Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

722.6 / NAG1 transmission problems: stuck in 2nd, leaks

TSS editorial team · · 20 min read

Disassembled longitudinal automatic transmission housing, clutch drum and open valve body on a rebuild bench for 722.6 and NAG1
In short
  • The 722.6 is Mercedes-Benz's 5-speed automatic; Chrysler calls it the NAG1 or W5A580 and used it in the 300C, Charger, Challenger, Grand Cherokee V6, Durango 3.6 and Wrangler 3.6.
  • In limp mode it doesn't always hold 3rd: it keeps the gear it was in and, after a restart, only 2nd and reverse work. With P0730, P1731, P1704 or P1705, the computer puts it in neutral.
  • The most documented leak is the 13-pin connector (its O-rings), not the pan gasket, and shudder under light acceleration usually comes from water in the fluid.
  • Chrysler gives 2.5 to 6.5 Ω for the shift and pressure solenoids, 2.0 to 4.0 Ω for the converter solenoid and a 5 V square wave for the speed sensors. There's no output speed sensor.
  • Chrysler, Dodge and Jeep units take ATF+4 and Mercedes-Benz units MB 236.14; a pan and filter change takes about 5 liters, and the adaptives must be reset after a repair.

The 722.6 is Mercedes-Benz's 5-speed automatic: in 2000 and 2001, Mercedes-Benz Mexico offered it across almost its whole automatic lineup, from the C-Class to the G-Class. Chrysler calls it the NAG1 or W5A580 and put it in the 300C, Charger, Challenger, Grand Cherokee V6, Durango 3.6 and Wrangler 3.6, among others. If yours is stuck in 2nd, leaks at the connector, shudders or drops into neutral, here are the failures Mercedes-Benz and Chrysler documented, the codes it sets, its test values, the fluid it takes and the TSS parts that fit it. If you're not sure which transmission your vehicle has, start with our Dodge, Jeep, RAM and Chrysler guide.

What is the 722.6 (NAG1) transmission?

It's a 5-speed automatic for rear-wheel drive and 4x4, designed by Mercedes-Benz. Mercedes calls it the 722.6 (or 5G-Tronic) and Chrysler the NAG1, for "New Automatic Gearbox, generation 1"; within that family, Chrysler uses the names W5A300, W5A380 and W5A580: the W stands for the torque converter, the 5 for the speeds, the A for automatic and the number is the maximum input torque in N·m. Daimler's Sprinter documents say "NAG1 722.6", and Chrysler's sales code is DGJ.

Inside it has three planetary gear sets, three clutches (K1, K2 and K3), three multi-plate brakes (B1, B2 and B3) and two freewheels (F1 and F2). The transmission computer is mounted outside (Chrysler calls it the EGS-52) and shifts with six solenoids on the valve body: three shift solenoids, two pressure solenoids and one for the converter. The conductor plate links those solenoids to the round 13-pin connector and carries the speed and temperature sensors.

This is how to tell it apart:

Speeds5 forward; rear-wheel drive or 4x4. The 722.9 (7G-TRONIC) has 7
ConnectorRound, 13 pins, near the front right corner of the pan, with a bayonet lock
W5A580 ratios3.59, 2.19, 1.41, 1.00 and 0.83; reverse 3.16
Speed sensorsTwo Hall-effect sensors on the valve body (N2 and N3); no output speed sensor
Transmission computerMounted outside the transmission; on the 722.9 it's built into the valve body
DipstickMost have no owner dipstick; the 2005 Grand Cherokee does
Chrysler sales codeDGJ; the 545RFE is DGQ

Which cars and SUVs have the 722.6 or NAG1 in Mexico?

