Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

Nissan RE4F04A and RE4F04B problems: Altima, X-Trail

TSS editorial team · · 9 min read

Exposed lower valve body housing draining red ATF fluid beneath a vehicle for RE4F04A and RE4F04B service
In short
  • The RE4F04A and RE4F04B are Nissan's front-wheel-drive 4-speed automatics, with their own computer and the same ratios.
  • In Mexico they're in the Altima 2.5 and 3.5, the X-Trail 2.5 and the Sentra 2.5 (RE4F04B), and the 2001 and 2002 Quest 3.3 (RE4F04A).
  • With a major electrical fault, the transmission stays in 3rd and the light flashes for about 8 seconds the next time you switch the ignition on.
  • Nissan gives a chart for what's slipping: in 2nd and 4th, the band; in 3rd and 4th, the high clutch; only in 1st, the low one-way clutch.
  • It takes Nissan Matic D, 8.5 to 9.4 liters depending on the model, and has a dipstick with COLD and HOT marks.

The RE4F04A and RE4F04B are the front-wheel-drive 4-speed automatics Nissan used in its larger cars and minivans in the nineties and early 2000s. In Mexico, Nissan Mexicana's spec sheets show them in the Altima 2.5 and 3.5, the Quest 3.3, the X-Trail 2.5 and the Sentra 2.5. This guide pulls together what Nissan's service manuals say: how to tell them apart, fail-safe, what slips by gear, the codes, test values, the fluid and TSS parts. If you don't know which transmission your car has, see which transmission does my Nissan have.

What are the RE4F04A and RE4F04B?

What it isA 4-speed front-wheel-drive automatic with its own computer (TCM) and five solenoids: shift A and B, overrun clutch, converter lockup and line pressure
RatiosThe same in both: 2.785, 1.545, 1.000 and 0.694; reverse 2.272
InsideReverse, high, forward and overrun clutches, a band, two one-way clutches and the low and reverse brake
RE4F04AIn Nissan's US manuals, the 2001 Altima 2.4 and the 2002 Quest 3.3
RE4F04BIn Nissan's US manuals, the 2002 Maxima 3.5, the 2002 to 2006 Altima 2.5 and the 2002 to 2004 Altima 3.5, the Sentra 2.5 and the 2005 Quest 3.5
How to tell them apartBy the model code on the transmission (80L02 or 80X77 on the A; 88X04, 85X21, 88X02, 85X63 or 89X01 on the B), by their solenoid resistances and because only the B has a turbine speed sensor
Don't confuse it withThe RE4F03 in the Tsuru, Versa, March and Sentra 1.8: smaller, with a 2.861 first gear and 7.0 liters of fluid
Other namesFord calls it the 4F20E in the Mercury Villager, the Quest's twin; Mazda used a very similar unit, the LJ4A-EL, in the Millenia
DipstickYes: the level is checked in P, with the engine idling, at the COLD or HOT marks

Which Nissans have them in Mexico?

Altima 2.5 and 3.5 (L31), 2002 to 2004 spec sheets"4AT con Overdrive … Electrónico", with the same ratios as the RE4F04B: the RE4F04B
Quest 3.3 (2001 and 2002)"Automática de 4 velocidades con overdrive y Shift interlock", with every RE4F04A ratio: the RE4F04A
X-Trail 2.5 (T30)"4 T/A con Overdrive": the same unit as the Altima 2.5 with that engine, the RE4F04B
Sentra 2.5 (B15, 165 hp)"Aut. de 4 vel. con overdrive": the RE4F04B; the SE-R was manual, and the 1.8 uses the RE4F03B
Quest 3.5 (2004)4-speed and 5-speed versions; the 4-speed is the RE4F04B. From 2006, 5-speed only
Murano and PathfinderNo: the Murano is a CVT, and the Pathfinder uses a rear-wheel-drive-based transmission

Nissan Mexicana doesn't print the transmission code: we infer it from Nissan's US manuals for the same engine and year, and on the Altima and Quest, from their ratios. The Mexican Altima page lists a reverse ratio that doesn't match Nissan's (2.272): don't use it. The 2007-on Altima and the 2008-on X-Trail are CVTs, with their own guide.

Fail-safe mode

According to Nissan, when a major electrical circuit fails, the computer puts the transmission in fail-safe: it always runs in 3rd, even with the lever in 1, 2 or D, and the car feels sluggish from a stop. The next time you switch the ignition on, the O/D OFF or A/T CHECK light flashes for about 8 seconds. Read the codes before replacing parts, and check the battery too: in the 2004 Altima self-diagnosis, Nissan includes low battery voltage.

