Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

GM 4T40E and 4T45E problems: Malibu, Cavalier, Cobalt

TSS editorial team · · 17 min read

Technician inspecting an automatic transmission clutch drum and stator pump shaft on a workbench for GM 4T40E and 4T45E
In short
  • The 4T40E (RPO MN4) and 4T45E (MN5) are GM's 4-speed automatics for front-wheel-drive cars: in Mexico, the Malibu, Cavalier, Sunfire, Grand Am, Pontiac G4, G5 and G6, HHR and Captiva Sport 2.4.
  • The 4T45E is a 4T40E variant with 10 % more torque capacity. They share the same ratios, but the chain and differential change by car, so they aren't always interchangeable.
  • What GM documented most in the US: the valve body (P0741, P0742, P0751 to P0757, P1811), no movement or no reverse, converter shudder, and electrical faults in switches, sensors and the harness.
  • There's no dipstick on the versions GM documents: the level is checked at a plug, with the engine running and the fluid at 40 °C or more. It takes DEXRON-VI and about 6.5 liters for a pan drop.
  • GM gives 19 to 24 Ω for the shift solenoids, 10 to 11 Ω for the converter solenoid and 3 to 5 Ω for the pressure solenoid, at 20 °C.

The 4T40E and 4T45E are the 4-speed automatics GM used in its compact and midsize front-wheel-drive cars: in Mexico, the Malibu, Cavalier, Sunfire, Grand Am, Pontiac G4, G5 and G6, HHR and Captiva Sport 2.4. If yours slips, won't move, has no reverse or sets solenoid codes, here are the failures GM documented, its codes, the test values from its service manual, how to check the fluid without a dipstick and the TSS parts that fit it.

What are the 4T40E and 4T45E?

GM introduced the 4T40-E (RPO code MN4) in 1995, and the 4T45-E (MN5) in 1999, as a variant with 10 % more torque capacity for the 3400 V6 in the Grand Am and Alero. Both were built in Windsor, Canada, and share the same ratios: 2.96, 1.63, 1.00 and 0.68, with a 2.14 reverse.

What changes from car to car is the final drive: the chain that carries power from the converter to the gearbox comes in two sizes (32/38 or 35/35 teeth) and the differential in two ratios (3.05 or 3.29), so the overall final drive can be 3.05, 3.29, 3.63 or 3.91. That's the number GM Mexico printed as the "relación final del eje". That's why two 4T45-Es aren't simply interchangeable: compare the RPO code, the final drive and the engine before swapping one for another.

Inside it has two bands (intermediate/4th and low/reverse), five clutches (forward, coast, 2nd, reverse and direct), an input sprag and two roller clutches. The computer controls it with two shift solenoids, a converter PWM solenoid and a pressure control solenoid; the temperature sensor sits inside the pressure switch assembly, and it has input and output speed sensors. Up to 2005 the engine computer controlled it; GM wrote its 2006 files for the Ion, Cobalt and HHR with a separate transmission computer. This is how to identify it:

RPO code (service parts label)MN4 is the 4T40-E and MN5 the 4T45-E; in some bulletins GM also uses ME7 for the 4T45-E
ID plateA metal plate on the case, with the model, date and part number
Ratios2.96, 1.63, 1.00 and 0.68; reverse 2.14. The 4T65-E, used in bigger V6 cars and vans, has different ones
Overall final drive3.05, 3.29, 3.63 or 3.91, depending on its chain and differential
DipstickNone on the versions GM documents: the level is checked at a level control plug
Fluid for a pan dropAbout 6.5 liters; 9.0 for an overhaul and 12.2 dry

Which cars have the 4T40E or 4T45E in Mexico?

These are the GM Mexico pages we found; on four of them, GM names the transmission outright:

Chevrolet Malibu, 1997 to 2003 (2.4 and 3.1 V6)In 2001: "transmisión 4T40-E automática electrónicamente controlada de 4 velocidades con sobremarcha"
Chevrolet Malibu, 2004 to 2010 (2.2, 2.4 and 3.5 V6)"Transmisión automática de 4 velocidades Hydra-Matic": the 4T45-E (the 2004 2.2, the 4T40-E according to GM). From 2009, some 2.4 versions are already 6-speeds
Chevrolet Cavalier, 2001 to 2005"Transmisión automática de 4 velocidades" in the automatic packages: the 4T40-E
Pontiac Sunfire, 1996 to 2006"Transmisión automática electrónica de cuatro velocidades": the 4T40-E
Pontiac Grand Am 3.4 V6, 2001 to 2005In 2001: "transmisión automática de cuatro velocidades con sobremarcha 4T45E"
Pontiac G4 and G5, 2006 and 2007"Transmisión automática de 4 velocidades 4T45-E"
Pontiac G6 3.5 V6, 2005 to 20074-speed automatic; given the engine and final drive, the 4T45-E. The 2007 G6 3.6 is already a 6-speed
Chevrolet HHR, 2006 to 2009"Transmisión automática de 4 velocidades": the 4T45-E
Chevrolet Captiva Sport 2.4, 2008 to 2010"Transmisión automática de 4 velocidades": the 4T45-E

