Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

6F50 & 6T70 problems: Edge, Explorer, Traverse, Acadia

TSS editorial team · · 16 min read

Technical 3D cutaway of a 6-speed transverse automatic transaxle illustrating internal clutches for Ford 6F50 and GM 6T70
In short
  • Ford and GM designed this 6-speed together: Ford calls it the 6F50 and 6F55, and GM the 6T70 and 6T75. They share about 85 % of the mechanical parts and the same ratios, but not the computer or the fluid.
  • In Mexico it's in the Edge and Explorer V6 and several Lincolns (Ford), and the Traverse, Acadia, Enclave, Malibu V6 and Captiva Sport 3.6 (GM).
  • Its most documented failure is the 3-5-reverse clutch, which Ford calls the direct clutch: the transmission loses reverse, 3rd and 5th, with code P0776 on GM or P0756 on Ford.
  • In limp mode it holds 5th: Ford leaves only P, R, N and 5th when the speed sensors fail, and GM holds 3rd or 5th with an electrical fault.
  • Both have a dipstick and are checked at 82 to 93 °C. GM takes DEXRON-VI and Ford MERCON LV from 2010; in severe use, GM calls for a fluid change every 80,000 km.

Ford's 6F50 and GM's 6T70 are the same 6-speed automatic, designed by both makers together. In Mexico it's in the Edge and Explorer V6 and several Lincolns, and the Traverse, Acadia, Enclave, Malibu V6 and Captiva Sport 3.6. If yours has lost reverse, 3rd and 5th, is stuck in 5th, slips or bangs, here are the failures Ford and GM documented, each maker's codes, the test values, the fluid it takes and the TSS parts that fit it. If you're not sure which transmission your vehicle has, see our Ford and GMC, Buick and Cadillac guides.

What are the 6F50 and 6T70?

According to a technical paper by GM and Ford engineers, the two makers developed this front-wheel-drive transmission together: Ford's 6F50 matches GM's 6T70, and the 6F55 the 6T75, the higher-capacity versions. They share about 85 % of the mechanical parts and the same six ratios, and they debuted in 2007 in the Edge, MKX and Saturn Aura. GM built them in Warren, Michigan, and in Ramos Arizpe, Coahuila.

The difference is the control system. On GM's, the transmission computer, solenoids, pressure switches and temperature sensor form a single part inside the transmission (GM calls it the TEHCM and doesn't sell its pieces separately). On Ford's, the engine computer runs an internal solenoid body; if it's replaced, its ID code and strategy have to be loaded into the computer. This is how to tell them apart:

Ratios (both makers)4.48, 2.87, 1.84, 1.41, 1.00 and 0.74; reverse 2.88
Higher-capacity versionsGM's 6T75 and Ford's 6F55; according to their engineers, only the transfer shafts and case housings change
ComputerGM: inside the transmission, with the solenoids and pressure switches (the TEHCM). Ford: the engine computer runs an internal solenoid body
ID codesGM: RPO MH2 and MH4 (6T70), MY9 and MH6 (6T75); from 2013, M7U to M7X. Ford: a letter on the door-pillar label, which varies by model (on the 2012 Edge, J is the 6F50)
FluidGM: DEXRON-VI. Ford: MERCON V from 2007 to 2009 and MERCON LV from 2010
DipstickBoth have one; the level is checked hot, at 82 to 93 °C. The smaller 6F35 has none
3-5-reverse clutch codeGM: P0776. Ford calls it the direct clutch: P0756

Which vehicles have it in Mexico?

These are the applications we found on Ford and GM Mexico pages; where the spec sheet isn't enough, we say so:

Ford Edge 3.5 V6, 2007 to 20166F50 ("automática de 6 velocidades con SelectShift")
Ford Edge Sport 2.7 EcoBoost, 2016 onProbably the 6F55; the 2018-on Edge 2.0 uses the 6F35
Ford Explorer 3.5 V6, 2012 to 20176F50
Ford Explorer Sport 3.5 EcoBoost, 2015 to 2017Probably the 6F55
Lincoln MKX, 2007 to 20156F50
Lincoln MKS 3.7 and 3.5 EcoBoost6F50 with the 3.7 and 6F55 with the EcoBoost
Lincoln MKZ 3.7 (2013 to 2016); MKZ 3.0 and Continental (2017 on)6F50; 6F55
Chevrolet Traverse, 2009 to 20176T75
GMC Acadia, 2008 to 20166T75
GMC Acadia, 2017 to 2019Second-generation 6T70
Buick Enclave, 2010 to 20176T75
Chevrolet Malibu 3.6 (2008 to 2012) and 2.0 turbo (2013 to 2015)6T70
Chevrolet Captiva Sport 3.6, 2008 to 20106T70
Buick LaCrosse 3.6, 2014 to 2016 Regal 2.0 turbo, GMC Terrain V6 and Cadillac SRX6T70, per GM's US applications