At Chrysler, Dodge and Jeep it's the 5-speed automatic of their rear-wheel-drive cars and several V6 SUVs. Chrysler Mexico's spec sheets rarely name the transmission; we confirmed the name with Chrysler's bulletins and manuals:

2005 Chrysler 300C 5.7"Automática 5-Vel con autostick": the W5A580, according to Chrysler's bulletins for that model
Chrysler 300, Dodge Charger and Challenger V8 (5.7, 6.1 and 6.4), 2008 to 20145-speed automatic with manual shift mode: the W5A580
Charger, Challenger and 300 3.6 V6, 2011 to 2014The 5-speed versions (2011 Charger, 2013 Charger SXT and Challenger SXT up to 2014) have the W5A580; the 8-speed ones, a different transmission
2004 Chrysler Crossfire 3.2"Automática 5 Velocidades": the Mercedes-Benz transmission
Jeep Grand Cherokee 3.7 V6, 2005 to 2010The W5A580; with the 4.7 and 5.7 V8s, the 545RFE
Grand Cherokee 3.6 V6 and SRT8 6.4, 2011 to 2013The W5A580; with the 5.7 V8, the 545RFE in 2011 and a 6-speed from 2012
Dodge Durango 3.6 V6, 2011 and 2012The W5A580; the 5.7 V8 has the 545RFE
Dodge Nitro R/T 4.0, 2008 to 20115-speed automatic, probably the W5A580; the Nitro 3.7 has the 42RLE
Jeep Wrangler 3.6, 2012 to 2016"Automática 5 Velocidades": the W5A580; the 2007 to 2011 Wrangler 3.8 has the 4-speed 42RLE

Chrysler's other rear-wheel-drive 5-speed automatic, the 545RFE, goes with the 4.7 and 5.7 V8s in the Grand Cherokee, Durango, Commander and Ram. The 2008 and 2009 300 and Charger 3.5 and the Nitro 3.7 aren't NAG1s either: they have the 4-speed 42RLE. From 2014 in the Grand Cherokee and Durango, and from 2015 or 2016 in the V8 cars, Chrysler moved to 8-speed transmissions. Diesel versions sold in other markets use a diesel variant, the W5J400.

At Mercedes-Benz, the 722.6 was the automatic in almost the whole lineup until the 7-speed 7G-TRONIC (722.9) arrived. Mercedes-Benz Mexico doesn't print "722.6" on its spec sheets, but given the 5 speeds and the dates, this is the transmission:

C-Class (C 200 K, C 230 K, C 240, C 280, C 320 and the AMG C 32 and C 43), CLK 320 and 430 and E 55 AMG, 2001"Cambio automático de 5 marchas con cambio secuencial" (5-speed automatic with sequential shifting)
S 430, S 500 L, S 600, CL 500, SL 500 and 600, SLK 230 K and 32 AMG, ML 320 and 430 and G 500, 2000 and 2001"Transmisión automática 5 velocidades" (5-speed automatic)
S 55 AMG and SL 55 AMG (2006), S 600 L (2007), CL 600 and G 55 AMG (2008)5-speed automatic ("AMG SPEEDSHIFT" 5-speed on the AMGs)
2009 Sprinter Cargo Van 315 CDI"Transmisión automática opcional de 5 Velocidades" (optional 5-speed automatic)
C 280, C 350 and E 500 (2006), GL 450 and R 500 L7G-TRONIC: that's the 7-speed 722.9, not the 722.6

In the US, Daimler still wrote "NAG1 722.6" in documents for Sprinters built in 2017 and 2018. If your vehicle came used from the United States, confirm the transmission with the VIN: there were versions there that weren't sold in Mexico.

Common 722.6 and NAG1 problems by symptom

This table combines Chrysler's service manual and the bulletins Chrysler and Mercedes-Benz published in the US:

Stuck in 2nd and reverse, or in the gear it was inLimp mode: the computer switched off the solenoids because of a fault. Read its codes: solenoids, speed sensors, temperature sensor and Park/Neutral contact, voltage or the computer itself
Drops into neutral while drivingThe computer does it on purpose with P0730, P1731, P1704 and P1705. Also 3-4 valves stuck by debris in the valve body, or very fine metal in the fluid
Shudder or buzz under light acceleration on the highwayThe converter clutch, especially with water in the fluid (P0741). Check the fill tube seal
Drips at the front right corner of the panThe O-rings of the 13-pin connector's guide bushing, not the pan gasket. Check for fluid inside the connector
Harsh, delayed or "hanging" shifts when hotThe computer's calibration, adaptives not reset after a repair, low or contaminated fluid, or the valve body
Ratio code (P0730 to P0735) and the transmission feels fineTire size or axle ratio programmed wrong, a wheel that slipped or an ABS fault; then internal slip
The scan tool shows an odd temperature in P or NNormal on the NAG1: the temperature sensor is wired in series with the Park/Neutral contact and only reads in R or D. In P or N, Chrysler's scan tool shows engine temperature
No start and every shifter letter lit after a computer swapThe "Initialize EGS-52" procedure is missing, with P0602, P0700 or P1644
Slow to move for the first seconds after days parkedAccording to Chrysler Mexico, that's normal: the converter partly drains and refills in about 5 seconds

Stuck in 2nd: limp mode

According to Chrysler's service manual, when the computer detects a serious fault it switches off every solenoid: the transmission holds the gear it was in, with pressure at maximum and the converter unlocked, until the car stops. If you then shift to P, turn the engine off for at least 10 seconds and restart, D only gives 2nd, and R gives reverse. It stays that way until the fault is fixed and the code is cleared; a sporadic fault clears by turning the car off and on. Chrysler Mexico's 2012 Durango manual describes the same for the 3.6 V6: the transmission "se mantendrá en el rango de velocidad actual" (holds its current gear) until the vehicle stops, and then only P, R, N and second work.

Some codes send it to neutral on purpose: with P0730 and P1731 (incorrect ratio or gear), the computer puts the transmission in neutral until the car slows below 29 km/h, and it does the same with P1704 and P1705 (input sensor overspeed). That's how Chrysler describes the NAG1; since the Mercedes-Benz 722.6 is the same transmission, its limp mode also leaves 2nd and reverse.

To find out why it went into limp mode, read the transmission computer's codes. The causes Chrysler lists are the solenoids, the speed sensors (P0717, P2767 and P2784), the temperature sensor and the Park/Neutral contact (P0710 to P0714), voltage and the computer itself. On the Sprinter, Daimler documented a US case of limp mode from low voltage at the shifter module. Also check for fluid inside the 13-pin connector, as explained below. More on the computer in our guide to the transmission control module.

Fluid leak at the 13-pin connector

This is the failure with the most bulletins. From 1999 to 2008, Mercedes-Benz published several US bulletins for "all passenger models with 722.6" that lose fluid at the transmission's electrical connection, and Chrysler published 21-002-05 for the 2005 300 and Grand Cherokee and the 2004 and 2005 Crossfire and Sprinter.

The fluid shows up at the front right corner of the pan. The round 13-pin connector enters the case through a guide bushing with two O-rings, and those O-rings are what fail. Chrysler's fix: release the connector's bayonet lock, remove the bronze bolt in the center of the bushing, replace both O-rings (they're different sizes) and torque the bolt to 2.5 N·m; on the 2004 Sprinter it replaced the whole bushing. And it warns in capital letters: if the fluid comes from above the pan gasket, don't replace the gasket.

According to the rebuilding industry, the fluid can also wick up inside the harness to the transmission computer; that's why, when they replace the conductor plate, they replace the connector too. If your transmission leaks somewhere else, see our guide to transmission fluid leaks.

Shudder or buzz: water in the fluid and the converter

In the US, Chrysler published bulletin 21-011-05 for the NAG1 in its 2005 and 2006 5.7 cars and the 2005 Grand Cherokee 3.7: a shudder most noticeable when the converter clutch partly applies in 3rd and 4th, which shows up with as little as 0.5 % water in the fluid. The fix is to center the fill tube, seal its base, flush the transmission three times with ATF+4, running through every gear and reverse, and fit a new filter; the pan gasket can be reused.

