Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

Aisin TF-80SC/TF-81SC problems: Fusion, Mazda, Volvo

TSS editorial team · · 14 min read

Technician reviewing live pressure adaptation curves on a diagnostic tablet inside a vehicle for TF-80SC and TF-81SC
In short
  • The TF-80SC and TF-81SC are Aisin's 6-speed front-wheel-drive automatic used by Ford, Lincoln, Mazda, Volvo, Land Rover and Buick: in Mexico, the Fusion V6, Zephyr and MKZ, Mazda6 V6, CX-7 turbo, CX-9, several Volvos and the LR2.
  • Each maker has its own name for it: Ford and Land Rover call it AWF21, Mazda AW6A-EL and Volvo TF-80SC. In catalogs, the TF-80SC is the Volvo, Land Rover and GM version and the TF-81SC the Ford and Mazda one.
  • Its most documented failure is a jolt into D or R, on brake release at a stop or on the 5-4 downshift: five makers fixed it in the US with software and a relearn, and Volvo, if it stays, with internal seals.
  • Ford, Mazda, Volvo and Land Rover forbid heating the transmission by braking and revving in D for the relearn: it damages it internally.
  • It doesn't take MERCON LV: Ford calls for its "Premium" ATF or MERCON V, and Mazda for T-IV (JWS3309). On Fords it's checked hot, with a dipstick.

The TF-80SC and TF-81SC are Aisin's 6-speed front-wheel-drive automatic used by Ford, Lincoln, Mazda, Volvo, Land Rover and Buick. In Mexico it's in the Fusion V6, Zephyr and MKZ, Mazda6 V6, CX-7 turbo, CX-9 and several Volvos and Land Rovers. If yours jolts into D, on brake release or on the 5-4 downshift, here are the failures the makers documented, how the relearn is done, the codes, the test values from Ford's manual, the fluid it takes and the TSS parts. If you're not sure which transmission your vehicle has, start with our Ford and Mazda guides.

What are the TF-80SC and TF-81SC?

It's a family of Aisin 6-speed transaxles for V6 and turbo 4-cylinder engines, with front- or all-wheel drive. Each maker gave it its own name, which is why the same unit shows up as AWF21, AW6A-EL, TF-80SC or TF-81SC. This is how to identify it:

What each maker calls itFord, Lincoln and Mercury: AWF21 or "Aisin F21". Mazda: AW6A-EL (AW6AX-EL with all-wheel drive). Volvo: TF-80SC. Land Rover: AWF21. GM: "6 Speed AISIN-Warner" (RPO MDK)
TF-80SC or TF-81SCIt's a catalog convention: TF-80SC for Volvo, Land Rover and GM (AF40) and TF-81SC for Ford and Mazda (AF21 and AW6A-EL). Land Rover uses Ford's name, so go by the label
LabelAisin puts a bar-code label on the side of the case. On Fords, the transmission code on the door label is the letter B
ComputerOn the Fusion, the transmission computer (TCM) sits on top of the transmission, between the air cleaner housing and the battery, and has the range sensor built in
Ratios4.148, 2.370, 1.556, 1.155, 0.859 and 0.686; reverse 3.394 (Land Rover Mexico)
InsideA Ravigneaux gear set and a simple planetary, with clutches C1, C2 and C3 and brake B1 (Ford's manual)
Don't confuse withVolkswagen's 09G and 09M (TF-60SN and TF-61SN), the 5-speed AW55-50, Volvo's 8-speed TG-81SC and Toyota's U660E and U760E

Which vehicles have it in Mexico?

