Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

GM 5L40E and 5L50E problems: Cadillac CTS, SRX, STS

TSS editorial team · · 10 min read

Interior center console automatic gear selector detail representing GM 5L40E and 5L50E vehicles
In short
  • The 5L40E and 5L50E are the 5-speed automatic GM built in France: the 5L50E with the Northstar V8 and the 5L40E with the V6s. The first ones went to BMW.
  • In Mexico they're in the 2003 to 2007 Cadillac CTS, the 2004 to 2007 SRX, the 2005 to 2007 STS and the 2004 to 2006 XLR; the Mexican Pontiac Solstice was a manual.
  • Its limp mode is 5th, or 4th, not 3rd: maximum pressure, no converter lockup and the lever has no effect on the forward gears.
  • In the US, GM fixed light-load shudder by reprogramming the computer, and says P0742 is almost never the converter.
  • It has no dipstick: the level is checked at the plug with the engine running. GM calls for DEXRON-VI instead of the original DEXRON-III.

The 5L40E and 5L50E are the 5-speed automatic in 2000s Cadillac CTS, SRX, STS and XLR models, and in some BMWs of that era. In Spanish there's almost nothing on them beyond sales listings. This guide pulls together what GM's service manual and bulletins say: which cars have it in Mexico, what fails by symptom, limp mode, the codes, test values, the fluid and TSS parts. If you don't know which transmission your Cadillac has, see our GMC, Buick and Cadillac guide.

What are the 5L40E and 5L50E?

What it isA GM Hydra-Matic 5-speed automatic, longitudinal, rear-wheel or all-wheel drive, built in Strasbourg, France
5L40E or 5L50EGM used the 5L50E with the 4.6 Northstar V8 and the 5L40E with the V6s, including the all-wheel-drive SRX
Its 4-speed siblingThe 4L40E: GM says it shares identical packaging and that they're fully interchangeable; that's why TSS parts list all three
ComputerIt has its own (TCM), in the engine compartment
SolenoidsThree shift solenoids (1-2, 2-3 and 4-5), a pressure control solenoid and a converter PWM solenoid
ID plateOn the side of the case, toward the rear and above the pan: "HYDRAMATIC STRASBOURG MADE IN FRANCE"; the unit code starts with the year and a G, for example 5GLG
DipstickNone: the level is checked at the plug, with the engine running
On BMWsBMW calls it GM5, and in the same years it also used the ZF 5HP19: check the plate

Which cars have it in Mexico?

Cadillac CTS 2003 to 2007 (V6)"Transmisión automática electrónica de 5 velocidades 5L40-E" in 2003 and 2004; then "Hydramatic, automática de 5 vel.": the 5L40E
Cadillac SRX 2004 to 2007"Hydra-matic 5L40-E" with the 3.6 V6, including all-wheel drive, and "5L50-E" with the 4.6 V8
Cadillac STS 2005 to 2007"5L50-E" with the V8 and "5L40-E" with the 3.6 V6
Cadillac XLR 2004 to 2006"Hydra-Matic de 5 velocidades": the 5L50E, per GM
SRX and STS V8 2007Cadillac México still said 5L50-E in January 2007, but in the US the 2007 V8 is already a 6-speed: check the label (MYB or MYC are 6-speeds)
BMW 323iA, 330iA and 528iA (2000 and 2001)Automatics; BMW México doesn't say which: it can be the GM5 or the ZF 5HP19, depending on engine and build date
Pontiac Solstice 2006 and 2007No: in Mexico it was only sold with a 5-speed Aisin manual

Cadillac México did name the transmission on its 2003 to 2006 spec sheets. BMW's sheets of that era only said "automático", and BMW used two different units, so on a BMW check the plate.

5L40E and 5L50E problems by symptom

These are the symptom tables in GM's service manual (US 2005 Cadillac CTS) and what its bulletins say:

Only uses 5th and starts in 5thA stuck feed limit valve, a bad connection to the shift solenoids or an active limp mode: read the codes
Won't move in any positionForward clutch and its sprag, the pump (vanes, rotor, screen), the low sprag and the planetary
No reverse, or slips in reverseDirect and reverse clutch, reverse lockout valve, a leaking converter PWM solenoid and the shift lever adjustment
Slips during shiftsAccumulator pistons and seals, check balls, the pressure control solenoid and the pump
No 4th, or slips in 4thStuck 3-4 shift valves and the direct and reverse clutch
No converter lockupThe lockup regulator valve, the converter PWM solenoid (stuck, damaged, or with a damaged O-ring or screen), the pump and the turbine shaft O-ring
OverheatsThe pressure regulator valve and the pump, and a contaminated pressure control solenoid or damaged O-rings
Shudders or "chuggles" under light load after lockupIn the US, GM reprogrammed the transmission computer; only if it persisted above 40,234 km (25,000 mi) did it replace the converter, flush the cooler and change the fluid
Engine braking when lifting off, or starts in 2nd or 3rd in winterIt's normal: GM designed it to feel like a manual, and winter mode (the snowflake) starts in a higher gear
Late shifts on cold mornings (0 °C or colder)It's normal: a warm-up schedule delays the shifts