In 2006, bulletin 21-003-06 pointed to the fill tube seal, which can let water in, with a high-pitched buzz under light acceleration. Chrysler air-tests it at 14 kPa (never above 34), replaces the seal, flushes the transmission and, if the shudder remains, replaces the converter. For code P0741, Chrysler's manual points to the lock-up control valve, the converter solenoid, the valve body or the converter. According to the rebuilding industry, this shudder is usually felt between 55 and 80 km/h.

Condensation was also behind a recall of 2005 Grand Cherokees (see below). What to do when the fluid has water in it, in our guide to burnt fluid, debris or water; and if the transmission runs hot, check the fluid cooler as well.

Harsh or delayed shifts: calibration and adaptives

Between 2004 and 2015, Chrysler published about 15 NAG1 computer reflashes in the US: for shudder during shifts, 4-3-4 shifts, garage shifts, a 1-2 upshift shudder, P0730 and P0731 from momentary wheel slip on slippery roads (2007 and 2008 Grand Cherokee 3.7), the check engine light with limp mode and P0730, and shifts that "hang" when towing above 32 °C. Before reflashing, Chrysler says to check the fluid level and condition.

This transmission learns: the computer adjusts the pressure of each shift with use. Chrysler requires resetting those adaptives (Reset Adaptives) after replacing the computer or the transmission, replacing clutch plates or seals and replacing or repairing the valve body. And after replacing or reflashing the transmission computer, the engine computer or the front control module (FCM), the "Initialize EGS-52" procedure is required; without it, the car may not start, every shifter letter (PRNDL) lights up and P0602, P0700 or P1644 set.

Drops into neutral or shifts poorly: the valve body

Chrysler explains that debris can get in through the vents on top of the valve body and stick the 3-4 valves (the shift pressure and holding valves): shifts flare, bump, feel harsh or the transmission drops into neutral. Fine and very fine metal particles in the fluid cause the same. For P0730, its manual names as usual causes a stuck solenoid, debris in the valve body, broken springs, leaking clutch seals and a dislodged or broken snap ring. In the US, Chrysler sold the replacement valve body with its filter and gasket. More in our valve body guide.

If the car won't move, Chrysler air-tests the B1, K3 and B2 clutches. With a lot of debris, it checks the front annulus gear and the input shaft, and the pump, whose rotor can break its inner lugs. And after a failure with a lot of metal or clutch material in the fluid, it says to replace the converter.

The conductor plate and the speed sensors

The conductor plate is the plastic plate that sits on the valve body, inside the pan. It carries the two input speed sensors (N2 and N3, Hall effect), the fluid temperature sensor and the Park/Neutral contact, and connects the solenoids to the 13-pin connector. According to Chrysler, apart from the solenoids, all its electrical components are fixed to the plate's tracks, so in practice it's replaced as a unit.

Its failures set P0717, P2767 or P2784 (speed sensors), P1704 or P1705 (the transmission drops to neutral) and P0710 to P0714 (temperature), with erratic shifts or limp mode. Before replacing it, Chrysler says to check the sensors' supply, signal and ground at the connector, and to scope their 5 V square wave in 2nd. According to the rebuilding industry, deposits in the fluid can make the sensors fail.

Since the NAG1 has no output speed sensor, the computer calculates output speed from the ABS wheel speed sensors. That's why an ABS fault, a slipping wheel or a tire size and axle ratio programmed wrong can set ratio codes. More on these codes in our guides to speed sensors and incorrect ratio.