These aren't part of this family: the Equinox (not sold from 2009 to 2015, and later with the 6T45 or 6T40), the 2018-on Edge 2.0 and the US 4-cylinder Explorers (6F35), the 2010 to 2012 MKZ 3.5 (Aisin), and the Flex, Taurus and MKT, which weren't sold new in Mexico. The 2011-on Captiva Sport 2.4 and 3.0 uses GM's smaller family: see our 6T40 and Captiva guides.

6F50 and 6T70 problems by symptom

This table combines the bulletins Ford and GM published in the US and their service manuals:

No reverse, 3rd or 5th, or slipping on those shifts, with P0776 (GM) or P0756 (Ford)The 3-5-reverse clutch, which Ford calls the direct clutch: a broken wave plate (GM 2007 to 2009), the input sensor ring out of its groove (GM 2016) or a pushed-out snap ring (Ford 2015 and 2016)
Stuck in 5th, very slow takeoffLimp mode: on Ford, from a speed sensor fault (only P, R, N and 5th remain); on GM, from an electrical fault
Launch shudder, harsh 2-3 or 3-2 shifts, flares or slipping (GM 2014 to 2018)Debris or wear in both valve bodies; GM replaces them and warns that replacing the module doesn't fix it
Shudder or engine stall when stopping, with P0742 (GM 2013)The converter solenoid, inside the module, stuck by debris
Starts in 4th or hesitates, no codes (Ford 2010)A sticking multiplex shift valve
Harsh 1-2 shift, no codes (2015 to 2017 Traverse, Acadia and Enclave)The 2-6 clutch needs to relearn: GM calls for a learn drive before replacing parts
Drops to neutral, starts in 5th or the backup camera comes on in D (Ford 2009 to 2011)The digital range sensor, with high resistance
OverheatsGM warns on the dash from 132 °C, and Ford sets P1783 above 135 °C: fluid level, cooler and converter
Leaks between the engine and transmissionFord: the converter hub seal (only the seal is replaced); GM: a poorly cast converter housing on the 2013 SRX
Smells like gas, clunks or knocks underneath on an AWD versionOften it's the power transfer unit (PTU), which is separate and has its own oil

No reverse, 3rd or 5th: the 3-5-reverse clutch

This is the family's most documented failure. The 3-5-reverse clutch, which Ford calls the direct clutch, works in 3rd, 5th and reverse, so when it fails exactly those three are lost. On its 2007 to 2009 units, GM documented a wave plate that breaks and lets the piston over-stroke, with code P0776. Its pieces can damage the speed sensors and other clutches, so GM says to open the transmission, clean it and replace the pump filter and the solenoid filter plate, along with the plate; the converter is replaced only if the filters show debris.

The failure didn't stay in those years. In 2016, GM found transmissions without reverse or 3rd because the input sensor's retaining ring came out of its groove, and it replaced the ring, the 3-5-reverse piston and its housing. Ford documented, on units built between November 2015 and February 2016, a sensor wheel that pushed the direct clutch snap ring out until it damaged the hub, with codes P0715, P0717, P0756 and P2701.

In the US, GM ran a special coverage program of up to 10 years for the wave plate on 2007 to 2009 models; it has ended and didn't cover vehicles sold in Mexico. More on the code in our P0776 and P0796 guide.