Stuck in 5th: limp mode

With a major electrical fault, the computer turns off every solenoid. The transmission stays in 5th if it had already made the 1-2 shift in that ignition cycle, or in 4th if not; line pressure goes to maximum, the converter doesn't lock up and the lever stops selecting the forward gears. If it's in 5th, you get 4th by briefly stopping and restarting the engine. GM warns the transmission heats up quickly in 4th or 5th, especially in traffic. Unlike other GM units, limp mode here isn't 3rd.

Cadillacs warn with messages: "Change Transmission Fluid" when fluid life drops below 10 %, "Service Transmission" with a transmission fault, and "Trans Hot Idle Engine" when the fluid goes above 132 °C (269 °F) for a minute.

5L40E and 5L50E trouble codes

P0741The converter slips with lockup commanded. GM checks the level and that the cooler lines aren't pinched, plugged or twisted
P0742The converter stays locked up; GM says it's almost always the controls (a stuck solenoid or valve), not the converter
P0748Pressure control solenoid circuit: maximum line pressure, no check engine light (guide)
P0751 and P07521-2 solenoid or valve: no 1st, 4th or 5th (stuck on), or no 2nd or 3rd (stuck off)
P0756 and P07572-3 solenoid or valve: no 1st or 2nd, or no 3rd, 4th or 5th
P0761 and P07624-5 solenoid or valve; with P0762 there's no 5th
P0973 to P09801-2, 2-3 and 4-5 solenoid circuits; several put the transmission in limp mode (guide)
P2763 and P2764 (P1866 and P1867 in 2003)Converter PWM solenoid circuit
P0716, P0717, P0722 and P0723Input and output speed sensors; GM first checks they're properly tightened (guide)
P0711 to P0713Fluid temperature sensor (guide)
P1815 and P1820 to P1826 (P1915 from 2006)Internal position switch
P0218Fluid overtemperature
P0700The transmission computer asked to turn on the check light: read the codes stored in it

The check engine light goes off after six consecutive trips without the fault. On the 2003 CTS, the transmission computer wouldn't talk to scan tools other than GM's, per a US bulletin. You can look up other codes in our diagnosis by code.

Test values

1-2, 2-3 and 4-5 shift solenoids15.0 to 17.0 Ω at 20 °C (17.9 to 20.3 Ω at 70 °C)
Pressure control solenoid3.5 to 4.6 Ω at 20 °C (4.2 to 5.5 Ω at 70 °C)
Converter PWM solenoid10.0 to 11.5 Ω at 20 °C (11.8 to 13.6 Ω at 70 °C)
Input and output speed sensors325 to 485 Ω at 20 °C (385 to 575 Ω at 70 °C)
Any circuit to the caseMore than 50 kΩ
Line pressure at 1,300 rpmWith 0.1 A on the pressure solenoid, 1,194 to 1,355 kPa, or 173 to 197 psi (maximum); with 1.1 A, 288 to 440 kPa, or 42 to 64 psi (minimum)

These are the values in GM's service manual for the US 2005 Cadillac CTS. For the pressure test, the scan tool raises the pressure solenoid current from 0 to 1 A in 0.1 A steps, five seconds each, and GM says not to go past two minutes in total.

Which fluid does it take, and how is it checked?

GM specified DEXRON-III, and its bulletin 04-07-30-037E says that from 2006, GM models that used DEXRON-III must take DEXRON-VI, which can be mixed in any proportion. It holds about 8.5 liters (9 quarts) in total. For BMWs we didn't find BMW's spec: use your car's.

It has no dipstick. GM checks the level with the fluid at operating temperature: move the lever through every position, leave the car level and in P with the engine running, and remove the level plug. The fluid should be even with the bottom of the hole; if it's low, add half a liter at a time until it drips out. GM warns the plug must never come out with the engine off, because a lot of fluid will drain.