722.6 and NAG1 trouble codes

These are the codes Chrysler's service manual lists for the NAG1 in the 2008 Grand Cherokee 3.7:

P0700Engine computer notice: a code is stored in the transmission computer. Read that one
P0710, P0712 and P0714Fluid temperature sensor: circuit, low voltage (under 0.5 V) or a reading that jumps suddenly
P0717 and P2767Input speed sensor 1 (N2) or 2 (N3) no signal: 0 rpm with the engine above 450 rpm and the wheels turning
P2784The N2 and N3 sensors disagree: more than 150 rpm apart in 2nd, 3rd or 4th
P1704 and P1705N2 or N3 sensor overspeed: the computer puts the transmission in neutral
P0730 and P1731Incorrect ratio or gear: the transmission goes to neutral until the car slows below 29 km/h
P0731 to P0735Ratio error in 1st, 2nd, 3rd, 4th or 5th
P0741, P0742 and P0743Converter clutch: slips, stays engaged or its solenoid has an electrical fault
P0748 and P0778Modulating pressure solenoid and shift pressure solenoid: electrical fault
P0752 and P0753, P0757 and P0758, P0762 and P0763Shift solenoids 1-2 and 4-5, 2-3 and 3-4. Each one only works during its shift
P2783Converter temperature too high: the computer calculates the converter clutch's heat
P0602 and P1644, with P0700A computer replaced without the "Initialize EGS-52" procedure
U0100, U0121, U0141, U0155 and other U codesNetwork codes: one computer isn't receiving another's messages

Three clarifications. The NAG1 doesn't set P0715, P0720 or P0722, because it has no output speed sensor. P0850 is the engine computer's Park/Neutral switch code, and P0928, P0930, P0931, P2775 and P2779 belong to the shifter (its brake interlock and the AutoStick buttons), not the transmission. And Mercedes-Benz computers store their own fault numbers. Look up any other code in our diagnosis by code, and the details in our guides to pressure solenoids, shift solenoids, the temperature sensor and lost communication.

Test values

These values come from Chrysler's service manual (2008 Grand Cherokee 3.7), measured from the transmission computer's connector:

Shift solenoids (1-2 and 4-5, 2-3 and 3-4) and both pressure solenoids2.5 to 6.5 Ω
Converter clutch solenoid2.0 to 4.0 Ω
Temperature sensor with the Park/Neutral contact, lever in D500 to 2,500 Ω; in P or N the circuit is open by design
N2 and N3 speed sensors (Hall effect)5 V square wave on a scope, in 2nd
Modulating pressure solenoidAlways active, at a 25 to 75 % duty cycle
Pan bolts and connector bushing bolt8 N·m and 2.5 N·m

If a value is out of range, check the harness and the 13-pin connector first, before replacing parts: if the connector has fluid inside, clean it and fix the leak.

Which fluid does the 722.6 take, and how much?

The fluid depends on who built the vehicle, not on the transmission's name:

  • Chrysler, Dodge and Jeep: ATF+4. Chrysler Mexico's 2012 Durango manual calls for ATF+4 or a fluid approved as ATF+4, and warns that another fluid can worsen shifts and cause converter shudder.
  • Mercedes-Benz: a fluid approved under specification MB 236.14, according to its fluid list for the 722.6.
  • Sprinter and Crossfire: even when Chrysler sold them, they take a Mercedes-type fluid Chrysler specified separately, not ATF+4. Chrysler warns that a non-approved fluid can cause shift problems and premature clutch wear.
  • A pan and filter change takes about 5.0 liters; dry, the transmission holds about 7.7, plus whatever the cooler and lines change.
  • No chemical flushes or additives: Chrysler says its transmissions don't need periodic flushing, only after a failure, contamination or overheating, and with the correct fluid.

How do you check the level without a dipstick?

Most have no owner dipstick. Chrysler Mexico says so in the 2012 Durango manual: regular fluid level checks aren't required, "por ello no hay varilla medidora" (so there's no dipstick). On Mercedes models, the fill tube cap has a locking pin that's replaced with a new one every time it's opened. The exception is the 2005 Grand Cherokee, which did have a dipstick. In the shop, the level is checked like this:

  • On level ground, with the engine running in P, after moving the lever through every position.
  • With a special dipstick that goes down the fill tube to the pan (Chrysler tool 9336; on the Sprinter, 8863B).
  • With the fluid temperature on the scan tool, which is only real with the lever in R or D.
  • Comparing the height and temperature with the maker's chart: Mercedes-Benz gives one range at 25 °C and another at 80 °C, and warns that both too little and too much fluid cause faults and damage.

