Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

Toyota A750E and A750F problems: Tacoma, FJ Cruiser

TSS editorial team · · 11 min read

Close-up of automatic transmission fluid draining from a pan plug during service on Toyota A750E and A750F
In short
  • The A750E and A750F are Toyota's 5-speed rear-drive automatic: the E is 2WD and the F, 4WD. They go with the 4.0 V6 and the 4.7 V8.
  • In Mexico they're in the Tacoma V6 through 2015, the 2008 to 2014 FJ Cruiser, the 2003 to 2007 4Runner, the Land Cruiser 4.7, the 2007 and 2009 Tundra and the 2008 Sequoia.
  • If it's stuck in one gear, it's usually limp mode: with an S1 fault it starts in 3rd, and with SR, SL1 or SL2 there's no 5th.
  • Toyota checks other codes first, then the solenoids, the valve body, the converter and, last, the transmission; several clunks and whines that seem to be the transmission come from the driveshaft or the differential.
  • It takes Toyota ATF WS and has no dipstick: the level is set through the overflow plug at 36 to 46 °C.

The A750E and A750F are the 5-speed automatic in Toyota's 4.0 V6 and 4.7 V8 trucks: the Tacoma, FJ Cruiser, 4Runner, Tundra, Sequoia and Land Cruiser. In Spanish there's almost nothing on them beyond sales listings. This guide pulls together what Toyota's service manual and bulletins say: which trucks have it in Mexico, what fails by symptom, limp mode, the codes, test values, the fluid and TSS parts. If you don't know which transmission your truck has, see which transmission does my Toyota have.

What are the A750E and A750F?

What it isA Toyota 5-speed rear-drive automatic with electronic control (ECT)
A750E or A750FThe A750E is the 2WD unit; the A750F, the 4WD unit, with the transfer case bolted behind it
Engines4.0 V6 (1GR-FE) and 4.7 V8 (2UZ-FE)
ComputerIt has none of its own: the engine computer runs it
SolenoidsSeven: S1, S2 and SR, on/off; SL1, SL2 and SLT, linear pressure solenoids; and SLU, for the converter
Serial numberStamped on the left rear of the case, above the pan
DipstickNone on the 2005-on Tacoma: the level is set through the overflow plug at 36 to 46 °C (97 to 115 °F)
Don't confuse withA340 (4-speed, US Tacoma 2.7), AB60 (6-speed, 5.7 V8), A760 (6-speed, 4.6 V8) and AC60 (2016-on Tacoma)

Suzuki used the same family in the 2007 to 2009 Grand Vitara V6, under the Aisin TB-50LS name: the gear ratios Suzuki publishes are the same. We cover it in our Suzuki guide.

Which Toyotas have it in Mexico?

Tacoma 4.0 V6, 2005 or 2006 to 2015"Automática de 5 velocidades con ECT-i": A750E on 2WD trucks and A750F on 4WD. The 2009 spec sheet only lists 2WD versions; 2011 and 2013 to 2015 list 2WD and 4WD
FJ Cruiser 2008 to 2014"Automática de 5 velocidades con ECT-i", part-time 4WD: A750F
4Runner 4.7 V8 2003 to 2007, and 4.0 V6 2006 and 2007"Automática de 5 velocidades": A750E or A750F
Land Cruiser 4.7, 2004 to 2007"Automática de 5 velocidades con ECT", 4WD: A750F
Tundra 2007 (4.0 and 4.7) and 2009 Tundra CrewMax 4.7"Automática (secuencial) de 5 velocidades con ECT-i": A750E on 2WD and A750F on 4WD
Sequoia 4.7, 2008"Automática de 5 velocidades con ECT-i": A750E or A750F
Tacoma 2016 on, Tundra and Sequoia 5.7 and Land Cruiser 2010 onNo: they're 6-speeds (AC60 and AB60)
HiluxNo: in Mexico the gasoline Hilux is manual, and the automatic is the 2.8 diesel 6-speed

Toyota México never publishes the transmission code: we infer it from Toyota's US tables for the same engine, drive and years. Lexus didn't sell the GX 470 in Mexico; the ones on the road are imports.

