Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

Toyota U340E and U341E: Corolla and Yaris problems

TSS editorial team · · 11 min read

Mechanic reaching into a compact front-wheel-drive engine bay with a wrench servicing a Toyota U340E and U341E transaxle
In short
  • The U340E and U341E are Toyota 4-speed front-drive automatics: the U340E goes with the Yaris 1.5 and the U341E with the 1.8 in the 2009-on Corolla.
  • In Mexico, the 4-speed automatic Corolla ran until about 2016 and the Yaris 1.5 until about 2017; Toyota México doesn't publish the transmission code.
  • "Stuck in 3rd" is usually limp mode: an S1 solenoid fault leaves only 3rd and 4th, and several sensors block 4th.
  • Toyota checks other codes first, then the solenoid, the valve body, the converter and, last, the transmission; its solenoid codes also set with damaged clutches.
  • They take Toyota ATF WS, which isn't compatible with T-IV or Dexron, and they do have a dipstick: check the level hot, at 70 to 80 °C.

The U340E and U341E are the 4-speed automatics of the Yaris 1.5 and the Corolla 1.8 before the CVTs arrived. Search for them on Google Mexico and almost everything is a sales listing. This guide pulls together what Toyota's service manuals and bulletins say: which cars have them, what fails by symptom, what the codes mean, the test values, the fluid and TSS parts. If you don't know which transmission your car has, see which transmission does my Toyota have.

What are the U340E and U341E?

What it isA Toyota 4-speed front-drive automatic with electronic control (ECT)
EngineU340E: the Yaris 1.5 (1NZ-FE). U341E: the 1.8 (2ZR-FE) in the 2009-on Corolla
ComputerIt has none of its own: the engine computer runs it
All-wheel driveThe AWD version is called U341F (US Matrix)
SolenoidsFive: S1, S2 and ST for shifting; SLT for line pressure; and SLU for the converter (an SL on other versions)
Serial numberStamped on the case: on top, above the differential, or in the center, behind the bell housing, next to the vent hose
DipstickYes: the level is checked hot, at 70 to 80 °C (158 to 176 °F)
Don't confuse withA245E (2003 to 2008 Corolla), U250E (5-speed, 2.4 engine), U441E (a different unit) and the K313 CVT

Don't confuse it with the U441E: the TSS catalog groups that one with the Aveo's Aisin AW81-40LE and also lists it for the Yaris, but it's a different unit and its parts aren't the same. To be sure, read the plate on the case or order by the car's VIN.

Which Toyotas have it in Mexico?

Corolla 1.8, 2009 to 2013"Automática de 4 velocidades": U341E, per Toyota's US documents for the same engine
Corolla 1.8, 2014 to about 2016"Automática de 4 velocidades" on Toyota's site through October 2015; by August 2016 it says CVT. Probably U341E, like the 2014 to 2016 US Corolla 4-speed automatic
2009 Corolla CE (126 hp 1.8)"Automática 4 velocidades", but with the older engine: we didn't confirm whether it's U341E or A245E
Yaris 1.5, 2006 to about 2017 (hatchback and sedan)"Automática de 4 velocidades" (with ECT or ECT-i): probably U340E, the unit named in the 2009 US Yaris manual
Corolla and Matrix 1.8, 2003 to 2008No: they're the A245E family
Corolla XRS 2.4 (2009 to 2011) and Matrix XR 2.4 (2009)No: "automática secuencial de 5 velocidades", the U250E
Corolla 2017 onNo: CVT
Yaris R 2016 to 2019 and Yaris 2019 to 2024No: Mazda 6-speed automatic and CVT

Toyota México never publishes the transmission code: we infer it from Toyota's US documents for the same engine and number of speeds. In the US, the U340E is also in the Echo and the Scion xA and xB, and the U341E in the 2009 to 2014 Matrix; in Mexico, the 2009 automatic Matrix was the 2.4 5-speed.

U340E and U341E problems by symptom

This is Toyota's symptom table for the U341E, in its order. Toyota checks the electrical side before the mechanical one:

Stuck in 3rd or no 4thLimp mode from a solenoid or a sensor (below); read the codes before opening the transmission
Harsh shifts in every gear, or shift points too high or too lowThe SLT solenoid (line pressure) and the valve body; run the pressure test
Bump on the 3-4 upshift or the 4-3 downshiftThe ST solenoid, the valve body and the overdrive and 2nd brake
Harsh engagement into DValve body, forward clutch and No. 2 one-way clutch
Harsh engagement into RC3 accumulator, valve body, reverse clutch and 1st and reverse brake
Slips or shudders going forwardValve body, oil strainer (filter), converter clutch, and the clutches and brakes
Won't move in D or RFluid level first; then the manual valve, valve body, planetary gear unit, forward clutch, No. 2 one-way clutch, reverse clutch and 1st and reverse brake
No converter lockup, or the engine stalls when starting off or stoppingThe converter solenoid (SLU or SL, depending on the version), the valve body and the converter clutch
Dark red or black stain between the engine and the transmission (Corolla)It's not always the transmission: on the 2009 to 2017 Corolla, Toyota found engine oil from a block oil galley plug (US bulletin)
Won't shift out of P and several lights come on after a very cold nightNot the transmission: an IG1 relay that freezes below −10 °C (14 °F) (US bulletins for the 2007 Yaris and the 2006 to 2009 Corolla)