On the NAG1, Chrysler's scan tool shows engine temperature in P or N, not transmission temperature, because the transmission sensor is wired in series with the Park/Neutral contact. That's why the reading is taken in R or D.

How often should the fluid be changed?

It isn't "sealed for life". According to the US schedule for the 2008 Grand Cherokee 3.7, Chrysler says to change fluid and filter every 192,000 km in normal use and every 96,000 km in severe use: police, taxi, fleet, off-road or frequent towing. On the Sprinter, every 96,000 km. Chrysler Mexico's 2012 Durango manual says to change them if you regularly tow for more than 45 minutes at a time. If your use looks like those cases, follow the severe schedule; on a Mercedes-Benz, your model's maintenance plan.

US recalls

We found no recalls or bulletins that name Mexico. In the US, these two involve this transmission:

  • 2005 (05V396): about 101,900 2005 Grand Cherokees with the 3.7 V6 and the NAG1. Condensation could get in through the fill tube seal; as it boiled, the transmission shuddered and overheated and, in the worst case, could start an underhood fire.
  • 2013 (13V-234): about 180,100 2012 and 2013 automatic Wranglers with the 3.6. The power steering line could wear a hole in the transmission cooler line; once the fluid is lost, the transmission stops working.

If your vehicle came from the US, check its VIN for open recalls.

722.6 and NAG1 myths

  • "In limp mode it always holds 3rd." It holds the gear it was in until the car stops; after shutting off and restarting, D only gives 2nd. The one that holds 3rd is the 545RFE with the 5.7 V8, according to the same Chrysler Mexico manual.
  • "It's sealed for life." Chrysler says to change fluid and filter every 192,000 km in normal use and every 96,000 km in severe use.
  • "The drip on the right side is the pan gasket." If the fluid comes from above the gasket, it's the 13-pin connector. Chrysler says it in capital letters in its bulletin: don't replace the pan gasket for that leak.
  • "A chemical flush will fix it." Chrysler doesn't recommend chemicals or periodic flushes; with water in the fluid, its bulletin says to flush it three times with the correct fluid and change the filter.
  • "Every NAG1 takes the same Mercedes fluid." Chrysler, Dodge and Jeep units take ATF+4; only the Sprinter and the Crossfire take the Mercedes-type fluid.
  • "The 722.6 and the 722.9 are the same." The 722.9 (7G-TRONIC) has 7 speeds and takes a different fluid and filter, with the computer built in. Codes 2767 and 2768 in Mercedes-Benz bulletins belong to the 722.9.
  • "Swap the computer and you're done." Chrysler requires the "Initialize EGS-52" procedure and an adaptives reset; without them, the car may not start.
  • "P0700 means the transmission is bad." It's only a notice from the engine computer: the code that matters is in the transmission computer.

How is it diagnosed?

  • Check the fluid level and condition the way the maker says (see above). If it looks milky or smells burnt, see what each case means in our guide to burnt fluid, debris or water.
  • Read the codes with a scan tool that reaches the transmission computer: P0700 in the engine computer is only a notice. Chrysler points out that a generic scan tool may not communicate with the NAG1 computer.
  • If it's stuck in 2nd, check battery voltage, the grounds and the 13-pin connector, in case there's fluid inside it. Then measure the solenoids and sensors from the computer connector, with the values in the table.
  • With a ratio code (P0730 to P0735), first check the ABS codes, that the tires are the original size and that the tire size and axle ratio are programmed correctly; then the valve body and the clutches.
  • If it shudders under light acceleration, look for water in the fluid and check the fill tube seal before replacing the converter.
  • After any repair, reset the adaptives with the scan tool (Reset Adaptives).