A750E and A750F problems by symptom

This is the symptom table in Toyota's service manual (US 2008 Tacoma), in its order. Toyota checks the electrical side before the mechanical one:

Won't move in any forward position or in reverseShift cable, manual valve, parking lock pawl, rear planetary and converter clutch
No reverseValve body, C3 clutch, B4 brake and F1 one-way clutch
No 4-5 upshiftElectrical first (lever switch, engine coolant temperature sensor, NT sensor and SL1, SL2 and SR solenoids); then the valve body, B1 brake and C1 clutch
Harsh engagement into DSL1 solenoid, valve body, C1 accumulator and clutch, and F3 one-way clutch
Harsh engagement into RSLT and SLU solenoids, valve body, C3 accumulator and clutch, B4 brake and F1
Harsh shifts in every gear, or shift points too high or too lowSLT and SL1 solenoids and the valve body
Slips or shudders forward and in reverse once warmValve body, oil strainer (filter), F1, C3 and converter clutch
No converter lockup, or the engine stalls when starting off or stoppingSLU solenoid, valve body and converter clutch
The fluid temperature light won't go offNo. 2 fluid temperature sensor, engine coolant temperature sensor and computer
Delayed R or D engagement with code P0705 (2005 to 2009 Tacoma)In a US bulletin, Toyota found liquid or corrosion in a connector at the left-side junction block, and replaced the harness, not the transmission

Before blaming the transmission, Toyota's US bulletins rule out three problems that get mistaken for it: the rear clunk when braking or starting off (the driveshaft, on the Tacoma and FJ Cruiser), the whine at 80 to 97 km/h, or 50 to 60 mph (the rear differential), and the vibration at 25 to 40 km/h, or 15 to 25 mph, when accelerating (the driveshaft). And it's normal for it not to shift into 5th with a cold engine: Toyota blocks 5th below 55 °C (131 °F) and 51 km/h (32 mph), and 4th below 47 °C (117 °F) and 49 km/h (30 mph).

Stuck in one gear: limp mode

S1 solenoidIn D it starts in 3rd and goes to 4th and 5th: no 1st or 2nd
S2 solenoidIn D it uses 1st and then 4th and 5th
SR solenoid1st to 4th, no 5th
SL1 or SL2 solenoid, or No. 1 fluid temperature sensorNo 5th upshift
SLT solenoidHarsher shifts: it loses fine line pressure control
SLU solenoidNo converter lockup; fuel economy drops
Transmission connector unplugged (Toyota test)D and 4: 4th; 3: 3rd; 2 and L: 1st; R and P work

Toyota notes that even if you turn the engine off and back on in limp mode, the transmission stays in the same gear. So if it starts in 3rd or 4th, check the S1 and S2 solenoids and their circuit first; if there's no 5th, SR, SL1, SL2 or the fluid temperature sensor.

A750E and A750F trouble codes

P0705Shift lever position switch: it sends more than one signal at a time (guide)
P0710 to P0713No. 1 fluid temperature sensor, part of the internal harness (guide)
P0717 and P0722No signal from the input (NT) or output (SP2) speed sensor; Toyota first checks the sensor is tightened properly (guide)
P0746 and P0748SL1 solenoid: performance or circuit
P0751, P0756 and P0771Solenoids S1, S2 or SR don't do what the computer commands (guide)
P0776 and P0778SL2 solenoid: performance or circuit (guide)
P0781The 1-2 shift valve in the valve body is stuck
P0894 and P2714A clutch is slipping; Toyota warns that if you keep driving, the clutch burns out and the truck stops moving
P0973 to P0986S1, S2 and SR solenoid circuits shorted or open
P2716SLT solenoid circuit
P2740 to P2743No. 2 fluid temperature sensor, the one for the warning light
P2757 and P2759SLU converter solenoid: slip or circuit. This unit doesn't use P0741
P2772Transfer case 4L switch (4WD)

Toyota says to handle any other code first, and warns that these can also set when clutches, brakes or gears inside the transmission are damaged. You can look up other codes in our diagnosis by code.