Ford Fusion 3.0 V6, 2006 to 2009The 2008 page says "transmisión automática de seis velocidades": the AWF21
Ford Fusion Sport 3.5 V6, 2010 to 2012"Transmisión automática de 6 velocidades con Selectshift" (2010 and 2011): the AWF21, which a Ford US bulletin names in the 2012 Fusion Sport
Lincoln Zephyr 2006 and MKZ 2007 to 2012The AWF21, which Ford calls "Aisin AW F21", with the 3.0 and 3.5 V6
Mazda6 3.0 V6, 2006 to 2008, and 3.7, 2009 to 2013"6 velocidades en los modelos MAZDA6 s": the AW6A-EL
Mazda CX-7 2.3 turbo, 2007 to 2012"Sport AT de 6 velocidades": the AW6A-EL (AW6AX-EL with all-wheel drive)
Mazda CX-9 V6, 2007 to 20156-speed automatic: the AW6A-EL or AW6AX-EL
Volvo S80 3.2, T6 and V8, and XC90 3.2 and V8 (2008 to 2010 pages)"Transmisión automática Geartronic de seis velocidades": the TF-80SC
Volvo XC60 T6 AWD (2010 and 2014) and S60 T6 AWD (2014)T6 AWD automatic: the TF-80SC, per Volvo's US tables
Land Rover LR2 3.2 I6 (2007 to 2010 pages)"I6 Automático", with this unit's ratios: the AWF21
Range Rover Evoque 2012 and 2013, and Buick Regal Turbo 2012 and 2013We didn't find their Mexican spec sheets; in the US they use this unit (the Evoque only in 2012 and 2013)

The makers only say "6-speed automatic"; the unit's name comes from their US documents. These aren't part of this family: the Volvo T5 2.0 (the 2013 V60 T5 is a "Powershift 6 velocidades") and the Drive-E cars from 2015 (8-speeds), the Evoque from 2014 (9-speed), the Fusion 2.3 (5-speed) and the 2010-on Fusion 2.5 and 3.0 V6, which use the 6F35, the MKZ from 2013, the Mazda6 and CX-7 2.5 (5-speeds), the CX-9 from 2016 and the Regal from 2014 (6T70). We also couldn't confirm that the 6-speed Outlander V6 belongs to this family.

TF-80SC and TF-81SC problems by symptom

Harsh engagement into D or R, or a jolt when releasing the brake at a stopComputer learning or internal leaks: Mazda, Volvo, Land Rover, GM and Ford fixed it with software and a relearn (US); if it stays, Volvo replaces internal seals
A shock on the 5-4 coast downshiftThe same. The 2011 to 2013 Volvo S80 had a recall (US): the software could skip that downshift and the engine could stall
Harsh shifts after replacing the transmission or computer, or disconnecting the batteryThe learned values were erased: it needs the relearn
Check light, P2757 and fluid between the engine and bell housing (2007 to 2010 CX-9)The converter and a leak: Mazda replaced the transmission and flushed the cooler (US)
Fails again after a repairDebris trapped in the cooler's mesh: Mazda says to flush it before installing the repaired unit
Cooler leak on the 2012 and 2013 EvoqueThe hood release cable rubbed the cooler (US)
"Transmission fault – traction reduced" on an LR2 or EvoqueNot the transmission: the all-wheel-drive coupling pump (codes P1889 or P0961 in the rear differential module)
Noise or a leak on a CX-9 AWDThe power transfer unit (PTU), with an extended warranty in the US; not the transmission
The lever won't leave P on cold mornings (CX-9)A spilled drink freezing on the interlock cable

Harsh engagement or a 5-4 shock

This is the family's best-documented failure, and five makers documented it in the US: a jolt when shifting from N, R or P to D, a jerk when releasing the brake at a stop, and a shock on the 5-4 downshift while coasting. Mazda, on the 2011 to 2013 CX-9, traced it to production variation in an internal seal ring that kept the computer from learning pressure correctly, and fixed it by reprogramming the computer and running the learning procedure; some computers couldn't be reprogrammed and had to be replaced.

Volvo, on its 2011 to 2018 models (S60, S80, V60, XC60, XC70 and XC90), speaks of "internal tolerance deviation" in the TF-80SC: first, software and adaptation in five temperature bands, from 40 to 110 °C; if the jolt stays, an internal seal kit. In another bulletin, Volvo writes: "Do not replace the gearbox." Land Rover (2011 to 2015 LR2 and 2012 and 2013 Evoque) and GM (2011 to 2013 Regal) also fixed it with software, and Ford released computer updates for the 2006 and 2007 Fusion, Milan and Zephyr with the 3.0 V6.

