Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

4L80E transmission problems: stuck in 2nd, no 4th gear

TSS editorial team · · 15 min read

Technician air-testing a heavy-duty cast steel clutch drum on a transmission rebuild bench for GM 4L80E diagnosis
In short
  • The 4L80E is GM's heavy-duty 4-speed automatic (RPO code MT1), the electronic successor to the TH400. GM used it in trucks and vans over about 3,900 kg GVWR up to model year 2009; the 4L85E (MN8) is its reinforced version.
  • In Mexico, GM named it for the 2007 Express Cargo Van V8 6.0 ("4L80-E for heavy duty"); the V6 version had the 4L60E, as did the 1997 Cheyenne, Suburban and Silverado automatics.
  • In the bulletins GM published in the US, the most documented problems are fluid leaks, converter slip (P1870, which became P0894 in 2005), the valve body and shift solenoids, and gear train lubrication.
  • When the electrical side fails, the 4L80E holds 2nd, with line pressure at maximum and the converter unlocked: that's its limp mode. Each stuck solenoid leaves a different shift pattern.
  • It takes DEXRON-VI (GM approves it in place of DEXRON-III in earlier transmissions) and about 7.3 liters for a pan and filter change. In severe use, GM says to change it every 80,000 km.

The 4L80E is the 4-speed automatic General Motors used in its heavy-duty trucks and vans: HD versions of its 3/4- and 1-ton pickups, the Suburban and Yukon XL 2500, and the Express and Savana vans, among others. If yours slips, holds 2nd, won't shift into 4th or leaks fluid, here are the failures GM documented, the codes it sets, the fluid it takes and the TSS parts that fit it. If you're not sure whether yours is a 4L80E, a 4L60E or a TH400, start with our guide to identifying GM's classic transmissions.

What is the 4L80E transmission?

It's the electronic successor to the TH400: GM added a 4th overdrive gear and computer control, and started using it in 1991. The computer shifts it with two solenoids (A and B), controls line pressure with a pressure control solenoid and locks the converter with a PWM solenoid. A set of pressure switches (the switch manifold) tells it which range the lever selected, and two sensors give it input and output speed. The 4L85E is its reinforced version for higher-torque engines, and GM diagnoses it the same way.

This is how to tell it from the 4L60E, its sibling for light-duty trucks:

RPO code on the glove box labelMT1 (the 4L85E is MN8); the 4L60E is M30
Pan bolts17; the 4L60E has 16
Speed sensorsTwo bolted into the case: one input and one output
Ratios2.48, 1.48, 1.00 and 0.75, reverse 2.07; the 4L60E starts in a 3.06 first gear
Fluid for a pan and filter changeAbout 7.3 liters; the 4L60E, about 4.7
How GM describes it"Heavy duty" (GM Mexico, 2007); in the US, for trucks over 8,500 to 8,600 lb GVWR

Which vehicles have the 4L80E?

GM kept it for heavy-duty vehicles: its 1997 diagnostic files assign it to those over 8,500 lb GVWR, and its 2003 files to trucks over 8,600 lb (about 3,900 kg). That's why the same model can have a 4L60E in the light-duty version and a 4L80E in the heavy-duty one. These are the engines and vehicles GM lists with the 4L80E in the United States:

1996 to 19995.7 (HD versions), 7.4, 6.0 and 6.5 diesel engines: heavy-duty C/K pickups and utilities, G vans, P chassis and Hummer H1
2000 to 20025.7 HD, 7.4, 6.0, 8.1 and 6.5 diesel: C/K, Silverado and Sierra HD, Express and Savana, P chassis, W trucks (Isuzu NPR) and Hummer H1
2003 to 20074.8, 6.0 and 8.1: Silverado and Sierra HD, Express and Savana, Suburban and Yukon XL 2500, Avalanche 2500, P chassis and W and NPR trucks
2008 and 20094.8 and 6.0: Express, Savana, Silverado and Sierra HD. These are its last years
2010No longer used: GM's heavy-duty 6.0 trucks and vans moved to 6-speed transmissions

Two details to watch. From model year 2001, HD pickups with the Duramax diesel or the 8.1 used GM's Allison 1000, not the 4L80E. And the Hummer H2 appears with the 4L60E family in GM's 2003 to 2005 files. More models in our Chevrolet and GMC, Buick and Cadillac guides.

