Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

RE5R05A transmission problems: stuck in 4th, pink fluid

TSS editorial team · · · 17 min read

Technician inspecting automatic transmission pan drain fluid beneath a vehicle while diagnosing the RE5R05A
In short
  • The RE5R05A is Nissan's 5-speed automatic for rear-wheel drive and 4x4. In Mexico it came in the 2005 to 2012 Pathfinder, the automatic Frontier 4.0 V6, the Titan and Armada 5.6 V8 and the automatic 350Z.
  • The most documented problem, in the US, is coolant getting into the transmission through a crack in the fluid cooler inside the radiator of 2005 to 2010 Frontier, Pathfinder and Xterra trucks: the fluid comes out pink or milky.
  • In limp mode it doesn't hold 3rd: depending on the fault, it holds 2nd, 4th or 5th. A fault in the input, direct or HLR clutch solenoids leaves it in 4th.
  • The computer sits on the valve body: Nissan replaces both together, and the new one comes blank and is programmed with its scan tool.
  • It takes Matic S (or Matic J), about 10.3 liters in the V6 and 10.6 in the V8, and it's checked with its dipstick. In Mexico, Nissan says to change the fluid every 40,000 km if you tow or drive on rough roads.

The RE5R05A is the 5-speed automatic Nissan used in its rear-wheel-drive and 4x4 trucks: in Mexico, the 2005 to 2012 Pathfinder, the automatic Frontier 4.0 V6, the Titan, the Armada and the 350Z. If yours is stuck in 4th, slips, bangs into D or has pink fluid, here are the failures Nissan documented, its limp mode, the codes with their test values, the fluid it takes and the TSS parts that fit it. For other models, see our guide to which transmission your Nissan has.

What is the RE5R05A transmission?

It's a 5-speed automatic for longitudinal engines, with rear-wheel drive or 4x4. According to the rebuilding industry, it first appeared in the 2002 Infiniti Q45; in the US, Nissan used it up to the 2015 Titan and Armada, the 2016 NV vans and the 2019 Frontier, before moving to 7- and 9-speed transmissions.

Each gear comes from combining three clutches (input, direct and HLR, for high, low and reverse), a band (the front brake), the forward, reverse and low coast brakes and two one-way clutches. The computer controls each clutch with its own solenoid, which is why Nissan names the codes by clutch rather than "shift solenoid A or B". This is how to tell it apart:

Speeds5 forward, for rear-wheel drive and 4x4
Ratios4.0 V6: 3.842, 2.353, 1.529, 1.000 and 0.839 (reverse 2.765). 5.6 V8: 3.827, 2.368, 1.520, 1.000 and 0.834 (reverse 2.613). The 350Z starts in a 3.540 first gear
Transmission computerMounted on the valve body, and Nissan sells them together; only the first Infinitis had it separate
Case connector10 pins (2016 Frontier)
DipstickYes, held by a bolt, with COLD and HOT ranges
Pan22 self-sealing bolts, with the drain plug at the rear
Model code on the ID plate (not the VIN)The seventh character "N" means the 5-speed automatic (2016 Frontier, 2012 Pathfinder and 2009 Armada)

Which trucks have the RE5R05A in Mexico?

Nissan Mexicana used it in five models. Its pages and spec sheets say "5-speed automatic", and Nissan's service manuals name the RE5R05A for the Mexican versions of the 2012 Pathfinder, 2009 Armada and 2016 Frontier:

Pathfinder R51 4.0 V6, 2005 to 2012"5 velocidades automática" (5-speed automatic); the 2012 service manual names the RE5R05A for the Mexican versions
Frontier D40 4.0 V6 automatic: SE V6 (2008), SV V6 and PRO-4X (2011), S and PRO-4X (2016)"5 velocidades automática con sobremarcha" (5-speed automatic with overdrive); the 2016 manual lists the Mexican S and PRO-4X, 2WD and 4WD, with the 5-speed automatic
Titan 5.6 V8, 2005 to 2014"Automática de 5 velocidades con Overdrive"; in its last years, with a tow mode
Armada 5.6 V8, 2005 to 2014"Automática de 5 velocidades con Overdrive"; the 2009 manual names the RE5R05A for the Mexican Armada SE
350Z, 2003 to 2008"Automática de 5 velocidades con modo manual" (5-speed automatic with manual mode), optional; the other choice was a 6-speed manual