These are US bulletins; we found none for Mexico, so ask your dealer whether there's an update for your VIN. The makers reach the same conclusion: first the software and the learning procedure, at the right temperature; seals and pistons if the jolt stays; and don't condemn the transmission for this alone.

The relearn, without heating the transmission on the brake

Ford calls for the initial learn with a new transmission or a new or reprogrammed computer, and replacement linear solenoids need it too. Ford, Mazda, Volvo and Land Rover all forbid the same thing: heating the fluid by braking and revving in D, because it damages the transmission internally. This is how Ford's 2010 Fusion service manual describes it:

  • With the fluid at 66 to 110 °C and your foot on the brake, shift from N to D and wait 3 seconds, 5 times; then from N to R, 5 more times.
  • Then drive 10 times at 20 to 25 % throttle up to 6th, no faster than 80 km/h (50 mph), and let the car coast to a stop in under 60 seconds.
  • Ford warns that a new or freshly relearned unit may shift harshly for the first few hundred miles, and that disconnecting the battery for 20 minutes erases the learned pressures.

Mazda runs a similar procedure (N to D and N to R, 5 times each); Volvo repeats it at least 10 times in each temperature band, and Land Rover warns that shift quality can take several weeks to settle.

Converter, P2757 and leaks

On the 2007 to 2010 US CX-9, Mazda documented code P2757 together with a fluid leak between the engine and the bell housing. With that code, the transmission goes into limp mode, limits converter control and may jolt; Mazda replaced the transmission, power-flushed the cooler and only replaced the computer if the code came back.

Before replacing the converter, Ford says to check the codes, pressure and stall test "to prevent the unnecessary installation of new or remanufactured torque converters". The converter clutch won't apply with the fluid below 0 °C. If there's fluid at the bottom of the bell housing, it can come from five places, and Ford uses UV dye to find the leak before removing the transmission. On the 2010 to 2012 Fusion, Milan and MKZ, Ford also says to grease the converter pilot hub and check the dowels when installing the transmission, or the flexplate can crack (US).

Mazda stresses the cooler: the most common cause of a repaired transmission failing again is a lack of lubrication to the planetaries from debris trapped in the cooler's mesh, and it says to power-flush it before installing the transmission. If coolant got into the fluid (it looks pink and foamy), Ford replaces the transmission if it can't be taken apart and cleaned, and flushes the cooler and lines. More in our cooler and fluid leaks guides.

Trouble codes

These are the codes the makers tie to this transmission in their bulletins:

P2757Mazda: converter clutch control solenoid circuit, performance or stuck off (CX-9)
P0895By the standard, "shift time too short". Volvo lists it with the 5-4 shock and the N to D jolt, and warns it may not be stored even with symptoms
P2544By the standard, the torque management request input signal. A Ford US bulletin ties it to harsh or erratic shifts with the wrench light on (2005 Five Hundred)
P0562System voltage low: Ford documented limp mode with this code after a jump start (2005 Five Hundred)
P1889 and P0961 (rear differential module)Land Rover LR2 and Evoque: the "Transmission fault – traction reduced" message comes from the all-wheel-drive coupling, not the transmission
P176B2012 to 2014 Evoque: rotary shifter control error

The code chart in Ford's manual for this unit runs from P0562 to P2764, plus U0073 and U0100, and each code carries two more characters for the failure type. More in our guides to TCM voltage, lost communication and the transmission control module, or in our diagnosis by code.

Limp mode

According to Ford's service manual, when a solenoid fails the computer cuts its current and line pressure goes to maximum, so expect hard engagements; if all the shift solenoids fail, the transmission moves on its hydraulic circuits alone, so you can drive a short distance. With P2757, Mazda says the transmission goes into limp mode, limits converter control and may jolt. We couldn't read which gear it holds: that table in Ford's manual is an image that wasn't preserved.

