failures
- Broken vacuum modulator: the same diagnosis as on the TH350, fluid in the vacuum hose or fluid loss with no visible leak.
- Very soft 1-2 and 2-3 shifts, and Reverse that's slow to engage or shudders: according to the rebuild industry, it's a common complaint on the TH400, from wear in the boost valve that raises line pressure.
- Line pressure too high that won't come down: a pressure regulator valve fault, according to the industry.
- No 3rd or no Reverse: a leak in the direct clutch drum, which works in both of those gears.
- Burnt forward clutch and seals that fail early, when the end play was set wrong during assembly.
Best-known 700R4 failures
The 700R4's classic failure is losing 3rd and 4th, or slipping in those gears, because the 3-4 clutch or the 2-4 band burns. GM addressed it in 1991 with a bulletin for 1982 to 1991 700R4 and 4L60 transmissions (91-399-7A), which says to check these first:
- The TV cable adjustment, which tells the transmission how much throttle you're giving it. GM warns never to move it to hide a shift complaint or to change performance, because that masks the cause and can damage the transmission.
- The fluid level: low fluid lowers line pressure, and the clutches burn because they don't apply fast enough or stay fully applied; too much fluid foams, and they apply with less force.
- Cooler flow: its lines can be partly blocked.
- Once it's open, the filter neck seal, the pump bushing and the check balls of the 3rd accumulator and the 3-4 clutch.
Since the 4L60E shares almost all its internal parts with the 700R4, many of its mechanical failures are the same (we explain them in the 4L60E failures guide). Other GM bulletins and the rebuild industry add these:
- Stuck in 1st with no upshift: a retaining ring out of place lets the output shaft move, and the governor gear wears (GM bulletin 91-371-7A).
- Buzz at idle, louder in Reverse: the pressure regulator valve oscillates (GM bulletin 93-29-7A).
- According to the rebuild industry, a TV system that's misadjusted or worn is the root cause of most 2-4 band and 3-4 clutch failures, and of shifts that come too early or too late.
4L60E: the electronic 700R4
The 4L60E (RPO code M30) is the electronic version of the 700R4 / 4L60: GM started using it in 1993 in trucks and in 1994 in cars. It has the same ratios and the same 16-bolt pan, but the computer controls the shifts, line pressure and converter lockup with solenoids. That's why it has no TV cable or governor, and has an electrical connector on the case. Its failures, its codes and the TSS parts that fit it are in our 4L60E guide.
Best-known 4L80E failures
The 4L80E (RPO code MT1) is the TH400's electronic successor: it uses the same 1st, 2nd and 3rd gear ratios, adds an overdrive 4th and shares parts with it such as the bands and the forward and direct friction plates. GM used it from 1991 in 3/4- and 1-ton trucks and in vans, controlled by a computer. These are its documented failures:
- On 1996 trucks with the VCM computer: slips on the 1-2 or 2-3 shift, no 3rd and 4th, or shudders on launch, sometimes with code P1870. GM traced it to a poor internal ground in the computer, which sends erratic pressure to the pressure control solenoid, and fixed it with a harness (bulletin 00-07-30-026, which also covers the 4L60E). If the fluid is already oxidized or the slip continues, the transmission needs repair.
- Harsh or delayed shifts, slipping, or no Drive or Reverse, with codes such as P0741, P0742, P0752, P0756, P0757 or P0894: GM published instructions to recondition the valve body of the 4L80E and 4L85E (bulletin 08-07-30-001).
- Uncontrolled line pressure, a buzzing noise and even broken drums or cases: according to the rebuild industry, from wear in the boost valve sleeve and the pressure regulator end plug.
- Starts in 2nd and won't upshift: a damaged filter or a leaking plug in the solenoid feed circuit, according to the industry.
- No 3rd or no Reverse: a leak in the direct clutch drum, as on the TH400.
The 4L85E (RPO code MN8) is the 4L80E version for higher-torque engines: according to GM, it mounts the same from the outside, so the way to tell them apart is the code. Its failures by symptom, codes, fluid and parts are in our 4L80E problems guide.
Which Chevrolets had these transmissions in Mexico?
Almost all the information about these transmissions online is from the United States, and in Mexico GM sold other engine and transmission combinations. This is what the General Motors de México brochures and spec sheets we found confirm:
- 1971 Impala built in Mexico: the Turbo Hydra-Matic 350 automatic is on its options list, with a console and floor shifter on the 2-door. Its base engine was the 292 six with a 3-speed manual.
- 1977 C-10 pickups and C-30 trucks: 4-speed manual only, even with the optional 350 V8.
- 1984 Monte Carlo SS: 350 V8 with a 4-speed floor-shift manual, and no automatic on its options list.
- 1997 models: the automatic Cheyenne, 400 SS, Silverado (which GM de México sold as a passenger vehicle), Suburban and Blazer have an "electronic 4-speed automatic" with 3.06, 1.63, 1.00 and 0.70 ratios, the 4L60E's. So that year's Mexican Suburban has a 4L60E, not a 4L80E. That year, the C1500, C2500 and C3500 came with a manual only.