These don't have this transmission: the 2000 to 2004 Frontier (D22), a 4-speed; the 2013 to 2020 Pathfinder, a CVT, or the 2023-on model, a 9-speed; the NP300 Frontier (D23), manual in 2016 and a 7-speed from 2017; the Frontier V6 PRO-4X from 2022, a 9-speed; and the 370Z, a 7-speed. The Xterra, the NV vans, the automatic Frontier 2.5 and the Infinitis with this unit (G35, FX, M and QX56, among others) weren't sold new in Mexico: if you have one, it's an import.

Common RE5R05A problems by symptom

This table combines the symptom chart in the 2016 Frontier service manual and the bulletins Nissan published in the US:

Pink or milky fluid, or the coolant level dropsWater or coolant in the fluid. On 2005 to 2010 Frontier, Pathfinder and Xterra trucks, Nissan documented in the US cracks in the fluid cooler inside the radiator
Stuck in 4th, no shiftsLimp mode from a fault in the input, direct or HLR clutch solenoid (P1752, P1762, P1767). Check the connector pins and the computer's power supply
Stuck in 5thThe front brake (band) solenoid stuck on (P1757)
Starts off and stays in 2ndInterlock fault (P1730): the harness, the low coast brake solenoid or a pressure switch
No 5thA speed sensor fault (the computer blocks 5th), the O/D OFF switch, the front brake band or the input clutch
No engine braking when you lift offThe low coast brake solenoid (P1772 or P1774), or P1731
Slips or flares between shiftsP0731 to P0735: the solenoids, that gear's clutch or the hydraulic circuit. According to the industry, also the input shaft sealing rings
Harsh engagement into DIdle speed, the engine or throttle signals, fluid temperature, the front brake solenoid, the fluid level, line pressure or the valve body; then the forward brake
Harsh 1-2 shiftThe throttle sensor, the direct clutch solenoid, the fluid or the valve body; then the direct clutch and, according to the industry, wear in its support
Shudder with the converter locked, or no lock-upThe fluid, speed signals, converter solenoid and valve body; then the converter or the pump (P0740, P0744)
No drive in D or no reverseFluid level and condition, line pressure, range sensor, shift cable and valve body; then the converter, pump, one-way clutches or brakes
Rolls in PThe range sensor, the cable or the parking pawl (in the US, a recall on the 2015 Armada)

Pink fluid: the cooler inside the radiator

This is the most documented problem on these trucks. On the Frontier, Pathfinder and Xterra, the transmission fluid is cooled in a tank inside the engine radiator. In the US, Nissan acknowledged that an internal crack in the fluid cooler tube inside the radiator can let coolant into the transmission, and extended the radiator warranty there on all 2005 to 2010 automatic Frontier, Pathfinder and Xterra trucks, including transmission damage. Nissan said the extension doesn't apply to other models, and the court settlement that came with it covered only the US and its territories.

NHTSA, the US road safety agency, reviewed a petition to investigate the issue from 2012 to 2016. It counted 2,505 complaints, 638 of them safety-related (the truck couldn't hold its speed, lost drive or stalled), and its lab found fatigue cracks at the cooler's fluid port. Owners described delayed shifts, slipping, jerking and poor acceleration, and many had to replace both the radiator and the transmission. NHTSA denied the petition in 2016.

What to do, according to Nissan's service manual: if the fluid is milky or cloudy, it has water in it; change it and find where it gets in. If it also carries clutch material, replace the radiator and flush the cooler lines. According to the rebuilding industry, coolant attacks the piston seals (especially the direct clutch's), the solenoid terminals and the computer, so shops fit a new radiator with any transmission repair. More in our guides to the fluid cooler and burnt fluid, debris or water.