Stuck in 5th: limp mode

Both makers protect the transmission by leaving it in a high gear. This is what their service manuals say:

GM, electrical fault in 1st, 2nd or 3rdHolds 3rd
GM, electrical fault in 4th, 5th or 6thHolds 5th until the engine is shut off or reverse is selected; then 3rd
GM, P0776 (3-5-reverse clutch)Allows only reverse, 2nd and 4th
GM, P0716 or P0717 (input sensor)Line pressure at maximum, no converter lock-up, and only reverse and 5th
Ford, speed sensor fault (P0715, P0717, P0720 or P0722)Cuts power to every solenoid: only P, R, N and 5th, with pressure at maximum and the converter unlocked
Ford, P0756 (direct clutch)Disables 3rd and 5th

That's why a vehicle that pulls away very slowly and won't shift is almost always in limp mode, not "missing first". Read the codes before replacing parts. More on the sensors in our speed sensor guide.

Valve body, module and solenoid body

On second-generation 6T70s and 6T75s (2014 to 2018), GM documented launch and 4th-gear shudder, harsh 2-3 and 3-2 shifts, flares and slipping from debris or wear in both valve bodies, and stated that replacing the module had not been an effective repair. On 2013 units, the converter solenoid inside the module stuck from debris: the engine could stall when stopping, with P0742. GM reflashed units in dealer stock and, on customer vehicles, replaced the module. It also warned that P0965 on 2013 6T70s and 6T75s can set falsely near 0 °C.

On Ford, US bulletins cover a separator plate that leaked through a shallow bolt pocket (2013), a sticking multiplex shift valve that made it start in 4th (2010) and a wrong separator plate in overhaul kits (2010 to 2012). According to the rebuilding industry, some GM modules built between July and September 2017 have a capacitor that causes intermittent P0776, P0796, P0965 and P0969. More in our valve body and transmission control module guides.

Speed and range sensors

On Ford, an intermittent short in the output and turbine sensors of units built before 2007 caused harsh engagements, no shifts or 5th only. On 2009 to 2011 units, a high-resistance digital range sensor made the transmission drop to neutral or start in 5th, turned on the backup camera in D or switched off cruise control; Ford measures it at the transmission connector and replaces it above 5 Ω. On GM, a 2007 and 2008 bulletin replaced the speed sensor with several solenoid and ratio codes. More in our range sensor guide.

Overheating, converter and leaks

GM turns on its hot-transmission warning when the fluid passes 132 °C for 5 seconds, and Ford sets P1783 above 135 °C. Check the level (overfilling also overheats it), the cooler and the converter. Ford documented converters with a torn inner seal, with only P0741 and P1744, and leaks at the converter hub seal fixed by replacing just the seal. On GM, the 2013 SRX had poorly cast converter housings. How to find a leak, in our fluid leaks guide.

The power transfer unit (PTU) isn't the transmission

On AWD versions, the power transfer unit (PTU) bolts to the transmission, but it's separate and has its own gear oil: on the Edge, just 0.35 liters. Ford documented in the US that heat breaks that oil down and leaves a gas-like smell, and knocking noises fixed with a PTU kit; GM, oil leaking from its PTU vent. If your AWD vehicle smells or knocks underneath, check the PTU before blaming the transmission.

6F50 and 6T70 trouble codes

Each maker uses its own codes for the same clutch. In the table, "GM" is the 6T70 and 6T75 and "Ford" the 6F50 and 6F55:

P0776 and P0777 (GM)Solenoid 2, for the 3-5-reverse clutch: the clutch slips or stays applied
P0756, P0733 and P0735 (Ford)Direct clutch (3-5-reverse) fault: flares into 3rd or 5th
P0796 and P0797 (GM)Solenoid 3, for the 4-5-6 clutch and the low and reverse clutch
P0729, P0734 and P0766 (Ford)Solenoid D stuck off: no 4th, 5th or 6th, and delayed or no reverse
P0716 and P0717 (GM); P0715 and P0717 (Ford)Input speed sensor
P0720 and P0722 (Ford)Output speed sensor
P0741 and P0742 (GM); P0741 and P1744 (Ford)The converter won't lock or stays locked; Ford notes that P0741 and P1744 mean the same thing
P0842 and P0843 (GM)Pressure switch 1, inside the module; no check engine light
P0965 (GM)Solenoid 2 current doesn't match the command; no check engine light, and GM warns it can be false on cold days
P1783 (Ford)Fluid above 135 °C for 5 seconds
P182E and P1915 (GM)Internal range sensor: impossible range, or not in P or N at start
P0711 to P0713Fluid temperature sensor

Look up any other code in our diagnosis by code, and the temperature sensor codes in our P0711 to P0713 guide.