Stuck in 3rd: limp mode

With two shift solenoids, the computer builds all four gears: S1 and S2 on give 1st; S1 only, 2nd; neither, 3rd; and S2 only, 4th. If one fails, the transmission protects itself like this:

S1 solenoidOnly 3rd and 4th in D
S2 solenoidOnly 2nd and 3rd
S1 and S2 solenoidsOnly 3rd, in D, 2 and L
Speed signal, turbine speed sensor (NT), fluid temperature sensor, SLT solenoid, coolant temperature, knock or throttle sensorNo 4th upshift (US Corolla manual)
SLU solenoidThe computer turns it off: no converter lockup

Toyota notes that even if you turn the engine off and back on in limp mode, the transmission stays in the same gear. So "stuck in 3rd" doesn't mean the transmission is done: read the codes first.

U340E and U341E trouble codes

P0705Shift lever position switch circuit (guide)
P0710, P0712 and P0713Fluid temperature sensor circuit; the sensor is part of the internal harness (guide)
P0711Implausible fluid temperature reading; Toyota replaces the internal harness
P0717No signal from the turbine speed sensor (NT): above 50 km/h (31 mph), under 300 rpm for 5 seconds (guide)
P0724Brake light switch circuit
P0751 and P0756Solenoid S1 or S2 doesn't do what the computer commands: the actual gear doesn't match the commanded one (guide)
P0973, P0974, P0976 and P0977S1 or S2 circuit shorted or open
P0787 and P0788ST (shift/timing) solenoid circuit shorted or open
P2714The SLT solenoid stays open and pressure drops; Toyota warns that if you keep driving, the clutch burns out
P2716SLT solenoid circuit (pressure control solenoid guide)
P2757 and P2759SLU converter solenoid: slip (engine speed 100 rpm or more above turbine speed with lock-up commanded) or its circuit
P0741, P2769 and P2770SL converter solenoid, on the versions that use it

Toyota says to handle any other code first, and warns that these can also set when clutches, brakes or gears inside the transmission are damaged. The 2009 US Corolla and the 2009 Yaris use the SLU solenoid (P2757 and P2759); Toyota's manual for the Corolla in other markets uses an SL (P0741, P2769 and P2770). We didn't confirm which one the Mexican Corolla has. Transmisiones Veinte 07 explains code P0741 (in Spanish), and you can look up others in our diagnosis by code.

Test values

These are the values in Toyota's service manuals for the 2009 Corolla (U341E) and the 2009 Yaris (U340E), with the fluid at 50 to 80 °C (122 to 176 °F):

Line pressure at idleD: 372 to 412 kPa (54 to 60 psi). R: 553 to 623 kPa (80 to 90 psi)
Line pressure at stallD: 1,120 to 1,230 kPa. R: 1,660 to 1,870 kPa (almost the same on the Yaris)
Stall speed in D2,410 ± 300 rpm on the Corolla 1.8; 1,850 to 2,450 rpm on the Yaris 1.5
Engagement delayUnder 1.2 s from N to D, and under 1.5 s from N to R
S1, S2 and ST solenoids11 to 15 Ω at 15 to 25 °C (Corolla)
SLT and SLU solenoids5.0 to 5.6 Ω at 20 °C (Corolla)
Turbine speed sensor (NT)560 to 680 Ω at 20 °C
Fluid temperature sensor2.5 to 4.5 kΩ at 25 °C; 0.22 to 0.28 kΩ at 110 °C

For the stall test, Toyota says to chock the wheels and not go past 5 seconds. If stall comes out 600 rpm or more below spec, suspect the converter; if it's high, low line pressure, the forward clutch, the No. 2 one-way clutch or a wrong fluid level. If pressure is high in every position, Toyota checks the SLT solenoid and the regulator valve; if it's low, the pump as well.

Which fluid does it take, and how is it checked?

Per Toyota in the US, the Corolla from 2009 and the Yaris from 2007 use Toyota ATF WS. Toyota warns that WS isn't compatible with T-IV or Dexron, and that other fluid can worsen shifts, make the locked-up converter shudder and, eventually, damage the transmission. We didn't confirm whether the 2006 Mexican Yaris already used WS.

Both units have a dipstick. Drive until the fluid is at 70 to 80 °C (158 to 176 °F), park on level ground and, with the engine idling and the brake on, move the lever through every position from P to L and back to P. Pull the dipstick, wipe it, push it all the way in and read the level in the HOT range. If it's low, add new fluid; if it's high, Toyota drains and refills. On the Yaris, a drain and refill takes 2.5 liters (2.6 US quarts).

How often should the fluid be changed?