Stuck in 4th, 5th or 2nd: limp mode

When the computer detects a fault, it fixes the transmission in 2nd, 4th or 5th, depending on where the fault is, with line pressure at maximum or the converter unlocked. The service manuals for the 2005 Pathfinder and the 2016 Frontier say so in the same words:

Input, direct or HLR clutch solenoidHolds 4th
Front brake (band) solenoid5th if stuck on; 4th if stuck off
InterlockHolds 2nd; the scan tool may show an input sensor fault that isn't real
Line pressure solenoidSwitched off: line pressure goes to maximum
Converter solenoidNo converter lock-up
Low coast brake solenoidNo engine braking in 1st and 2nd
Output speed sensor or input speed sensor 1 or 2No 5th
Range sensorHolds D; no start, no back-up lamp and no position indicator

Nissan points out that hard braking with the wheels spinning can trigger limp mode even with good circuits; in that case, the transmission returns to normal after turning the engine off for 10 seconds. If the fault comes back, read the codes. More on solenoids in our solenoid guide.

The valve body with the computer

On the RE5R05A, the transmission computer is mounted on the valve body, inside the pan, along with the input speed sensors and the fluid temperature sensor; Nissan calls it the "control valve with TCM" and sells it all as one part. Only the first Infinitis, like the 2003 G35, had a separate computer.

For solenoid and input sensor codes, Nissan first checks the scan tool data, the computer's power and ground, and the case connector pins for damage or looseness; if all of that is fine, it replaces the valve body with its computer. In 2010 it published a special US diagnostic flow chart for several of these codes on the RE5R05A.

Watch out: Nissan's new valve body comes with a blank computer. The vehicle's data must be written with Nissan's scan tool (CONSULT), with the key ON, the lever in P, the engine off and the fluid at 72 °C or less; if the old computer can be read, Nissan says to save its data first. For 2005 to 2008 V6 Frontier, Pathfinder and Xterra trucks with a dealer remanufactured transmission whose computer couldn't be read, Nissan replaced the whole valve body, with the pan gasket, the drain plug washer and the 22 pan bolts. Rebuilding shops, on the other hand, do replace individual solenoids. More in our guides to the valve body and the transmission control module.

Slipping, harsh shifts or no converter lock-up

Nissan warns that incorrect ratio codes (P0731 to P0735) aren't always electrical: a stuck valve in the valve body or a slipping clutch also sets them. Each gear uses different clutches: if it slips in 2nd, check the direct clutch; in 3rd, the HLR; in 4th, the input, HLR and direct clutches; and in 5th, the front brake band, the input clutch and the HLR. More in our incorrect ratio guide.

According to the rebuilding industry, worn ring grooves in the direct clutch support leave a harsh 1-2 shift even after a rebuild with a new valve body, and worn input shaft sealing rings cause flares with P0734 and P0735. That's why shops air-test those parts on every rebuild.

For the converter, Nissan separates two codes: P0740, an electrical fault in the converter solenoid, and P0744, no lock-up even with a good circuit, for example from a stuck valve. If it shudders with the converter locked, its symptom chart checks the fluid, the speed signals, the solenoid and the valve body before the converter.

Fluid leaks

  • The cooler lines: Nissan published US bulletins for leaks at the auxiliary cooler line on 2004 and 2005 Titans and Armadas, and at the left transmission-to-radiator hose on 2010 to 2013 Titans and Armadas, replaced along with both of its clamps.
  • The pan: it has 22 self-sealing bolts at 7.9 N·m, and Nissan says to replace them every time it comes off.
  • The pump seal, at the front, between the transmission and the engine.

A leak lowers the level, and with low fluid the transmission slips and overheats. How to find the source, in our guide to transmission fluid leaks.