Test values from Ford's manual

These come from Ford's 2010 Fusion 3.5 V6 service manual, where the unit is called "Aisin AW21":

SSA and SSB shift solenoids (on/off)11 to 15 Ω
SSC, SSD, SSE and SSF linear solenoids, line pressure (PCA) and converter clutch (TCC)5.0 to 5.6 Ω
Insulation to groundMore than 10,000 Ω
Harness continuityLess than 5 Ω
Converter clutch testFluid at 43 to 47 °C, at 35–60 km/h (22–37 mph); it won't apply below 0 °C
Stall testWide-open throttle no more than 5 seconds in R, D and L, with 15 seconds in N at 1,000 rpm between tests
Drain and fill plugs47 N·m and 39 N·m

If the resistances are fine and the code stays, Ford replaces and reprograms the computer; if a solenoid is out of range or the harness is open, it replaces the main control valve body or the internal harness, and with pressure out of spec, the valve body. Ford doesn't list the solenoids separately; TSS does carry them, and its linear solenoid set needs a relearn. More in our solenoid and valve body guides.

Which fluid does it take, and how is it checked?

It depends on the maker. Mazda calls for T-IV type ATF (JWS3309) and warns that a generic or universal ATF can damage the transmission. Ford specified its "Premium" ATF (spec WSS-M2C924-A) and, since February 2024, authorizes MERCON V for top-offs and complete refills, saying mixing them is acceptable. It isn't MERCON LV, which is the 6F35's fluid. For Volvo, Land Rover and Buick, check your owner's manual.

The Fusion, Zephyr and MKZ have a dipstick. This is how Ford checks it:

  • Drive about 30 km (20 miles) until the fluid reaches 60–70 °C, park on level ground and, with the engine idling and your foot on the brake, move the lever through every position.
  • With the engine idling, check the dipstick; the cold mark is only valid with the fluid at 15–25 °C.
  • If it's low, add 0.25 L at a time through the fill plug on top of the transmission, without overfilling: too much causes erratic pressure, foaming and fluid out the vent; too little, slow engagement and slipping.

Approximate capacity is 7.0 liters (7.4 qt) dry and about 3.7 liters (3.9 qt) for a drain and refill. Ford says not to use additives.

How often should the fluid be changed?

In Ford's 2011 maintenance schedule, the fluid is changed every 240,000 km (150,000 miles) in normal use and every 48,000 km (30,000 miles) if the vehicle spends a lot of time idling or at low speed, or on dusty roads; Ford notes this unit needs no filter change at service. It isn't "sealed for life". For Mazda, Volvo and Land Rover, follow your manual's schedule.

TF-80SC and TF-81SC myths

  • "If it jolts into D, the transmission is shot." Five makers fixed it with software and a relearn, and Volvo writes: "Do not replace the gearbox."
  • "For the relearn, heat the transmission by braking and revving in D." Ford, Mazda, Volvo and Land Rover forbid it: it damages the transmission internally.
  • "It takes MERCON LV, like newer Fords." No: Ford calls for its "Premium" ATF or MERCON V, and Mazda for T-IV (JWS3309).
  • "It's sealed for life." Ford schedules fluid changes: every 240,000 km, or every 48,000 km in severe use.
  • "With P2757, replace the converter solenoid." On the CX-9, Mazda found it together with a bell-housing leak and replaced the transmission.
  • "On an LR2 or Evoque, 'Transmission fault – traction reduced' means the transmission." Land Rover ties it to the all-wheel-drive coupling pump.
  • "Every Volvo T5 and every Evoque has the TF-80SC." The 2013 V60 T5 is a Powershift, the Drive-E cars are 8-speeds, and the Evoque only had this unit in 2012 and 2013.
  • "The 2010 to 2012 Fusion has the Aisin." Only the Fusion Sport 3.5 V6; that era's 2.5 and 3.0 V6 use the 6F35.

How is it diagnosed?

  • Read the codes from the transmission computer and, if it has one, the all-wheel-drive module.
  • Check the fluid level and condition: dark red is fine; brown, black, burnt-smelling, or pink and foamy (coolant) is not.
  • If the jolt comes into D or R, on brake release or on the 5-4 downshift, ask the dealer about software updates and run the relearn at the right temperature, without heating the transmission on the brake.
  • Measure the solenoids against Ford's values: 11 to 15 Ω for the on/off ones and 5.0 to 5.6 Ω for the linear ones.
  • Run the pressure and stall tests before condemning the converter or the transmission.
  • If you're rebuilding or replacing the transmission, power-flush the cooler and its lines.
  • After replacing the transmission, computer, valve body or linear solenoids, run the relearn.