Test values

Stall speed in D and R2,250 to 2,550 rpm
Engagement delayUnder 1.2 s from N to D, and under 1.5 s from N to R
Line pressure at idleD: 363 to 423 kPa (53 to 61 psi). R: 484 to 564 kPa (70 to 82 psi)
S1, S2 and SR solenoids11 to 15 Ω at 20 °C
SL1, SL2, SLT and SLU solenoids5.0 to 5.6 Ω at 20 °C
NT and SP2 speed sensors560 to 680 Ω at 20 °C
Fluid temperature sensors79 Ω to 156 kΩ, depending on temperature

These are the values in Toyota's service manual for the US 2008 Tacoma 4WD, with the fluid at 50 to 80 °C (122 to 176 °F). Other versions can differ, and the same manual prints another, slightly different pressure table, so use your truck's. For the stall test, don't go past 5 seconds. If stall comes out 600 rpm or more below spec, suspect the converter; if it's high, low line pressure, the C1 clutch, the F3 one-way clutch or the fluid level. If pressure is high in every position, Toyota checks the SLT solenoid and the regulator valve; if it's low, the pump as well.

Which fluid does it take, and how is it checked?

Per Toyota in the US, the A750 uses Toyota ATF WS: the 4Runner and Land Cruiser from 2004, the Tacoma, Tundra and Sequoia from 2005, and the 2007 to 2014 FJ Cruiser. The 2003 units, like that year's Land Cruiser, used T-IV. Toyota warns WS isn't compatible with T-IV or Dexron. The 4WD Tacoma's transfer case doesn't take ATF but 75W-90 gear oil.

The 2005-on Tacoma has no dipstick. The level is set through the overflow plug with the engine idling and the fluid at 36 to 46 °C (97 to 115 °F); with the scan tool, Toyota puts the computer in temperature detection mode, and on 4WD trucks the A/T OIL TEMP light comes on at 36 °C and blinks above 46 °C. If no fluid comes out of the overflow, add 0.4 liters and repeat. A pan drop takes about 1.3 liters back; a valve body removal, 3.9; and a converter or transmission replacement, 5.3 before setting the level.

Toyota in the US says to change the fluid only when necessary, under severe use, and its WS bulletin calls for an inspection at 100,000 miles. Toyota also notes the fluid runs hotter when towing, climbing hills and in traffic; check the cooler in our cooler guide.

Documented leaks

In its US bulletins, Toyota documented leaks from the A750E rear seal (2WD, 2005 and 2006), from the yoke plug on the 2009 and 2010 Tacoma, and from the transfer case input seal on the 2013 to 2015 4Runner, at the seam between the transmission and the transfer case. More in our transmission fluid leak guide.

A750E and A750F myths

  • "It's checked with a dipstick." The 2005-on Tacoma has none: the level is set through the overflow plug, hot, between 36 and 46 °C (97 and 115 °F).
  • "You can use Dexron or T-IV." From 2004 or 2005, depending on the model, it uses ATF WS, and Toyota says it isn't compatible with T-IV or Dexron.
  • "If it sets P0705, the transmission is bad." On the 2005 to 2009 Tacoma, Toyota found corrosion in a connector and replaced the harness.
  • "The clunk from the rear when braking or starting off is the transmission." On the Tacoma and FJ Cruiser, Toyota fixed it at the driveshaft.
  • "If it slips, you can keep driving." Toyota warns the clutch burns out and the truck stops moving.
  • "It won't shift into 5th when cold: it's failing." That's normal: Toyota blocks 5th with the engine below 55 °C (131 °F) and under 51 km/h (32 mph).
  • "The converter code is P0741." On the A750 it's P2757, or P2759 for the circuit, for the SLU solenoid.
  • "The transfer case takes the same ATF." On the 4WD Tacoma it takes 75W-90 gear oil.
  • "Swap the transmission and you're done." Toyota clears the learned values (Reset Memory) after replacing the transmission, engine or computer, and calls for flushing the cooler and lines with the correct ATF.