In Mexico, GM sold few heavy-duty automatic trucks. This is what the GM Mexico spec sheets and pages we found say:

2007 Express Cargo Van V8 6.0 (4.10 axle)"4-speed automatic transmission for heavy duty with 4L80-E overdrive"
2007 Express Cargo Van V6 4.34L60E
2007 Express 15-passenger 6.0, 2003 to 2006 Express 6.0 and model-year 2008 Cargo Van 6.04-speed automatic with overdrive, unit not named. Given the 6.0, the 4.10 axle and the weight, very probably a 4L80E
1997 G-30 cargo van 5.74-speed automatic with overdrive. Probably a 4L80E: in the US, GM used it in heavy-duty G vans with that engine
1997 Cheyenne, 400 SS, Silverado passenger SUV, Suburban and Blazer automatics4L60E (ratios 3.06, 1.63, 1.00 and 0.70)
C3500 HD, Silverado 3500 and Silverado 3500 HD (1997, 2003 and 2007)Manual
KodiakAllison automatic (1997) or Eaton manual (2003 and around 2010)
Suburban 3/4-ton 6.0 (2008 spec sheet)6-speed automatic

If your truck came used from the United States, it can have a 4L80E even if that model never had one in Mexico. Confirm it with the RPO code MT1 or MN8 on the service parts label in the glove box.

Common 4L80E problems by symptom

This table combines GM's US bulletins, its diagnostic files and the US Army's 4L80E troubleshooting manual, written for the military Humvee that used it:

Stuck in 2nd or starts in 2ndLimp mode from an electrical fault: with both shift solenoids off, the transmission holds 2nd. Also a stuck solenoid A (P0751)
No 4th (overdrive)Solenoid A or B (supply, short, ground or a leaking O-ring), the pressure switch, the computer ground, or the fourth or overrun clutch
No 3rdThe computer ground, no voltage to solenoid B or the solenoid itself (P0757), the direct clutch check ball, the intermediate sprag, the center support or the forward or direct clutch plates
No reverseLow fluid, the linkage, the reverse servo, the rear band, the direct clutch, the overdrive roller clutch, or the valve body and pressure switch
Slips in Drive or reverseLow fluid or low pressure; if only in reverse, the reverse servo seal
Slips in 4th with the converter lockedThe converter clutch or the fourth clutch (P1870 or P0894)
OverheatsLow fluid, a blocked cooler, the converter locked all the time, a stuck converter valve or pressure regulator valve, or a poorly seated pump seal
Engine stalls when put in gearLow idle, a sticking converter clutch, or a sticking forward or fourth clutch
Whine in 1st and 2ndGM published a bulletin for this noise on 1999 to 2006 units
Leaks fluidThe vent, the extension housing seal, the cooler circuit or the case (see "Fluid leaks")

Stuck in 2nd: limp mode and the solenoids

When the computer detects a serious electrical fault, it switches off the shift solenoids and the 4L80E holds 2nd, with line pressure at maximum and the converter unlocked. You can get to the shop that way, but it pulls away slowly and shifts feel harsh.

If the fault is a stuck solenoid, the transmission follows a shift pattern GM documented in its diagnostic files. For each code, these are the gears you get when the computer commands 1st, 2nd, 3rd and 4th:

P0751 (solenoid A)2-2-3-3: starts in 2nd and no 4th
P0752 (solenoid A)1-1-4-4: no 2nd or 3rd
P0756 (solenoid B)4-3-3-4: starts in 4th
P0757 (solenoid B)1-2-2-1: no 3rd

The solenoids' electrical codes are P0753 (A) and P0758 (B). Before replacing one, check its supply, the internal harness, the case connector and the computer ground. The switch manifold sets P1810 when it reports an impossible range combination, and the US Army manual lists it among the causes of no drive, no reverse or no 4th. More on these codes in our guides to shift solenoid codes and the pressure control solenoid.

