Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

Toyota U660E and U760E problems: Camry, RAV4, Sienna

TSS editorial team · · 13 min read

Gloved technician examining an open automatic transmission valve body assembly on a steel bench for Toyota U660E and U760E
In short
  • The U660E (with the 3.5 V6) and U760E (with the 2.5 4-cylinder) are Toyota's 6-speed front-wheel-drive automatics: in Mexico, the 2007 to 2017 Camry, 2013 to 2018 RAV4, 2011 to 2016 Sienna and 2014 to 2016 Highlander.
  • Their most documented failure is a brief converter shudder at 40 to 80 km/h under light throttle, with no check light. For the 2012 to 2014 Camry 2.5, Toyota published a Mexico bulletin: a new converter, four pan magnets and software.
  • Toyota names its solenoids SL1 to SL4, SLT, SLU and SL. P0776 is SL2 and P0796 is SL3; one stuck solenoid can set several codes.
  • In limp mode, depending on the failed solenoid, the transmission holds 2nd, 3rd or 5th; with an input sensor fault, it only uses 1st and 3rd.
  • It takes ATF WS only and has no dipstick: the level is set hot, at 85 to 90 °C. Toyota Mexico calls for a change every 80,000 km in severe use.

The U660E and U760E are the 6-speed automatics Toyota uses with its 3.5 V6 and 2.5 4-cylinder: in Mexico, the 2007 to 2017 Camry, 2013 to 2018 RAV4, 2011 to 2016 Sienna and 2014 to 2016 Highlander. If yours shudders at 40 to 80 km/h, sticks in one gear or sets solenoid codes, here are the failures Toyota documented, including a Mexico bulletin, the codes, the test values from its service manual, how to check the fluid without a dipstick and the TSS parts. If you're not sure which transmission your Toyota has, start with our Toyota guide.

What are the U660E and U760E?

Toyota started building the U660E in January 2006: it was its first 6-speed front-wheel-drive automatic, with a compact single-axis gear train for 400 N·m, and it debuted in the Camry and the Lexus ES 350. In November 2008 came the U760E, which Toyota presents as part of the same series, for its 4-cylinder engines. The all-wheel-drive versions are called U660F and U760F.

Both use seven solenoids: SL1, SL2, SL3 and SL4 make the shifts (1st uses SL1; 2nd, SL1 and SL3; 3rd, SL1 and SL4; 4th, SL1 and SL2; 5th, SL2 and SL4; and 6th, SL2 and SL3), SLT controls line pressure, SLU the converter lock-up pressure, and the on/off SL the lock-up valve. The engine computer runs the U760E; the U660E has its own computer, mounted on the transaxle. This is how to tell them apart:

EngineU660E: 3.5 V6 (2GR-FE). U760E: 2.5 4-cylinder (2AR-FE), and the 2.7 (1AR-FE) on imported models
ComputerU660E: its own computer (TCM), mounted on the transaxle. U760E: run by the engine computer
All-wheel driveThe AWD versions are called U660F and U760F
Serial numberOn factory units, on top of the bell housing, toward the front; Toyota remanufactured units have it elsewhere
DipstickNone: the level is set hot through the overflow plug
Don't confuse withU151E and U250E (5-speeds), U241E (4-speed) and UA80E (8-speed, from 2018)

Which Toyotas have it in Mexico?