Problems by symptom

This is Nissan's chart for the stall and road tests, plus what its US bulletins say:

Stuck in 3rd, sluggish from a stopFail-safe from an electrical fault: shift solenoid A or B, the throttle sensor or the speed sensors. Read the codes
Slips in 1st onlyThe low one-way clutch
Slips in 1st to 3rd, with no engine braking in 3 or 2The forward clutch or its one-way clutch
Slips in 3rd and 4thThe high clutch
Slips in 2nd and 4thThe band
Slips in reverse, with engine braking in 1The reverse clutch
Slips in reverse, without engine braking in 1The low and reverse brake
Won't go past 80 km/h (50 mph), or weak launch with a low stall speedThe converter's one-way clutch
Chirp on the 2-3 shift (1999 and 2000 Altima and Quest)In the US, Nissan traced it to the high clutch
Slow or late 1-2 and 2-3 shifts (2000 and 2001 Maxima)Nissan issued US bulletins for this symptom
Intermittent P0740 (2000 and 2001 Altima and Quest)A US Nissan bulletin for the converter solenoid
Ratio codes with an engine fault (2002 Altima and Sentra)In the US, Nissan found an engine fault can set transmission codes

Nissan doesn't replace the converter for mileage alone: it replaces it if it shudders or won't lock up after all hydraulic and electrical diagnosis. The exception is taxi, delivery and police cars, which wear the lockup lining.

Trouble codes

P0705Park/neutral position switch (range sensor) (guide)
P0710Fluid temperature sensor (guide)
P0720Output speed sensor; the check engine light comes on only if the vehicle speed sensor also fails (guide)
P0725Engine rpm signal
P0731, P0732, P0733 and P07341st, 2nd, 3rd or 4th gear function (guide)
P0740 and P0744Converter lockup solenoid and lockup function
P0745Line pressure solenoid (guide)
P0750 and P0755Shift solenoids A and B; they trigger fail-safe (guide)
P1705Throttle sensor for the transmission; it also triggers fail-safe
P1760Overrun clutch solenoid
U1000CAN communication (2004 Altima)

On the 2004 Altima, Nissan also reads faults without a scan tool: with a key, brake and lever sequence, the light flashes, and each long flash points to a part (the 1st, the output sensor; the 4th, solenoid A; the 5th, B; the 6th, the overrun solenoid, and the 7th, the converter solenoid). You can look up other codes in our diagnosis by code.

Test values

Shift A and B and overrun solenoids (RE4F04A)20 to 40 Ω
RE4F04B solenoidsShift A 20 to 30 Ω, shift B 5 to 20 Ω, overrun 20 to 30 Ω
Converter solenoid10 to 20 Ω on the A; 5 to 20 Ω on the B
Line pressure solenoid2.5 to 5 Ω on both
Output speed sensorA: 500 to 650 Ω. B: about 450 Hz at 20 km/h with a scan tool; Nissan says it can't be tested with a multimeter
Turbine speed sensor (B only)About 240 Hz at 20 km/h
Line pressure at idle500 kPa (73 psi) in D, 2 and 1; about 778 kPa (113 psi) in R
Stall speed2,350 to 2,800 rpm with the 2.5; 2,550 to 3,050 with the 3.5 V6; 2,800 to 3,100 with the 2.4; 1,900 to 2,200 with the 3.3 V6

These are values from Nissan's service manuals for the 2001 and 2004 Altima, the 2002 Quest and the 2002 Maxima (US). Nissan runs the pressure test with the fluid at 50–80 °C (122–176 °F). The fluid temperature sensor reads 1.5 V at 20 °C and 0.5 V at 80 °C.

Which fluid does it take, and how is it checked?

Nissan Matic D in every manual for these units we checked. The 2004 Altima manual says Dexron III/Mercon may also be used, and in 2008 Nissan issued a bulletin with a special fluid requirement for its 2004-and-newer cars: use the one your manual calls for. Ford calls for MERCON in the Villager's 4F20E.

It holds 8.5 to 9.4 liters in total, depending on the model. Removing the drain plug only drains part of it: Nissan refills the same amount that came out, idles the engine for 5 minutes, checks it and, if the fluid is still dirty, repeats the change.

It has a dipstick in the filler tube: Nissan checks the level in P with the engine idling, first at the COLD mark (30 to 50 °C) and, after about 5 minutes of driving, at the HOT mark (50 to 80 °C), without overfilling. Dark fluid with a burnt smell means worn frictions; milky pink means water in the transmission.