Slips or overheats: the converter and code P1870 (P0894)

P1870 (1997 to 2004) and P0894 (from 2005) mean "transmission component slipping". On the 4L80E, GM sets it when there's 100 to 550 rpm of slip in the converter clutch, the fourth clutch or both, with the converter locked in 4th. So it isn't always the converter. In its US bulletins, GM fixed it in several ways:

  • With a new computer calibration, for a harsh converter lock-up with P1870 (2000 and 2001 models).
  • By reconditioning the valve body (bulletin 08-07-30-001, for harsh or delayed shifts, slipping and no Drive or reverse on 2001 to 2008 units).
  • By fixing the computer's internal ground on 1996 trucks with the VCM computer (bulletin 00-07-30-026): with a bad ground, the computer sends erratic pressure to the pressure control solenoid and the transmission slips or won't shift into 3rd and 4th.
  • And for 2006 to 2008 4L80Es and 4L85Es that slip, won't shift or overheat, with P0218 and P0894, GM published bulletin 08-07-30-016A.

The other converter codes are P0741, when it won't lock, and P0742, when it stays locked. P0218 sets with the fluid above 130 °C. For overheating, the US Army manual lists low fluid, a blocked cooler, the converter locked all the time, a stuck converter valve or pressure regulator valve and a poorly seated pump seal. Check the fluid cooler as well: GM published a US procedure to flush it and test its flow.

No 3rd or no reverse

GM published two bulletins for 4L80Es and 4L85Es that lose 3rd or reverse. 08-07-30-015 (2002 to 2008) covers code P0757 with harsh shifts, a delayed or slipping 2-3 shift, no 3rd or slipping in 3rd or reverse. 08-07-30-001 (2001 to 2008) explains how to recondition the valve body when shifts are harsh or delayed, it slips, or it won't move or has no reverse. With no codes, the US Army manual says to check the fluid level and linkage first, then the reverse servo, the rear band and the direct clutch. More causes in our guide to when reverse won't engage.

Fluid leaks

Leaks are the failure with the most GM bulletins for the 4L80E in the US:

  • From the vent (bulletin for 2002 to 2005 units). According to the US Army manual, fluid comes out there when the transmission is overfilled, or when air gets in through an internal leak at the pump cover or a poorly seated filter.
  • From the extension housing seal, on 2007 Express and Savana 2500 and 3500 and Silverado and Sierra 2500.
  • From the case and the cooler circuit: GM published how to track down leaks on 1998-and-later 4L80Es.
  • A dipstick that won't stay seated, on 2003 and 2004 Express and Savana.
  • And in 1995, GM recalled pickups and vans in the US because a thin case casting could let fluid spray onto the exhaust, with a fire risk. The fix was replacing the transmission.

A leak lowers the level, and with low fluid the transmission slips and overheats. How to find the source, in our guide to transmission fluid leaks.

Noises and internal wear

In the US, GM published a bulletin for a whine in 1st and 2nd (1999 to 2006), another with output carrier thrust washer changes (1996 to 2005) and, for 2004 models (Avalanche, Express, Savana, Sierra, Silverado, Suburban and Yukon XL, among others), a service program because the overdrive gear set could fail from lack of lubrication after a case casting change. According to the rebuilding industry, reaction carrier thrust in 1st and reverse can destroy the thrust washer, especially with a numerically low axle ratio and tall tires, and in extreme cases damage the case. More on telling noises apart in our guide to transmission noises.