Watch the Cavalier: according to GM Mexico, the 1996 and 1997 automatic was a 3-speed hydraulic unit (the 3T40); the 4T40-E shows up on its Cavalier pages in 2001. The Malibu, Captiva Sport and G6 with the 3.6 V6 (6-speeds), the Venture, Uplander, Impala and Grand Prix (4T65-E), the 2005 to 2008 Equinox (Aisin) and the Optra (ZF 4HP16) aren't part of this family. More models in our Chevrolet and Captiva guides.

The Cobalt was sold in Mexico as the Pontiac G4. The Saturn Ion, Aura and Vue and the Oldsmobile Alero on Mexican roads are imports: in the US, GM gave them the 4T40-E or 4T45-E depending on the year and engine. Confirm yours with the RPO code, not the badge.

4T40E and 4T45E problems by symptom

This table combines the bulletins GM published in the US and its service manual:

Harsh shifts, slipping, no drive or no reverse, with solenoid codesThe valve body: GM published how to recondition it for P0741, P0742, P0751, P0752, P0756, P0757 and P1811
No movement in D or R and the fluid reads overfullGM documented cases where the converter was left empty of fluid
No reverse or binds in reverse, with P0756A GM bulletin for 2008 4T45-Es; on some 2008 and 2009 cars, the direct clutch
Shudder or chuggle between 72 and 96 km/hThe converter clutch, applied (P0741, P0742)
The engine stalls when stoppingThe converter stayed locked (P0742)
Stuck in 2nd or slips in 4thElectrical faults in the shift or converter solenoids (P0753, P0758, P1860)
Flares in neutral or in D, or no 1-2 upshiftThe pressure switch assembly (P1810, P1815)
Slips under load in 2nd, 3rd or 4thGM published a bulletin with this symptom for the 4T40-E, 4T45-E and 4T65-E
Electrical codes that come and go (Cobalt and HHR)The harness pinched near the engine oil filter, or the 20-pin connector terminals
Fluid leaksThe cooler line seals or the axle seals; also the shift shaft, the converter and the pan and side cover gaskets

Stuck in 2nd: shift solenoids and limp mode

According to the range table in GM's service manual, with both shift solenoids off the transmission sits in 2nd in D; with no current, the pressure solenoid gives maximum pressure and the converter solenoid doesn't lock. If a solenoid or a shift valve sticks, the transmission follows a pattern GM documented for each code. These are the gears you get when the computer commands 1st, 2nd, 3rd and 4th:

P0751 (1-2 solenoid stuck off)2-2-3-3: no 1st or 4th
P0752 (1-2 solenoid stuck on)1-1-4-4: no 2nd or 3rd
P0756 (2-3 solenoid stuck on)4-3-3-4: no 1st or 2nd
P0757 (2-3 solenoid stuck off)1-2-2-1: no 3rd or 4th

GM makes clear these codes set from a stuck solenoid or a stuck shift valve, and says to check for contaminated fluid or plugged passages before replacing parts. The solenoids' electrical codes are P0753 and P0758 on units controlled by the engine computer, and P0973 to P0977 on those with a separate computer. More in our shift solenoid codes guide.

Harsh shifts or slipping: valve body and pressure

In 2007, GM published US information on reconditioning the 4T40-E and 4T45-E valve body for harsh shifts, slipping, no drive or no reverse, with codes P0741, P0742, P0751, P0752, P0756, P0757 and P1811; the bulletin lists 1997 to 2007 Malibu, Cavalier, Sunfire, Alero, Grand Am, Saturn, G5, G6 and HHR models. Earlier, in 2002, it published a pressure control solenoid replacement for the 4T40-E, 4T45-E and 4T65-E, and engineering changes to the valve body, pressure regulator valve and 2-3 accumulator valve of 2002 and 2003 4T45-Es. For 2007 to 2009 units with soft or erratic shifts, its diagnostic guide compares actual with desired line pressure.

P1811 (maximum adapt with a long shift) doesn't turn on the check engine light, but it raises line pressure to maximum. GM asks whether the car is loaded or towing in overdrive and checks the fluid level and line pressure. More in our guides to the valve body and the pressure control solenoid.