Test values

Ford publishes its unit's values in the 2011 Edge service manual; GM doesn't, because its solenoids sit inside the module:

SSA, SSB, SSC, SSD, converter and line pressure solenoids (Ford)4.00 to 5.89 Ω, at 20 to 30 °C
SSE on/off solenoid (Ford)19.05 to 27.95 Ω, at 20 to 30 °C
Fluid temperature sensor (Ford)104 to 35 kΩ at 0 to 20 °C, and 5.6 to 2.5 kΩ at 71 to 90 °C
Line pressure at idle (Ford)D: 579 to 600 kPa. R: 689 to 724 kPa
Line pressure at stall (Ford)D: 1,655 to 1,724 kPa. R: 1,724 to 2,068 kPa
Stall speed (Ford, 3.5 and 3.7 engines)2,350 to 2,650 rpm, for no more than 5 seconds
Digital range sensor (Ford)More than 5 Ω between its pins means a bad sensor
Solenoids and temperature sensor (GM)GM publishes no values: they sit inside the module and are tested with a scan tool

On GM, line pressure is tested with a gauge while the scan tool commands pressure in P or N: at maximum it should read 1,860 to 2,070 kPa.

Which fluid does it take, and how much?

  • GM (6T70 and 6T75): DEXRON-VI. It holds about 9.0 liters in total; a pan drain gives 4 to 6.
  • Ford (6F50 and 6F55): MERCON V from 2007 to 2009 and MERCON LV from 2010. About 10.4 liters dry; about 4.3 go back in after removing the main control cover.
  • Check the level hot, with the fluid at 82 to 93 °C, at idle and after moving the lever through every position; both have a dipstick. On the 6F50, the dipstick is in the main control cover, and on Ford EcoBoost models the air filter box has to be moved.
  • Don't overfill it: Ford warns that excess fluid overheats the transmission.

How often should the fluid be changed?

In its US manuals, GM calls for a change every 160,000 km in normal use and every 80,000 km in severe use: traffic in hot weather, hills or mountains, towing, taxi, police or delivery work. Ford calls for every 48,000 km under special conditions, such as towing or long idling. Given Mexico's heat and traffic, the severe schedule is the prudent choice. After a repair, GM requires the adaptive values learn, and Ford notes that shifts can feel abrupt for the first few hundred kilometers while the computer learns.

US recalls and programs

We found no recalls or programs that apply in Mexico. In the US:

  • GM Special Coverage 14404: up to 10 years for the wave plate failure on 2007 to 2009 Acadia, Enclave, Traverse, Malibu, Equinox, Vue, Aura, G6 and others. It was US-only and has ended.
  • 08V200: 26 2008 Saturn Vues with the 6T70 and a porous case next to the parking pawl; the transmission was replaced.
  • 09V073, 11V595 and 14V092: the shift cable on several GM models with this transmission (Acadia, Enclave, Traverse, Malibu and SRX, among others).
  • 14V212: the 2013 SRX 3.6 could take 3 or 4 seconds to accelerate because of its transmission computer programming.
  • 14V393 (Ford) and 17V516 (GM): halfshafts on 2012 to 2014 Edge, MKX and others, and the right intermediate shaft on the 2017 and 2018 Acadia.

If your vehicle came from the US, check its VIN for open recalls.

6F50 and 6T70 myths

  • "The 6F50 and 6T70 are identical; everything interchanges." They share the design and about 85 % of the mechanical parts, but not the computer, solenoid body or calibration.
  • "The wave plate was fixed in 2010." GM documented another 3-5-reverse failure in 2016, and Ford on its 2015 and 2016 units.
  • "There's an extended warranty for your Traverse or Acadia." GM's program was US-only, for 2007 to 2009 models, and it has ended.
  • "With P0776 you have to replace the module." GM says not to replace the module unless its diagnosis calls for it, and for 2014 to 2018 models it stated that replacing it doesn't fix shudder.
  • "The 6F50 has no dipstick." Both do; the one without is the 6F35, the family's smaller unit.
  • "The fluid is lifetime." GM and Ford both publish fluid changes; in severe use, GM calls for every 80,000 km.
  • "If it smells like gas or clunks underneath, it's the transmission." On AWD versions it's often the power transfer unit (PTU), which has its own oil.
  • "The Edge 2.0 and Explorer 2.3 have the 6F50." Those use the 6F35; and in Mexico the 2012 to 2017 Explorer was only sold with a V6.