4L80E trouble codes

These are the codes GM certified for the 4L80E in its 1997 to 2007 diagnostic files. Some changed numbers in 2005:

P0218Fluid overtemperature: above 130 °C for more than 10 minutes
P0502 and P0503Output (vehicle) speed sensor: no signal or sudden drops. On 1997 to 1999 6.5 diesels they're P0722 and P0723
P0706Range switch; GM published a bulletin for 2003 units that wouldn't start with this code
P0711, P0712 and P0713Fluid temperature sensor: impossible value, shorted to ground or open
P0716 and P0717Input speed sensor: the signal jumps 1,300 rpm or more, or stays below 80 rpm while the truck is moving
P0719 and P0724Brake pedal switch, the one that unlocks the converter: stuck
P0741 and P0742The converter won't lock (slips 125 rpm or more with lock-up commanded in 2nd or 3rd) or stays locked
P0751, P0752 and P0753Shift solenoid A (1-2): stuck or electrical fault
P0756, P0757 and P0758Shift solenoid B (2-3): stuck or electrical fault
P1810Pressure switch (switch manifold): reports an impossible range combination
P1860; from 2005, P2761Converter PWM solenoid: electrical fault
P1870; from 2005, P0894Component slipping: the converter clutch or the fourth clutch, with the converter locked in 4th

Two clarifications. The incorrect ratio codes (P0731 to P0734) and P0748 aren't in GM's 4L80E lists: on this transmission, a wrong ratio sets the solenoid codes (P0751 to P0757) or P1870 and P0894. And on early-nineties units, the computer set two-digit codes: for example, 81 and 82 are the 2-3 and 1-2 shift solenoids, 83 the converter solenoid, and 85 to 87 ratio errors that leave the transmission in 2nd. Look up any other code in our diagnosis by code, and the details in our guides to speed sensors, the temperature sensor and the range sensor.

Which fluid does the 4L80E take, and how much?

Early units used DEXRON-IIE and then DEXRON-III; the 2008 Express manual already calls for DEXRON-VI, and GM clarified that DEXRON-VI can replace DEXRON-III in 2005 and earlier models. Use a fluid that meets GM's specification.

  • A pan and filter change takes about 7.3 liters (7.7 quarts), according to the 2008 Express manual. The 4L60E takes about 4.7.
  • Dry, the whole transmission holds about 12.8 liters according to Jaguar, which used the same unit in its cars; each truck's cooler and lines change that figure.
  • Check it hot, at 82 to 93 °C (after about 24 km of driving), with the engine running, in Park and after moving the lever through every position.
  • Don't overfill it: GM warns the excess can come out onto hot engine parts and start a fire.

How often should 4L80E fluid be changed?

GM says to change fluid and filter every 80,000 km in severe use and every 160,000 km in normal use (2008 Express manual; the 2001 Silverado manual says 83,000 and 166,000 km). To GM, severe use means driving in traffic at 32 °C or more, hills or mountains, frequent towing, or taxi, police or delivery work; and in 2001, any truck over 8,600 lb GVWR. Given the loads, the heat and the hills, most working 4L80Es in Mexico fall under the severe schedule.

US recalls

We found no GM recalls or bulletins that name Mexico. In the US, GM ran three with this transmission:

  • 1995 (95V026): pickups and vans with a thin case casting that could let fluid spray onto the exhaust, with a fire risk. The transmission was replaced.
  • 1995 (95V139): the shift cable lock clip could back out. The lever lost its adjustment, the Park light might not come on and the truck could roll.
  • 2008 (08V313): on 2008 Express and Savana cargo and Cutaway vans with the 4.8 or 6.0, the transmission could engage 1st at highway speed. GM reprogrammed the engine and transmission computers.

If your truck came from the US, check its VIN for open recalls.

4L80E myths

  • "It was built until 2013." In GM's files, the 4L80E and 4L85E end with model year 2009; from 2010, GM's heavy-duty 6.0 trucks and vans use 6-speed transmissions.
  • "The Tahoe and the Suburban 1500 have a 4L80E." GM kept it for heavy-duty trucks; those have the 4L60E. The exception is the 6.5 diesels of the nineties.
  • "In limp mode it holds 3rd." That's said of the 4L60E. The 4L80E holds 2nd, with line pressure at maximum and the converter unlocked.
  • "P1870 or P0894 means a bad converter." On the 4L80E, the code covers the converter clutch and the fourth clutch, and GM also fixed it with calibration, the valve body and the computer ground.
  • "It takes 12.8 liters (13.5 quarts) at a fluid change." That's the dry capacity; a pan and filter change takes about 7.3.
  • "DEXRON-III only, never DEXRON-VI." GM approved DEXRON-VI in place of DEXRON-III in earlier transmissions.