No drive or no reverse

GM published three leads in the US: a bulletin for cars that won't move in either direction, where the fluid can read overfull because the converter was left empty; a 2008 one for the 4T45-E with no reverse, binding in reverse or no movement, with P0756; and a 2008 and 2009 one (Cobalt, HHR and G5, among others) that points to the direct clutch for no movement, no reverse or slipping. Before tearing it down, check the fluid level, the codes and line pressure. More causes in our guide to when reverse won't engage.

Converter shudder: P0741 and P0742

GM published bulletins for shudder or chuggle with the converter locked between 72 and 96 km/h on 2001 Cavaliers and Sunfires; for firm shifts, shudder and P0742 on 2003 Aleros, Cavaliers, Grand Ams, Malibus and Sunfires; and for P0741 (the converter won't lock) on the 2002 Malibu. Its service manual explains that transmission-caused shudder only shows up as the lock-up applies or releases; if it continues with the converter fully locked, it's usually the engine or the rest of the driveline. As transmission causes, it lists leaking turbine shaft seals, a restricted release orifice, a surface distorted by over-long converter bolts and the converter clutch lining.

P0741 sets when the converter slips more than 150 rpm with lock-up commanded, and P0742 when it stays locked: GM warns the engine can stall when stopping. With P0741, GM says to check the fluid level, hot mode and plugged or pinched cooler lines. Check the fluid cooler too.

Electrical faults: pressure switches, sensors and harness

The pressure switch assembly, bolted to the valve body, tells the computer which range the lever is in and carries the fluid temperature sensor. In the US, GM published bulletins for flares in neutral or D and no 1-2 upshift with P1810 and P1815 (1995 to 2003) and for a false P1815 (2003). On 2000 to 2004 units it documented input speed sensor codes (P0716 and P0717) and solenoid codes (P0753, P0758, P1860), and on 2002 to 2004 Cavaliers and Sunfires, slipping in 4th or holding 2nd with P0753, P0758 and P1860.

On the 2005 to 2010 Cobalt and the 2005 to 2011 HHR, with electrical or communication codes that come and go, GM says to check the harness under the engine cover, which can get pinched against the block near the oil filter, and then the terminal fit at the 20-pin connector. More in our guides to speed sensors, the temperature sensor and lost communication.

Fluid leaks

In 2000 and 2001, GM published a US bulletin for leaks at the cooler line seals or at one or both axle seals, and another for a mismachined sealing surface on the 4T40-E forward clutch housing (2000 Cavalier and Sunfire). Its service manual also lists as leak points the case, the shift shaft seal, the connector seal, the converter seal, the level control plug, the output sensor O-ring, the vent cap and the pan and side cover gaskets. How to find the source, in our guide to fluid leaks.

4T40E and 4T45E trouble codes

These are the codes in GM's diagnostic files and service manual. Some changed numbers when the transmission got its own computer, in 2006:

P0218Fluid above 130 °C for 10 minutes (2006)
P0502 and P0503; from 2006, P0722 and P0723Output speed sensor: low or intermittent signal
P0705Range sensor: impossible combination (2006)
P0711, P0712 and P0713Fluid temperature sensor: impossible reading, shorted (above 150 °C) or open (below −40 °C)
P0716 and P0717Input speed sensor: the signal drops suddenly, or reads under 100 rpm with the car moving
P0741The converter won't lock: it slips more than 150 rpm with lock-up commanded
P0742The converter stays locked; it can stall the engine
P0748 and P0961Pressure control solenoid: circuit and performance
P0751 and P07521-2 shift solenoid: performance (2-2-3-3 and 1-1-4-4 patterns)
P0756 and P07572-3 shift solenoid: performance (4-3-3-4 and 1-2-2-1 patterns)
P0753 and P0758; from 2006, P0973 to P0977Shift solenoids: electrical fault
P1810Pressure switches: impossible range. GM warns that unplugging the connector with the key ON sets it
P1811Maximum adapt and long shift: no check engine light, but line pressure goes to maximum
P1815, P1816 and P1818Pressure switches: start in the wrong range, P or N with a drive ratio, or D with a reverse ratio
P1860; from 2006, P2763 and P2764Converter PWM solenoid: electrical fault
P1887; from 2006, P0842 and P0843Converter release switch, inside the pressure switch assembly

GM doesn't include P0894 to P0897 in its code lists for these units. Look up any other code in our diagnosis by code, and the range sensor code in our P0705 guide.