How is it diagnosed?

  • Check the level with the dipstick, hot, and the fluid's condition.
  • Read the codes with a scan tool that reaches the transmission computer: on GM, the transmission module; on Ford, the engine computer. Note which code set first.
  • No reverse, 3rd or 5th with P0776 or P0756: think 3-5-reverse clutch first. If you open the transmission, on GM also replace the pump filter and the solenoid filter plate.
  • If it's stuck in 5th, check the speed sensors and their harness before the hydraulic side; on Ford, also the range sensor.
  • With harsh shifts or slipping, measure line pressure (on Ford, against the values in the table).
  • On an AWD version with smells or noises underneath, check the power transfer unit before blaming the transmission.
  • After the repair: on GM, the adaptive values learn; on Ford, load the solenoid body code into the computer if it was replaced.

See 6F50 and 6T70 parts

TSS parts for the 6F50 and 6T70

The 6F50, 6F55, 6T70 and 6T75 page has every TSS part for this family. These are the ones that match the failures in this guide:

After a 3-5-reverse failure (debris in the transmission)Pump filter and solenoid screen filter
3-5-reverse clutch and other clutch repairs5-piston kit and steel plate pack
Speed sensors (Ford): P0715, P0717, P0720 and P0722Input sensor and output sensor
Full rebuild (GM)6T70 and 6T75 Rojo overhaul kit, or Dorado without pistons for the 1st generation or the 2nd generation
Full rebuild (Ford)6F50 and 6F55 Rojo overhaul kit
Pressure switches in GM's 1st-generation module (P0842, P0843)Diaphragms to repair the module
Leak at the shift shaftShift shaft seal

TSS doesn't carry GM's module, Ford's solenoid body or the wave plate on its own. Confirm the generation with your distributor (on GM, the 2nd starts in 2013) and whether the part is for the Ford or the GM version. The difference between the Rojo and Dorado kits is in our guide to TSS overhaul kits.

TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • Are Ford's 6F50 and GM's 6T70 the same transmission?

    Nearly: Ford and GM designed it together, they share about 85 % of the mechanical parts and have the same six ratios. What changes is the control (GM puts the module inside the transmission; Ford runs it from the engine computer with a solenoid body that has to be programmed), the fluid and the calibration.

  • How do the 6T70 and 6T75, or the 6F50 and 6F55, differ?

    The 6T75 and 6F55 are the higher-capacity versions; according to GM and Ford engineers, only the transfer shafts and case housings change. In Mexico, the Traverse, the 2008 to 2016 Acadia and the Enclave use the 6T75, and the Explorer Sport and MKZ 3.0 the 6F55.

  • My Traverse has no reverse or 3rd and sets P0776. What is it?

    In the US, GM documented that on 2007 to 2009 6T70s and 6T75s the 3-5-reverse clutch wave plate breaks, and its pieces damage the sensors and other clutches: it says to open the transmission, clean it and replace the pump and solenoid filters. In 2016 there was another cause, the input sensor's ring.

  • Is there an extended warranty for the wave plate failure?

    GM ran a US program (14404) for 2007 to 2009 models, valid up to 10 years from sale; it has ended and didn't cover vehicles sold in Mexico.

  • Which fluid does the 6F50 or 6T70 take?

    The 6T70 and 6T75, DEXRON-VI. The 6F50 and 6F55, MERCON V from 2007 to 2009 and MERCON LV from 2010. Check the level hot, at 82 to 93 °C, with the dipstick.

  • How often should the fluid be changed?

    In its US manuals, GM calls for every 160,000 km in normal use and every 80,000 km in severe use (traffic in heat, mountains, towing); Ford, every 48,000 km under special conditions. In Mexico, severe use is the norm.

  • Why is my Edge or Explorer stuck in fifth and slow to pull away?

    That's limp mode: with speed sensor faults, Ford leaves only P, R, N and fifth with pressure at maximum; GM holds 3rd or 5th with an electrical fault. Read the codes before replacing parts.

  • My AWD Edge smells like gas or knocks underneath. Is it the transmission?

    Often it's the power transfer unit (PTU), which is separate and has its own gear oil. Ford documented in the US that heat breaks it down, leaving a gas smell, and knocking noises.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.