See TF-80SC and TF-81SC parts

TSS parts for the TF-80SC and TF-81SC

The TF-80SC and TF-81SC page has every TSS part for this family. These are the ones that match the jobs in this guide:

Jolts that stay after the software and relearn (internal seals)TF-80SC Rojo overhaul kit and 4-piston kit for the TF-80SC and TF-81SC
Burnt clutches or slippingFriction packs for the TF-81SC (Ford and Mazda) or TF-80SC (Volvo), C2 4th-5th-6th plate and C1 plate
Solenoids out of range6 linear solenoid set for the TF-81SC, which needs a relearn, and A-B shift solenoid
Repairs with the transmission openFilter and lubricated pump bushing
Axle seal leaksTF-80SC axle seal

We didn't find a converter or valve body for these units in the TSS catalog, and the combo overhaul kit for both versions is out of stock. Confirm with your distributor whether your unit is a TF-80SC or TF-81SC, because the friction packs and linear solenoids differ, and that the filter and seal fit. The difference between the Rojo and Dorado kits is in our guide to TSS overhaul kits.

TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • Which vehicles have the TF-80SC or TF-81SC in Mexico?

    Per the makers' pages: Ford Fusion 3.0 V6 (2006 to 2009) and Fusion Sport 3.5 V6 (2010 to 2012), Lincoln Zephyr 2006 and MKZ 2007 to 2012, Mazda6 V6 (2006 to 2013), CX-7 2.3 turbo (2007 to 2012) and CX-9 V6 (2007 to 2015), Volvo S80 and XC90 3.2, T6 and V8, XC60 and S60 T6 AWD, and the Land Rover LR2 I6. Ford and Land Rover call it AWF21, Mazda AW6A-EL and Volvo TF-80SC.

  • What's the difference between the TF-80SC and TF-81SC?

    They're the same Aisin 6-speed family, with the same ratios. In catalogs, the TF-80SC is the Volvo, Land Rover and GM version and the TF-81SC the Ford and Mazda one. In the TSS catalog, the filter, pistons, pump bushing and C1 and C2 plates fit both; the friction packs and linear solenoids differ. Check your transmission's label.

  • Why does it jolt into D or on the 5-4 downshift?

    It's the most documented failure: Mazda, Volvo, Land Rover, GM and Ford fixed it in the US by updating the computer and running a relearn. Mazda traced it to variation in an internal seal ring and Volvo to internal tolerances; if the jolt stays, Volvo replaces internal seals. Ask your dealer whether there's an update for your vehicle.

  • Which fluid do the TF-80SC and TF-81SC take?

    Mazda calls for T-IV type ATF (JWS3309). Ford specified its "Premium" ATF (spec WSS-M2C924-A) and since 2024 authorizes MERCON V. It isn't MERCON LV or a universal ATF. For Volvo and Land Rover, check your owner's manual.

  • How do you check the level on a Fusion or MKZ?

    With the dipstick: fluid at 60–70 °C after about 30 km (20 miles), the car on level ground, the engine idling and after moving the lever through every position. Add 0.25 L at a time, without overfilling. The cold mark is only valid with the fluid at 15–25 °C.

  • What does code P2757 mean on a CX-9?

    To Mazda, a converter solenoid circuit performance fault, or the solenoid stuck off. On the 2007 to 2010 US CX-9 it came with a leak between the engine and bell housing: the transmission goes into limp mode, and Mazda replaced the transmission and flushed the cooler.

  • Do you need a relearn after replacing solenoids, the valve body or the computer?

    Yes. Ford calls for the initial learn with a new transmission or a new or reprogrammed computer, with the fluid at 66 to 110 °C, and forbids heating it by braking and revving in D. Replacement linear solenoids need it too.

  • My LR2 or Evoque says "Transmission fault – traction reduced": is it the transmission?

    Not necessarily: Land Rover ties it to codes P1889 and P0961 in the rear differential module, from the all-wheel-drive coupling pump.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.