Cadillacs have a fluid life monitor: below 10 % "Change Transmission Fluid" appears, and GM says to change it within 322 km (200 miles) and reset the monitor. When changing it, GM fits a new drain plug and two new seals on the filter neck; the pan gasket can be reused if its surface is fine. If the fluid comes out milky or like a "strawberry milkshake", it has water or coolant, and GM calls for replacing all rubber seals, the friction plates, the nylon parts and the converter. More on the cooler in our cooler guide.

5L40E and 5L50E myths

  • "The 5L40E is a ZF or BMW transmission." It's a GM Hydra-Matic built in France; BMW calls it GM5 and names its ZF units separately.
  • "4L40E is a typo." GM also sold the 4L40E, a 4-speed with identical packaging.
  • "It's sealed for life." GM gave it a fluid life monitor that asks for a change, and a procedure to check the level.
  • "Limp mode is 3rd gear." On this unit it's 5th, or 4th, and the lever stops selecting the forward gears.
  • "Starting in 3rd with the snowflake light on is a fault." That's winter mode.
  • "It shudders after lockup: it needs a rebuild." GM fixed it by reprogramming the transmission computer; the converter only if it persisted.
  • "P0742 is the converter." GM says it's almost always the controls: a stuck solenoid or valve.
  • "Every BMW of that era has the GM unit." BMW used the ZF 5HP19 on the 2.5 engine from March 2000.
  • "Any 5L40E will do." BMW and Cadillac units have different ratios, and GM separates 2WD and AWD parts: confirm with the code on the plate.

How is it diagnosed?

  • Check the fluid level and condition at the plug, with the engine running and the fluid hot.
  • Read the codes in the transmission computer, not just the engine's: P0700 only says there's a transmission fault.
  • If it's stuck in 5th or 4th, find the cause of limp mode: the solenoid circuits, a sensor or the computer.
  • Measure the solenoids and sensors against the values above, and check that no circuit reads under 50 kΩ to the case.
  • Run the line pressure test with the scan tool.
  • Before replacing the converter for shudder or P0741, check the cooler lines and whether there's a reprogramming.

GM didn't sell the case on its own in the US: if it was damaged, it replaced the whole transmission. To compare with GM's other automatic of that era, see our 4L60E guide.

See 5L40E and 5L50E parts

TSS parts for the 5L40E and 5L50E

The 5L40E and 5L50E page has every TSS part for these units. These are the ones that match the jobs in this guide:

Fluid and filter changeGM shallow-pan filter or BMW/GM deep-pan filter, and 20-hole pan gasket
Harsh or soft shifts, P0748Pressure control solenoid, 2003 on or 1995 to 2002
Converter: P0741, P2763, P2764, or no reverse from a leakConverter PWM solenoid
Won't move (forward clutch)Forward clutch friction plates and friction plate pack
PumpRotor vane
Leak at the shift shaftShift shaft seal

Pick the filter by pan depth (BMWs use a deep pan) and confirm the pressure solenoid against the old part. TSS has no shift solenoids, sensors, position switch, valve body or computer for this unit. To test other solenoids, see our transmission solenoid guide.

TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • What transmission does the 2003 to 2007 Cadillac CTS have?

    GM's 5L40E, a 5-speed automatic. Cadillac México named it that way on its 2003 and 2004 spec sheets.

  • What's the difference between the 5L40E and the 5L50E?

    They're the same family: GM used the 5L50E with the 4.6 Northstar V8 (SRX, STS and XLR) and the 5L40E with the V6s, including the all-wheel-drive SRX.

  • Why is my Cadillac stuck in 5th?

    That's this unit's limp mode: with a major electrical fault it turns off every solenoid and stays in 5th, or in 4th if it hadn't made the 1-2 shift. Read the codes in the transmission computer.

  • Does the 5L40E have a dipstick?

    No. The level is checked at the plug, with the car level, in P, the engine running and the fluid hot; the plug never comes out with the engine off.

  • Which fluid does the 5L40E take?

    GM specified DEXRON-III, and from 2006 GM calls for DEXRON-VI instead. It holds about 8.5 liters (9 quarts) in total.

  • What should its solenoids measure?

    Per GM, at 20 °C: the shift solenoids 15 to 17 Ω; the pressure control solenoid 3.5 to 4.6 Ω; and the converter PWM solenoid 10 to 11.5 Ω.

  • Does my BMW 330i have this transmission?

    It can: BMW calls it GM5, but in that era it also used the ZF 5HP19. Check the plate on the transmission.

  • Is there a campaign or warranty for the 5L40E?

    We found no US recalls for this transmission and no campaigns in Mexico.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.