- 1997 G-30 and Express 5.7 vans and 2003 Express 6.0: 4-speed automatic with overdrive, with no transmission name. The Express 6.0 matches the US vans that have the 4L80E, but confirm it with the code.
- The automatic 1997 Kodiak truck has an Allison transmission, not one from this family.
We didn't find Mexican spec sheets from 1978 to 1995, so we can't confirm which models from those years left the dealer with a TH350, TH400 or 700R4 in Mexico. Also, these trucks and cars are decades old, and these transmissions get swapped a lot from one vehicle to another: check the transmission, not just the model and year.
What transmission goes with the Chevrolet 350 engine?
It depends on the year and the vehicle, not the engine: the 350 V8 (5.7 liters) was used with all of these transmissions and with manuals too. In general, by era:
- From 1969 to the mid-1980s: the TH350 in cars and light pickups, and the TH400 in work trucks, vans, big cars and higher-torque engines.
- From 1980 or 1981 to 1986: the TH350C, with a lockup converter, mostly in pickups and vans; cars moved to the 700R4 earlier.
- From 1982 to 1993: the 700R4 (later called the 4L60), which GM used in the Camaro, Corvette, Caprice, C/K pickups and vans, among others.
- Until 1990: the TH400, which GM ended up calling the 3L80, stayed in C/K pickups and G work vans.
- From the 1990s: the 4L60E in half-tons and the 4L80E in 3/4- and 1-tons.
- In Mexico, several models with the 350 came with a manual: for example, the 1977 C-10 pickups and the 1984 Monte Carlo SS.
Can you put one in place of another?
Yes, and in these trucks and cars it's very common, but bolting it in isn't enough. This is what changes:
- Length, from the bellhousing face (the one that bolts to the engine) to the end of the extension housing, according to industry charts: a short-tail TH350 is about 70 cm (27 11/16 inches), a short-tail TH400 about 72 cm (28 3/8), a 700R4 or 4L60E about 78 cm (30 3/4) and a 4L80E about 83 cm (32 11/16). That's why you almost always have to move the crossmember and adjust the driveshaft.
- The output shaft: according to industry sources, the TH350's has 27 splines and the TH400's has 32, so the driveshaft yoke isn't the same.
- Kickdown: if you go from a TH350 to a TH400, the cable is replaced by an electric switch.
- Control: the 700R4 needs its TV cable properly adjusted, because, according to GM, if it binds or is misadjusted, the shift points are off and it slips. The 4L60E and 4L80E need a computer to control them.
- Strength: the TH400 and 4L80E are the heavy-duty ones; the TH350, 700R4 and 4L60E are for lighter loads.
What fluid do they take?
According to GM's manuals, the 1970s TH350 and TH400 called for Dexron or Dexron II, the 1980s 700R4 for Dexron II, and the 1990s 4L60E for Dexron III or Dexron IIE. GM kept replacing these specifications: in 1991 it said Dexron IIE could be used in all its automatics back to 1949, and in 2005, that Dexron VI could be used as a replacement where Dexron III was specified.
See TSS parts for the TH350, TH400, 700R4 and 4L80E
TSS parts for these transmissions
The TSS catalog has parts for all five (we explain the difference between the Rojo and Dorado kits in TSS Rojo vs Dorado overhaul kits):
| Transmission | TSS parts |
|---|---|
| TH350 and TH350C | TH350C Dorado (H-D) overhaul kit, filter, pan gasket, band, modulator, non-lockup bushing kit and TH350C bushing kit |
| TH400 (3L80) | pan gasket, filter, front band, reverse band, forward and direct friction plates, steel plates, washer kit and modulator |
| 700R4 (4L60) | Dorado (H-D) overhaul kit, filter, pan gasket, band, bushing kit for a 27-spline or 30-spline input shaft, washer kit, pump rotor and gears and output speed sensor |
| 4L60E | We cover them in the 4L60E guide; for example, the Dorado overhaul kit, filter and deep-pan filter |
| 4L80E and 4L85E | Dorado (H-D) overhaul kit or Dorado kit without pistons, 1997 on, filter, deep-pan filter, pan gasket, 1997-on bushing kit, pressure control solenoid, shift solenoids A and B, speed sensor, and the bands and friction plates it shares with the TH400 |
Before you order, confirm your transmission by the pan, the cables and connectors, and the code. If you're still unsure, look it up in the Transmisiones Veinte 07 transmission finder with your model and year.
Juego de Empaques TSS H-D Lock-Up TH350
Empaque de Carter Farpak TH250 TH250C TH350 TH350C MV4 M38 MX2 M31
Modulador de Presion Linea Roja / Negra TH400 TH250 TH250C TH350 TH350C
Empaque de Carter TH400 M40 3L80
Juego de Empaques TSS H-D TH700
Empaque de Carter Farpack TH700 4L60E
Juego de Empaques TSS H-D 4L80E 4L85E
Empaque de Carter 4L80E