How is it diagnosed?

  • Check the fluid level and condition, hot and in Park. Low fluid alone explains slipping, overheating and no reverse.
  • Read the codes with a scan tool that reaches the transmission computer and note which one set first.
  • If it's stuck in 2nd, check the case connector, the internal harness, the solenoids and the computer ground before opening the transmission.
  • Measure line pressure with a gauge. According to the US Army manual, low in every range points to the pump (worn gears, a blown-out cup plug, an internal leak or a worn bushing); high, to the pressure control solenoid, the boost or pressure regulator valves, or a bad computer ground or solenoid connection.
  • If the fluid is burnt or full of debris, the transmission most likely needs a rebuild: see what each case means in our guide to burnt fluid, debris or water.

See 4L80E parts

TSS parts for the 4L80E

The 4L80E and 4L85E page has every TSS part for this transmission. These are the ones that match the failures in this guide:

Many parts change with the year, so confirm yours with the RPO code and the year before ordering. The difference between the Rojo and Dorado kits is in our guide to TSS overhaul kits.

TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • Which vehicles have the 4L80E transmission?

    GM heavy-duty trucks and vans over about 3,900 kg GVWR, up to model year 2009: C/K, Silverado and Sierra HD pickups, Suburban and Yukon XL 2500, Express and Savana, P chassis and the Hummer H1. In Mexico, GM named it for the 2007 Express Cargo Van V8 6.0, and the 2003 to 2008 Express 6.0 very probably has it too.

  • What's the difference between the 4L60E and the 4L80E?

    The 4L80E is the heavy-duty one: RPO code MT1 (the 4L60E is M30), a 17-bolt pan (16 on the 4L60E), two speed sensors in the case, a 2.48 first gear (3.06 on the 4L60E) and about 7.3 liters at a pan and filter change (4.7). GM Mexico offered both in the same 2007 Express: the 4L60E with the V6 and the 4L80E with the V8 6.0.

  • Which fluid does the 4L80E take, and how many liters?

    DEXRON-VI, which GM approves in place of the DEXRON-III of earlier transmissions. A pan and filter change takes about 7.3 liters; the 12.8 liters you see quoted is the dry capacity. Check it hot, at 82 to 93 °C, and don't overfill it.

  • Why won't my 4L80E shift into 4th (overdrive)?

    On the electrical side: solenoid A or B, its supply or ground, the pressure switch or the computer ground; with P0751, the transmission starts in 2nd and never reaches 4th. Or internally: the fourth or overrun clutch. In 2004, GM ran a US service program because the overdrive gear set on several trucks could fail from lack of lubrication.

  • Why is my 4L80E stuck in second gear?

    That's its limp mode: when the computer switches off the shift solenoids because of a fault, the transmission holds 2nd, with line pressure at maximum and the converter unlocked. Read the codes and check the connector, harness, solenoids and grounds before opening the transmission.

  • What does code P1870 or P0894 mean on a 4L80E?

    "Transmission component slipping": 100 to 550 rpm of slip in the converter clutch or the fourth clutch, with the converter locked in 4th. It's P1870 through 2004 and P0894 from 2005. GM fixed it with calibration, valve body reconditioning or a computer ground repair; it isn't always the converter.

  • How often should 4L80E fluid be changed?

    GM says fluid and filter every 160,000 km in normal use and every 80,000 km in severe use: heat of 32 °C or more in traffic, hills, towing or delivery work. In 2001, GM counted any truck over 8,600 lb GVWR as severe use.

  • What is the 4L85E? Is it the same as the 4L80E?

    It's the reinforced version of the 4L80E (RPO code MN8), for higher-torque engines, and it appears in GM bulletins from model year 2003. GM diagnoses it with the same codes, so you tell them apart by the RPO code.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.