In the 2009 US Yaris manual, Toyota says to change the fluid only when necessary, under severe operating conditions, and its WS bulletin calls for an inspection at 100,000 miles, with no changes in normal use. That doesn't mean the transmission is sealed for life: it has a dipstick and a level procedure. In Mexico we didn't find Toyota's maintenance table for these cars; Toyota México's warranty doesn't cover damage from fluids or additives the brand doesn't recommend.

U340E and U341E myths

  • "The 2014 Corolla is already a CVT." In Mexico, Toyota still listed it as "Automática de 4 velocidades" in October 2015; the CVT shows up on its site in August 2016.
  • "The U341E is in the 2003 to 2008 Corolla." Those Corollas and Matrixes use the A245E family; on the Corolla, the U341E starts in 2009.
  • "It has no dipstick; it's sealed for life." The 2009 Corolla and the 2009 Yaris have a dipstick, and Toyota gives the procedure to check the level hot.
  • "Any ATF or Dexron will do." Toyota says WS isn't compatible with T-IV or Dexron, and Toyota México's warranty doesn't cover damage from fluids or additives the brand doesn't recommend.
  • "If it sets a solenoid code, replace the solenoid and you're done." Toyota warns those codes also set when clutches, brakes or gears are damaged, and some end in the valve body or the transmission.
  • "It's stuck in 3rd: the transmission is done." It can be limp mode from a solenoid or a sensor; read the codes first.
  • "You can keep driving with P2714." Toyota warns that if you do, the clutch burns out and the car stops moving.
  • "The U340E and the U441E are the same unit." They're different transmissions; in the TSS catalog, only one axle seal fits both.

How is it diagnosed?

  • Check the fluid level and condition hot, with the dipstick.
  • Read the codes with a scan tool. Toyota handles any other code first and then the transmission codes.
  • If it's stuck in 3rd or won't take 4th, find the cause of limp mode: the S1 and S2 solenoids, and the sensors that block 4th.
  • Measure the solenoids: 11 to 15 Ω for the on/off ones and 5.0 to 5.6 Ω for the linear ones (Corolla).
  • With hot fluid, run the line pressure, stall and engagement delay tests.
  • Then come the valve body and the converter; the whole transmission comes last.

If the transmission, engine or computer is replaced, Toyota clears what was learned (RESET MEMORY) with its scan tool and runs a road test so the computer relearns. Its US bulletins also call for checking both alignment pins, flushing the cooler and lines with the correct ATF, using the correct converter bolts and washers, and adjusting the shift cable and the position switch. For leaks, see our transmission fluid leak guide; for the valve body, the valve body guide.

See U340E and U341E parts

TSS parts for the U340E and U341E

The U340E and U341E page has every TSS part for these units. These are the ones that match the jobs in this guide:

Fluid and filter changeU340E, U341E and U341F filter or filter with pan gasket
Damaged or leaking pan19-bolt pan
Transmission overhaulTSS Rojo U340E gasket kit
Axle seal leakRight axle seal and case-side axle seal

The TSS catalog has no solenoids, valve body, friction plates or converter for these units, and U441E parts are for a different transmission. The axle seals fit several Toyota units: confirm the size with your distributor. If you're torn between the Rojo and Dorado kits, read how they differ. For the Camry and RAV4 6-speed automatics, see our U660E and U760E guide.

TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • What transmission does the 2009 to 2016 Corolla have?

    In Mexico, the 1.8 automatic versions from 2009 to about 2016 have a 4-speed automatic: the U341E, per Toyota's US documents for the same engine. The XRS 2.4 has the U250E 5-speed, and from 2017 the Corolla is a CVT.

  • What transmission does the automatic Yaris have?

    The Yaris 1.5 from 2006 to about 2017 has a 4-speed automatic, probably the U340E, the unit named in the 2009 US Yaris manual. The 2016 to 2019 Yaris R uses a Mazda 6-speed, and the 2019-on Yaris a CVT.

  • What's the difference between the U340E and the U341E?

    They're the same 4-speed family: the U340E goes with the Yaris 1.5 engine and the U341E with the Corolla 1.8. The U341F is the all-wheel-drive version. We didn't find a Toyota document comparing their strength.

  • Why is my Corolla stuck in 3rd?

    It's usually limp mode: with an S1 solenoid fault the transmission only uses 3rd and 4th, and with S1 and S2, only 3rd. A fault in several sensors also blocks 4th. Read the codes before opening the transmission.

  • Which fluid does the U341E take?

    The 2009-on Corolla uses Toyota ATF WS, and Toyota warns it isn't compatible with T-IV or Dexron. It's checked hot with the dipstick, at 70 to 80 °C (158 to 176 °F).

  • How many liters does the Yaris U340E take?

    Per the 2009 US Yaris manual, a drain and refill takes 2.5 liters (2.6 US quarts). Then check the level hot with the dipstick.

  • What should the U341E stall speed be?

    Toyota gives 2,410 ± 300 rpm on the Corolla 1.8 and 1,850 to 2,450 rpm on the Yaris 1.5, with hot fluid and for no more than 5 seconds.

  • Is there a campaign or warranty for the U340E or U341E?

    We found no US recalls for these transmissions and no Toyota México campaigns for them.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.