Camry 3.5 V6, 2007 to 2009"Automática de 6 velocidades secuenciales con Súper ECT-i": U660E (that era's Camry 2.4 is a 5-speed)
Camry 2.5 and 3.5 V6, 2010 to 2014"Automática de 6 velocidades secuenciales con ECT-i": U760E with the 2.5 (Toyota's Mexico bulletin names the U760) and U660E with the V6
Camry 2.5 and 3.5 V6, 2015 to 20176-speed automatic (we didn't re-check these spec sheets): by engine, U760E and U660E
RAV4 2.5, 2013 to 2018"Automática de 6 velocidades (con ECT-i)": U760E, and U760F on the AWD and 4WD versions
Highlander 3.5 V6, 2014 to 2016"Automática de 6 velocidades con ECT-i": U660E (U660F with all-wheel drive)
Sienna 3.5 V6, 2011 to 2016"Automática secuencial de 6 velocidades": U660E

Toyota Mexico only says "6-speed automatic"; the code comes from Toyota's tables by engine. Note: the Camry spec page on Toyota Mexico's site said "5 speeds" until 2012, but the 2010 and 2012 spec sheets say 6, and the Mexico bulletin names the U760. These aren't part of this family: the 2005 to 2009 Camry 2.4 and the 2004 to 2006 V6 (5-speeds), the 2009 to 2012 RAV4 (4- and 5-speeds), the 2008 to 2013 Highlander and 2004 to 2010 Sienna (5-speeds), and the 2018-on Camry (8-speed). The Venza, Avalon and Lexus ES 350 and RX 350 with these units weren't sold by Toyota Mexico: if you have one, it's an import.

U660E and U760E problems by symptom

Brief shudder at 40 to 80 km/h (25 to 50 mph) under light throttle, before a shift, no check lightThe converter in partial lock-up (U760E): 2012 to 2014 Camry 2.5 (Mexico bulletin) and 2013 to 2015 RAV4 (US). First check the fluid level and type
Shudder on a 2007 to 2009 Camry V6Converter shudder, per summaries of Toyota's US bulletins
Flares into 4th or on 6-4 or 5-4 downshiftsToyota published US bulletins on flares in the 2007 U660E, which we only know by their titles; according to the rebuilding industry, the molded C1 and C2 clutch pistons
Check light with P0746, P0776, P0796, P2808 or P2714A stuck solenoid, the valve body or an internal failure; one stuck solenoid can set several codes
Check light with P0748, P0778, P0798, P2810, P2716, P2769 or P2770The circuit: harness, connector, internal harness, the coil or the computer
Stuck in 2nd, 3rd or 5thLimp mode from a solenoid or sensor fault
Highway whine on a Camry 2.5Fluid level; on 2012 to 2014 cars, a modified shift cable (US)
Leaks from the panThe pan gasket (2013 to 2015 Camry, US)
The lever won't leave PNot the transmission: the brake light switch (US recall), a relay in cold weather or the shifter cover

Shudder at 40 to 80 km/h: Toyota's Mexico bulletin

This is the U760E's best-documented failure. In 2015, Toyota published bulletin T-SB-0045-15, addressed to the Mexican market, for the 2012 to 2014 Camry with the 2.5 and the U760E: a brief, intermittent shudder when driving under light load, at about 40 to 80 km/h (25 to 50 mph), most noticeable before an upshift. It's the converter in partial lock-up, and Toyota notes it doesn't turn on the check light or set a code.

The bulletin repair: a new converter; remove the pan, discard the 2 magnets and fit 4 new ones, wiping the pan with a clean cloth only, no chemicals; new pan and drain-plug gaskets; ATF WS; and a computer software update, since, according to Toyota, the computer shouldn't be replaced. The bulletin cites Toyota Mexico's basic warranty, 36 months or 60,000 km.

In the US, Toyota also ran a software-only campaign for the Camry and extended converter coverage on the 2012 to 2014 Camry and 2013 to 2015 RAV4 (U760E and U760F), with the same repair. Those programs don't apply in Mexico. On the U660E, summaries of US bulletins mention converter shudder on the 2007 to 2009 Camry, 2008 Avalon and ES 350. Before replacing the converter, check the level and that the fluid is ATF WS: according to the rebuilding industry, the wrong fluid also causes this shudder, and in manual 3rd the partial lock-up is disabled, which helps tell it apart from an engine misfire.