Test values

These come from GM's service manual for the 2006 Malibu 2.2 (4T45-E), at 20 °C and measured at the transmission's 20-pin connector:

1-2 and 2-3 shift solenoids (pins A–E and B–E)19 to 24 Ω (24 to 31 at 100 °C)
Converter PWM solenoid (T–E)10 to 11 Ω (13 to 15 at 100 °C)
Pressure control solenoid (C–D)3 to 5 Ω (4 to 7 at 100 °C)
Fluid temperature sensor (L–M)3,106 to 3,923 Ω (164 to 190 at 100 °C)
Input speed sensor (S–V)625 to 725 Ω (750 to 835 at 100 °C)
Output speed sensor (at its own connector)1,500 to 1,750 Ω (1,750 to 1,900 at 100 °C)
Any solenoid or sensor to the caseSolenoids, more than 250 kΩ; sensors, more than 10 MΩ (the temperature sensor, more than 20 MΩ)

Line pressure, in Park with the fluid at 70 °C, should be 1,041 to 1,138 kPa with no current to the pressure solenoid, and drop as the computer gives it more current, down to 289 to 330 kPa at 1.1 A. GM says not to exceed 2 minutes per test and to repeat it three times.

Which fluid does it take, and how do you check it without a dipstick?

GM filled it with DEXRON-III; its later manuals call for DEXRON-VI, which GM approves in place of III. A pan drop takes about 6.5 liters; an overhaul, 9.0, and dry, 12.2. The versions GM documents have no dipstick, and the level is checked like this, according to its service manual:

  • Idle the engine until the fluid reaches 40 °C or more, and move the lever through every position with the brake pressed.
  • In Park, with the car level and the engine running, remove the vent cap and then the level control plug, on the converter side.
  • The correct level reaches the bottom edge of the hole. If it's low, add fluid half a liter at a time until it drips out.
  • If it takes more than 1.5 liters, look for a leak.

We couldn't confirm the 2008 to 2010 units (Malibu and Captiva Sport 2.4): check whether yours has a dipstick. GM points out that fluid darkens with normal use and that isn't always contamination; if it smells burnt or is dark brown, inspect the pan, and if it's milky, it has coolant from the radiator cooler. More in our guide to burnt fluid, debris or water.

How often should the fluid be changed?

GM said in 1999 that in normal use the fluid didn't need changing, and GM Mexico repeated in 2001 that on the Grand Am "el líquido no necesita ser cambiado jamás" (the fluid never needs changing). But GM always set an 80,000 km interval for severe use, GM Mexico announced 160,000 km for the 2001 Malibu, and GM's 2006 maintenance schedule calls for fluid and filter at 160,000 km in normal use. If your use is heavy (heat, traffic, hills or towing), the 80,000 km interval makes sense.

US recalls

The recalls on these cars were for the shift cable, not the transmission. The biggest (14V224, from 2014) covered 2004 to 2008 Malibus, 2004 to 2007 Malibu Maxxes, 2005 to 2008 Pontiac G6s and 2007 and 2008 Saturn Auras with the 4-speed automatic: the cable could break and the car could roll even with the lever in P. Others (12V460 and 09V073) also involved the cable. And in 2001, GM ran a US campaign for 2.4 Aleros, Cavaliers, Grand Ams and Sunfires with the 4T40-E, because a bearing in the pump cover could fail early. We found no recalls or PROFECO notices for Mexico. If your car came from the US, check its VIN.

4T40E and 4T45E myths

  • "The 4T40E and the 4T45E are the same and interchangeable." They're the same family, but the 4T45-E handles more torque, and the chain, differential and bellhousing change with the engine. Compare the RPO code, the final drive and the engine.
  • "It's sealed: the fluid never gets changed." GM said so in 1999 for normal use, but it always set 80,000 km for severe use, and by 2006 it called for fluid and filter at 160,000 km.
  • "Every automatic Cavalier has the 4T40E." The 1996 and 1997 ones sold in Mexico were 3-speeds.
  • "The 1997 to 2003 Malibu has the 4T60E or 4T65E." GM and GM Mexico say 4T40-E.
  • "P0751 or P0756 means replace the solenoid." GM says they set from a stuck solenoid or a stuck shift valve, and its bulletin is about reconditioning the valve body.
  • "Its most common failure is overheating." We found no GM bulletin on overheating for these units; GM only defines its hot mode, at 140 °C.
  • "The Optra has the 4T40E." The Optra uses the ZF 4HP16 (see our Aveo and Optra guide).

How is it diagnosed?