How is it diagnosed?

  • Check the level through the overflow plug, at the right temperature, and the fluid condition.
  • Read the codes. Toyota handles any other code first and then the transmission codes.
  • If it's stuck in one gear, identify the limp mode with the table above and check that solenoid or its circuit.
  • Measure the solenoids: 11 to 15 Ω for the on/off ones and 5.0 to 5.6 Ω for the linear ones; with 12 V they should move and click.
  • With hot fluid, run the stall, engagement delay and line pressure tests.
  • With the transmission connector unplugged, test the fixed gears: if it also fails that way, the problem is inside the transmission.
  • Then come the valve body and the converter; the whole transmission comes last.

If the transmission, engine or computer is replaced, Toyota clears the learned values with its scan tool and runs a road test; on 4WD trucks it also sets up the fluid temperature light again. Its US bulletins call for flushing the cooler and lines with the correct ATF, checking the alignment pins, using the correct converter bolts (the black one goes first) and adjusting the shift cable and the position switch.

See A750E and A750F parts

TSS parts for the A750E and A750F

The A750E and A750F page has every TSS part for these units. These are the ones that match the jobs in this guide:

Fluid and filter changeA750E and A750F filter and pan gasket
Transmission overhaulRojo and Dorado gasket kits
Slips or shudders (clutches)Friction plates and steel plates
Direct clutchBonded balance piston
Leak at the bell housingPump seal

Both gasket kits are listed for the A750E: confirm with your distributor that they fit your A750F. The TSS catalog has no solenoids, valve body, sensors or converter for this unit. If you're torn between the Rojo and Dorado kits, read how they differ, and for the Camry and RAV4 6-speed automatics, see our U660E and U760E guide.

TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • What transmission does the 2005 to 2015 Tacoma have?

    In Mexico, that era's Tacoma 4.0 V6 has the A750 5-speed automatic: the A750E on 2WD trucks and the A750F on 4WD, per Toyota's US documents. From 2016 it's a 6-speed.

  • What's the difference between the A750E and the A750F?

    The A750E is the 2WD unit and the A750F the 4WD unit, with the transfer case bolted behind it. The A750E has an extension housing with its rear seal in that spot.

  • Why won't my Tacoma shift into 5th?

    With a cold engine that's normal: Toyota blocks 5th below 55 °C (131 °F) and 51 km/h (32 mph). If it happens hot, it can be limp mode from the SR, SL1 or SL2 solenoids or the fluid temperature sensor; read the codes.

  • Does the A750 have a dipstick?

    Not on the 2005-on Tacoma. The level is set through the overflow plug, with the engine idling and the fluid at 36 to 46 °C (97 to 115 °F).

  • Which fluid does the A750 take?

    Toyota ATF WS from 2004 or 2005, depending on the model; the 2003 units used T-IV. Toyota warns WS isn't compatible with T-IV or Dexron.

  • What should the A750 stall speed be?

    On the 2008 Tacoma 4WD, Toyota gives 2,250 to 2,550 rpm, with hot fluid and for no more than 5 seconds.

  • What does code P0705 mean on a Tacoma?

    That the shift lever position switch is sending more than one signal at a time. On the 2005 to 2009 Tacoma, Toyota found corrosion in a junction block connector and replaced the harness, not the transmission.

  • Is there a campaign or warranty for the A750?

    We found no US recalls for this transmission and no Toyota bulletins addressed to Mexico.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.