Stuck in one gear: limp mode

When a sensor or solenoid fails, the computer cuts power to the failed one and shifts with the rest. This is what Toyota's 2012 Camry service manuals say, the same for the U660E and U760E:

Input speed sensor or CAN networkOnly 1st or 3rd
Output sensor, fluid temperature sensor or knock sensorOnly 1st to 4th
Low voltage at the computerHolds 6th if it was in 6th; otherwise 5th
SL1 solenoid stuck offFixed in 3rd or 5th
SL2 solenoid stuck offFixed in 2nd or 3rd
SL3 solenoid stuck offFixed in 3rd
SL4 solenoid stuck offFixed in 2nd
Transmission connector unplugged (Toyota's U760E test)Only P, R and 3rd in D

If a solenoid sticks on, there's no limp mode: the transmission engages the wrong gear. And with the connector unplugged, Toyota runs a manual shift test: if the transmission then does P, R and 3rd without problems, the fault is electrical; if not, it's in the transmission. More on solenoids in our solenoid guide.

U660E and U760E trouble codes

These are the codes in Toyota's U760E service manual (2012 Camry 2.5), with their letter and solenoid:

P0746 and P0748SL1 solenoid, the "A": performance and electrical fault
P0776 and P0778SL2 solenoid, the "B", which works in 4th to 6th
P0796 and P0798SL3 solenoid, the "C", which works in 2nd and 6th
P2808 and P2810SL4 solenoid, the "G", which works in 3rd and 5th
P2714 and P2716SLT line pressure solenoid, the "D". P2714 monitors clutch slip
P2757 and P2759SLU converter lock-up pressure solenoid: engine speed 70 rpm or more above the turbine with lock-up commanded, or lock-up when not requested
P2769 and P2770SL lock-up solenoid: short or open circuit
P0705Range sensor: more than one position at a time
P0711, P0712 and P0713Fluid temperature sensor: won't warm up, shorted (150 °C or more) or open (−40 °C)
P0715 and P0717Input (turbine) speed sensor
P0791 and P0793Intermediate shaft speed sensor
U0100Lost communication with the engine computer

Toyota doesn't include P0731 to P0736 or P0894 in the U760E list: a wrong gear shows up as a solenoid "performance" code, and Toyota warns that one solenoid stuck off can set codes for several. With SLT stuck on (P2714), pressure drops, the engine revs freely and, if you keep driving, the clutches burn out. More in our guides to P0745 to P0748, P0776 and P0796, speed sensors, the temperature sensor, the range sensor and U0100, or in our diagnosis by code.

Test values

These come from Toyota's 2012 Camry service manual, with the fluid at 50 to 80 °C:

SL1, SLT and SLU solenoids5.0 to 5.6 Ω at 20 °C
SL (lock-up) solenoid11 to 15 Ω at 20 °C
U760E line pressure, in DIdle: 360 to 430 kPa. Stall: 1,160 to 1,350 kPa
U760E line pressure, in RIdle: 670 to 820 kPa. Stall: 1,650 to 1,910 kPa
U660E line pressure, in RIdle: 800 to 950 kPa. Stall: 1,900 to 2,200 kPa
Stall speedU760E: 2,730 rpm (+200 / −400). U660E: 2,680 rpm (+200 / −430). No more than 5 seconds
Engagement time lagN to D: under 1.2 seconds. N to R: under 1.5 seconds

According to Toyota, line pressure that's high in every range points to the SLT solenoid or the regulator valve; low in every range, to SLT, the regulator or the pump; low only in D, to a leak in that circuit or the C1 clutch; and low only in R, to a leak in that circuit or the B2 and B3 brakes. More in our valve body guide.

Which fluid does it take, and how do you check it without a dipstick?