If the fluid has friction or band material in it, Nissan replaces the radiator and flushes the cooler lines after the repair; on any repair it inspects and cleans the radiator's cooler. More in our cooler and fluid leak guides.

RE4F04 myths

  • "The RE4F04 is a 4WD unit." The Altima, Quest, Maxima and Villager are front-wheel drive, and Nissan describes it as a front-wheel-drive transaxle.
  • "The RE4F04B takes MERCON." Nissan calls for Matic D in every manual for this unit we checked.
  • "The Murano and Pathfinder have the RE4F04." The Murano is a CVT, and the Pathfinder uses a rear-wheel-drive-based transmission.
  • "The RE4F04A and RE4F04B use the same solenoids." Nissan gives different resistances for each, and TSS sells different sets.
  • "The converter is replaced by mileage." Nissan replaces it only after full diagnosis, except on taxis, delivery and police cars, which wear its lining.
  • "If it's stuck in 3rd, the transmission is burned." It's fail-safe from an electrical fault: read the codes.
  • "A fluid change drains it all." A drain only removes part of it; Nissan repeats the change if the fluid is still dirty.

How is it diagnosed?

  • Check the fluid level and condition in P, with the engine idling, at the COLD or HOT mark.
  • Read the codes; if it's stuck in 3rd, start with the solenoid and sensor circuits.
  • Measure the solenoids against the values for your letter (A or B).
  • Run the line pressure test with the fluid at 50–80 °C (122–176 °F), then the stall test, with one minute at idle between positions.
  • Use Nissan's chart to tell what's slipping by gear and engine braking.
  • After a repair, clean the radiator's cooler.

See RE4F04A and RE4F04B parts

TSS parts for the RE4F04A and RE4F04B

The RE4F04A and RE4F04B page has every TSS part for these units. These are the ones that match the jobs in this guide:

Fluid and filter changeAltima RE4F04A or 1997-on RE4F04A filter, 2002-on RE4F04B filter, and Farpak pan gasket
Slips in 2nd and 4thBand
Slips in 3rd and 4th21-tooth or 24-tooth high clutch friction plates; on the RE4F04B, the high clutch piston and piston cover
Slips in 1st to 3rdForward clutch friction plates
No engine brakingOverrun clutch friction plates
Slips in reverseRE4F04A or RE4F04B reverse clutch friction plates
Solenoids (RE4F04A)Single O-ring 5-solenoid set
Transmission overhaulRojo gasket kit, steel plates, pump bushing and pump O-ring
LeaksPump seal and left and right axle seals
Converter (after diagnosis)Altima 2.4 converter

The TSS RE4F04B solenoid set, low and reverse friction plates and Dorado kit are out of stock for now. The Rojo kit, the Altima filter and other parts say RE4F04A in their titles: confirm with Veinte 07 that they fit your RE4F04B. If you're torn between gasket kits, read how they differ.

TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • Which transmission does the 2002 to 2006 Nissan Altima have?

    A 4-speed automatic, the RE4F04B, with the 2.5 engine, and with the 3.5 through 2004, according to Nissan's manuals; the Mexican spec sheet lists its same ratios. In the US, the 2005 and 2006 3.5 used a 5-speed.

  • Which transmission does the 2003 to 2007 X-Trail have?

    The X-Trail 2.5's 4-speed automatic is the same unit as that era's Altima 2.5, the RE4F04B.

  • What's the difference between the RE4F04A and the RE4F04B?

    They have the same ratios, but the B has a turbine speed sensor, a different output sensor and solenoids with different resistances. The model code on the transmission tells them apart.

  • Why is my Altima stuck in third?

    It's Nissan's fail-safe: with a major electrical fault, the transmission always runs in 3rd, and the light flashes for about 8 seconds the next time you switch the ignition on. Read the codes.

  • Which fluid does the RE4F04B take?

    Nissan Matic D, according to Nissan's manuals. The 2004 Altima manual says Dexron III/Mercon may also be used; use the one your manual calls for.

  • How many liters does the RE4F04 hold?

    8.5 to 9.4 liters in total, depending on the model. A drain only removes part of it, so Nissan repeats the change if the fluid is still dirty.

  • Is the RE4F04 the same transmission as the Tsuru's or the Versa's?

    No: those use the RE4F03, which is smaller, with other ratios and 7 liters of fluid.

  • Is there a campaign for the Altima's transmission?

    We found no recalls for internal failures of this unit. In the US, Nissan issued bulletins for a chirp on the 2-3 shift and for an intermittent P0740 on the 2000 and 2001 Altima and Quest.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.