See 722.6 parts

TSS parts for the 722.6 and NAG1

The 722.6 and its variants page has every TSS part for this transmission. These are the ones that match the failures in this guide:

Leak at the 13-pin connector13-pin connector with 2 O-rings
P0717, P2767, P2784, P1704, P1705 or P0710 to P0714 on a Mercedes-Benz 722.6 (conductor plate)Conductor plate with connector, filter and pan gasket or conductor plate alone, round bayonet hole
Fluid serviceFilter and pan gasket
Pump seal leak or converter replacementPump seal
Full rebuildRojo overhaul kit or Dorado (H-D)

Both conductor plates are for Mercedes-Benz 722.6 units: TSS labels the kit "Solo Mercedes" (Mercedes only) and doesn't list them for Chrysler, Dodge or Jeep. The plate alone varies with the bayonet hole (round or U-shaped), so check yours. The 13-pin connector is listed for both makes. To confirm that the filter, gasket or overhaul kit fits your transmission, ask your distributor with the make, model and year. The difference between the Rojo and Dorado kits is in our guide to TSS overhaul kits.

TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • Which vehicles have the 722.6 or NAG1 transmission in Mexico?

    From Chrysler, Dodge and Jeep: the 300C, Charger and Challenger V8 up to 2014 and their 5-speed 3.6 versions, the Grand Cherokee V6 (3.7 from 2005 to 2010; 3.6 and SRT8 6.4 from 2011 to 2013), the 2011 and 2012 Durango 3.6, very probably the Nitro R/T 4.0, the 2012 to 2016 Wrangler 3.6 and the Crossfire. From Mercedes-Benz: every automatic in 2000 and 2001, then the V12 and supercharged AMG models; the 2009 Sprinter offered it as an option.

  • Are the NAG1 and the 722.6 the same transmission?

    Yes, it's the same 5-speed family: Mercedes-Benz calls it the 722.6 and Chrysler the NAG1 or W5A580 (sales code DGJ); Daimler writes "NAG1 722.6" in its Sprinter documents. What changes is the fluid each maker specifies, the calibration and some parts, such as the conductor plate.

  • Why is my 722.6 or NAG1 stuck in second gear?

    That's its limp mode: with a serious fault, the computer switches off the solenoids and the transmission holds the gear it was in; after you stop, turn the engine off for 10 seconds and restart, D only gives 2nd, plus reverse. Read the transmission computer's codes: solenoids, speed sensors (P0717, P2767, P2784), temperature, voltage or the computer itself.

  • Why does fluid drip near the transmission connector?

    From the two O-rings of the 13-pin connector's guide bushing, at the front right corner of the pan. Mercedes-Benz and Chrysler published US bulletins for this leak, and Chrysler warns not to replace the pan gasket for it. According to the rebuilding industry, the fluid can wick up the harness to the transmission computer.

  • What is the conductor plate and what are the symptoms when it fails?

    It's the plastic plate on the valve body that carries the N2 and N3 speed sensors, the temperature sensor and the Park/Neutral contact, and connects the solenoids. When it fails it sets P0717, P2767, P2784, P1704 or P1705 (drops to neutral) or P0710 to P0714, with erratic shifts or limp mode. Before replacing it, check the connector, the harness and the sensors' 5 V signal.

  • Which fluid does the 722.6 take, and how many liters?

    It depends on the make: Chrysler, Dodge and Jeep units take ATF+4; Mercedes-Benz units, a fluid approved under MB 236.14; and the Sprinter and Crossfire, the Mercedes-type fluid Chrysler specified. A pan and filter change takes about 5 liters; dry, about 7.7. Don't use chemical flushes.

  • How do you check the level without a dipstick?

    In the shop: on level ground, engine running in P, with a special dipstick down the fill tube and the fluid temperature on the scan tool, which is only real in R or D. The height is compared with the maker's chart for that temperature. The 2005 Grand Cherokee is the exception: it did have a dipstick.

  • What do P0730 and P1731 mean, and why does it go into neutral?

    The computer sees a ratio it didn't command and puts the transmission in neutral until the car slows below 29 km/h. Chrysler first checks the ABS codes and that the tire size and axle ratio are programmed correctly; then the fluid, debris in the valve body, springs, clutch seals and snap rings.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.