Toyota ATF WS only: Toyota warns it isn't compatible with T-IV or Dexron, and the Mexican 2018 RAV4 manual says another fluid can cause poor shift quality, lock up the transmission, shudder and damage. There's no dipstick; the level is checked like this, according to Toyota's bulletin:

  • Warm the engine until the scan tool shows the fluid at 85 to 90 °C, with accessories off, and move the lever from P to D and back to P.
  • With the car level and the engine idling, remove the fill plug and then the overflow plug (the drain plug, with a 6 mm hex key).
  • If fluid flows out slowly and only drips, the level is correct; if nothing comes out, add ATF WS until it drips. Toyota sets its gauge to 75.5 or 72.0 mm on the U660E and to 71.0 or 69.0 mm on the U760E, depending on idle speed.
  • Torque the overflow plug to 40 N·m and the fill plug to 49 N·m, with new gaskets.

Toyota Mexico's 2018 RAV4 manual gives 6.5 liters as a reference capacity, and says to have the change done at the dealer; on the RAV4, the front differential shares the transmission's fluid.

How often should the fluid be changed?

In the US, Toyota says ATF WS is only inspected in normal use. Toyota Mexico is stricter: in the 2018 RAV4 manual it calls for an inspection every 40,000 km and, in severe use, a change every 80,000 km or 48 months. To Toyota Mexico, severe use means driving heavily loaded, long periods of idling or low speed, like taxis, police or delivery work, or more than 2 hours straight at high speed.

Other documented problems

In the US, Toyota fixed a highway whine on the 2012 to 2014 Camry 2.5 with a modified shift cable, and documented pan gasket leaks on the 2013 to 2015 Camry. And some failures look like the transmission but aren't: the US had a recall of the brake light switch on the 2009 Camry and 2009 to 2011 Venza that kept the lever from leaving P; a relay that failed in extreme cold; and another recall for the 2014 Sienna's shift cable. If your Toyota leaks, see our fluid leaks guide.

U660E and U760E myths

  • "There's a recall and Toyota fixes it for free." There was no recall: the US had a software campaign and warranty extensions, and in Mexico we found only bulletin T-SB-0045-15, under the basic warranty.
  • "ATF WS is lifetime fluid." In the US, Toyota only calls for inspection in normal use, but Toyota Mexico calls for a change every 80,000 km in severe use.
  • "It's checked with a dipstick, cold." It has no dipstick: the level is set hot, at 85 to 90 °C, through the overflow plug.
  • "Any ATF will do." ATF WS only; Toyota warns it isn't compatible with T-IV or Dexron.
  • "P0776 means replace solenoid B." It's a performance code: Toyota checks other codes, runs the active test, measures the solenoid and inspects the valve body before condemning the transmission.
  • "P2714 is just the pressure solenoid." Toyota uses it to monitor clutch slip; with SLT stuck on, it warns the clutches burn out.
  • "If it shudders at 60 km/h, replace the transmission." Toyota fixed it with software and, when it confirmed the condition, a new converter and extra magnets; it didn't replace transmissions.
  • "The U660E and U760E are the same transmission." The U760E is part of the same series, but with a different engine, computer and parts; some are shared.

How is it diagnosed?

  • Check the level hot through the overflow plug and confirm the fluid is ATF WS.
  • Read the codes and handle the others first: one stuck solenoid can set several codes.
  • Run the active test with the scan tool: compare the gear the computer commands with the gear you get.
  • Measure the solenoid (5.0 to 5.6 Ω at 20 °C on SL1, SLT and SLU) and test it through a 21 W bulb: the valve should move and click.
  • If the solenoid is fine, inspect the valve body for debris and valves that stick; then the transmission.
  • For shudder at 40 to 80 km/h with no codes, check the fluid and ask the dealer about software before replacing the converter.
  • After replacing the transmission, computer or valve body, reset the learned values (and on the U660E, enter the compensation code, if applicable).