  • Check the fluid level and condition at the level control plug, hot, as explained above.
  • Read the codes with a scan tool that reaches the computer controlling the transmission: the engine computer up to 2005, or the transmission computer from 2006.
  • If it's stuck in one gear, compare the pattern with the solenoid table and measure the solenoids at the 20-pin connector against GM's values.
  • Measure line pressure with a gauge, commanding the pressure solenoid with the scan tool in Park or Neutral.
  • On a Cobalt or HHR with codes that come and go, check the harness near the oil filter and the 20-pin connector.
  • If there's metal or clutch material, or the fluid smells burnt, the transmission needs a rebuild; if it's milky, check the radiator cooler.
  • After repairing or replacing the transmission, reset the adaptives with the scan tool, as GM requires.

See 4T40E and 4T45E parts

TSS parts for the 4T40E and 4T45E

The 4T40E and 4T45E page has every TSS part for these transmissions. These are the ones that match the failures in this guide:

Shift solenoid codes (P0751 to P0758, P0973 to P0977)Shift solenoid; the transmission uses two identical ones, 1-2 and 2-3
Line pressure (P0748, P0961)1995 to 2002 pressure control solenoid and 2003 on
Converter (P0741, P0742, P1860, P2763, P2764)Converter PWM solenoid
P1810, P1815, P1887 or temperature (P0711 to P0713)Pressure switch assembly
P0716, P0717 or the output sensorSpeed sensor
20-pin external connector and harnessHarness repair and test kit
LeaksAxle seal, axle seal with bushing, pump seal, shift shaft seal, pan gasket and chain cover gasket
Fluid serviceFilter and pan with magnet
No 4th or slips in 4thIntermediate and 4th band
Full rebuildRojo overhaul kit or Dorado (H-D), friction plate kit, friction plate pack, steel plate pack, converter bushing, case bushing and drive sprocket washer

Confirm with your distributor whether the speed sensor you need is the input or the output one (they measure differently), which pressure switch design your transmission has, which axle seal goes on each side and whether the overhaul kit covers your year. The difference between the Rojo and Dorado kits is in our guide to TSS overhaul kits.

TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • What's the difference between the 4T40E and the 4T45E?

    They're the same family, with the same ratios (2.96, 1.63, 1.00 and 0.68, reverse 2.14). GM introduced the 4T45-E in 1999 as a 4T40-E variant with 10 % more torque capacity, for the 3400 V6 in the Grand Am and Alero. RPO code MN4 is the 4T40-E and MN5 the 4T45-E. The chain and differential change by car.

  • Which cars have the 4T40E or 4T45E in Mexico?

    According to GM Mexico: the 1997 to 2003 Malibu (4T40-E), the 2001 to 2005 4-speed automatic Cavalier and the Sunfire (4T40-E), and the 2001 to 2005 Grand Am and the Pontiac G4 and G5 (4T45-E). With the 4-speed, also the G6 3.5, the 2004 to 2010 Malibu, the HHR and the 2008 to 2010 Captiva Sport 2.4. The 1996 and 1997 automatic Cavalier was a 3-speed.

  • Where do you check the fluid if there's no dipstick?

    At the level control plug, on the converter side. According to GM: engine idling, fluid at 40 °C or more, car level, lever in P and the vent cap removed; the level should reach the bottom edge of the hole. If it takes more than 1.5 liters, there's a leak.

  • Which fluid does the 4T45E take, and how much?

    GM specified DEXRON-III at first and DEXRON-VI in its later manuals; DEXRON-VI replaces III. A pan drop takes about 6.5 liters; an overhaul, 9.0, and dry, 12.2.

  • How often should its fluid be changed?

    GM said in 1999 that in normal use it didn't need changing, but it set 80,000 km for severe use. GM Mexico announced 160,000 km for the 2001 Malibu, and GM's 2006 schedule calls for fluid and filter at 160,000 km. With heavy use, the shorter interval makes sense.

  • What do P0751, P0752, P0756 and P0757 mean?

    That the computer saw the wrong shift pattern: P0751 gives 2-2-3-3, P0752 gives 1-1-4-4, P0756 gives 4-3-3-4 and P0757 gives 1-2-2-1. GM blames a stuck solenoid or shift valve, says to check for contaminated fluid or plugged passages, and published US information on reconditioning the valve body.

  • My car won't move in D or R. Is the transmission destroyed?

    Not necessarily. GM documented no-movement cases where the converter was left empty and the level read overfull, no-reverse cases with P0756 and direct clutch problems, all in US bulletins. Check the level, codes and line pressure before tearing it down.

  • Are the 4T40E and 4T45E interchangeable?

    Not always. They share the same internal ratios, but the 4T45-E handles more torque, and the chain, differential and bellhousing change with the engine, so the overall final drive ranges from 3.05 to 3.91. Before swapping one for another, compare the RPO code, the final drive and the engine.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.