See U660E and U760E parts

TSS parts for the U660E and U760E

The U660E and U760E page has every TSS part for these transmissions. These are the ones that match the jobs in this guide:

Fluid service and pan-off jobsU760E: 2008 to 2014 filter and pan gasket. U660E: filter and 18-bolt pan gasket
Solenoid codes, after Toyota's tests7-solenoid kit for the U660 and U760
Slipping or burnt C1 and C2 clutchesForward and direct friction plates, U760E friction plate pack and steel plates for the U660E or U760E
LeaksPump seal, left axle seal and right axle seal
PumpPump bushing for the 2007 to 2009 U660E or 2010-on U660E and U760E
Full rebuildU760E: Rojo overhaul kit without pistons. U660E: Rojo kit or 2007 to 2009 Dorado

TSS doesn't carry the U760E converter, the pan magnets or the valve body, which are the parts in Toyota's bulletin. Confirm with your distributor which filter fits your transmission by year, whether the solenoid kit fits yours, and which side each seal goes on. The difference between the Rojo and Dorado kits is in our guide to TSS overhaul kits.

TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • Which Toyotas have the U660E and which the U760E in Mexico?

    Toyota Mexico only says "6-speed automatic". By engine and Toyota's documents, the U760E goes with the 2.5 4-cylinder (2010 to 2017 Camry and 2013 to 2018 RAV4; U760F on all-wheel-drive RAV4s) and the U660E with the 3.5 V6 (2007 to 2017 Camry, 2011 to 2016 Sienna and 2014 to 2016 Highlander). The Venza, Avalon and Lexus ES and RX use them too, but Toyota Mexico didn't sell them.

  • Why does my Camry 2.5 or RAV4 shudder at 40 to 80 km/h?

    Toyota documented it as converter shudder in partial lock-up: brief, under light throttle, most noticeable before a shift and with no check light. For the 2012 to 2014 Camry with the U760E it published a Mexico bulletin (T-SB-0045-15): a new converter, four pan magnets, a gasket and a software update. Check the fluid level and type first.

  • Is there a campaign or extended warranty in Mexico?

    The US had a software campaign and extended warranties for the Camry and RAV4. In Mexico we found only bulletin T-SB-0045-15, covered by the basic 36-month or 60,000 km warranty. Check with Toyota Mexico using your VIN.

  • Which fluid does it take, and how often is it changed?

    ATF WS only; Toyota warns it isn't compatible with T-IV or Dexron. In the Mexican 2018 RAV4 manual it's inspected every 40,000 km, and in severe use (heavy loads, taxi or delivery work, long idling or more than 2 hours at high speed) it's changed every 80,000 km or 48 months.

  • How do you check the level without a dipstick?

    Hot: with the fluid at 85 to 90 °C (shown on the scan tool), the car level and the engine idling, remove the overflow plug; the level is right when the fluid only drips. Toyota sets its gauge to 75.5 or 72 mm on the U660E and 71 or 69 mm on the U760E, depending on idle speed.

  • What do P0776, P0796 or P2808 mean on these transmissions?

    That the computer doesn't see the gear it commanded: P0746 is the SL1 solenoid, P0776 SL2, P0796 SL3 and P2808 SL4; P2714 is SLT, the line pressure solenoid. Toyota checks other codes, runs the active test, measures the solenoid (5.0 to 5.6 Ω at 20 °C on SL1, SLT and SLU) and inspects the valve body before condemning the transmission. One stuck solenoid can set several codes.

  • Why is my Camry stuck in one gear?

    That's limp mode: if a solenoid fails, the computer switches it off and shifts with the others; depending on which one fails, the transmission holds 2nd, 3rd or 5th. With an input sensor or CAN network fault, it only uses 1st and 3rd.

  • Do the U660E and U760E use the same parts?

    Some do: in the TSS catalog they share the pump seal, the 2010-on pump bushing, the axle seals and a C1 and C2 clutch friction plate, and the 7-solenoid kit is listed for both. The filter, pan gasket, overhaul kits and steel plates differ. And the U660E has its own computer mounted on the transaxle. Confirm with your transmission code and year.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.