RE5R05A trouble codes

These are the codes in Nissan's list for the 2016 Frontier, with the number of O/D OFF lamp flashes in parentheses. Early years use some different numbers, such as P1716 instead of P0717:

P0720 (1)Output speed sensor
P1762 (2)Direct clutch solenoid; on early units, also P1764 (function)
P0740 and P0744 (3)Converter: P0740 is an electrical fault in its solenoid; P0744, no lock-up even with a good circuit, for example from a stuck valve (P0744 guide)
P0745 (4)Line pressure solenoid
P1752 (5)Input clutch solenoid; on early units, also P1754
P1757 (6)Front brake (band) solenoid; on early units, also P1759
P1772 and P1774 (7)Low coast brake solenoid: circuit and function
P1767 (8)HLR (high, low and reverse) clutch solenoid; on early units, also P1769
P0705 (9)Range sensor (Park/Neutral switch)
P0710 or P1710 (10)Fluid temperature sensor
P0717 (11)Input (turbine) speed sensor; on early units it was P1716
P1730 (12)Interlock: the transmission holds 2nd
P1731 (13)1st gear engine braking
P0615 (14)Starter relay
P1705 (15)Throttle sensor signal
P0725 (16)Engine speed signal
U1000 (17) or U0100CAN network communication with the engine computer
P0731 to P0735 (18 to 22)Incorrect ratio in 1st, 2nd, 3rd, 4th or 5th: an electrical fault, a stuck valve or a slipping clutch

The flashes come from the no-scan-tool self-diagnosis described in the 2016 Frontier service manual: after a sequence of key, lever, brake and throttle steps, the O/D OFF lamp flashes according to the stored fault. P0894, P0715 and the P0750 to P0770 shift solenoid codes aren't in Nissan's lists for this transmission: Nissan names each solenoid after its clutch, P1752 to P1774. Look up any other code in our diagnosis by code, and the details in our guides to the pressure solenoid, speed sensors, the range sensor, the temperature sensor and lost communication.

Test values

These values come from Nissan's service manual; most are for the 2016 Frontier with the 4.0 V6. They change by year, so use your year's manual:

Case connector (10 pins, 2016 Frontier)Pins 1 and 2: battery voltage at all times; 6: with the key ON; 5 and 10: ground; 3 and 8: CAN network; 7: 0 V in R (back-up lamp); 9: battery voltage in P and N (starter)
Fluid temperature sensorAbout 15 kΩ (3.3 V) at 0 °C, 6.5 kΩ (2.7 V) at 20 °C and 0.9 kΩ (0.9 V) at 80 °C
Input speed sensors 1 and 21.3 kHz: sensor 1 at 50 km/h in 4th, and sensor 2 at 20 km/h in 1st
Output speed sensor185 Hz at 20 km/h
Solenoid current, on the scan toolInput, direct and HLR clutches: 0.6 to 0.8 A released and near 0 applied; front brake: 0.6 to 0.8 A applied; converter: 0.4 to 0.6 A locked
Stall speed4.0 V6: 2,600 to 2,900 rpm (2016 Frontier); 2005 Pathfinder: 2,200 to 2,500
Line pressure, 4.0 V6 (2016 Frontier)At idle: 660 to 820 kPa in D and 720 to 1,080 in R. At stall: 1,270 to 1,500 in D and 1,530 to 1,950 in R
First-design solenoids, with a separate computer (2003 G35)3 to 9 Ω; the low coast brake solenoid, 20 to 40 Ω
Pan bolts22, at 7.9 N·m; Nissan says to always replace them, because they're self-sealing

According to Nissan, line pressure that's low in every range points to a worn pump, the regulator valve, a leak between the strainer and the pump or a low idle; low in only one range, to a leak after the manual valve; and high, to the throttle or temperature sensor, a line pressure solenoid stuck off or a clogged filter.

Which fluid does the RE5R05A take, and how much?

  • Nissan calls for Matic S and accepts Matic J if it isn't available; manuals up to 2005 called for Matic J only. The Mexico table in the 2016 Frontier manual says the same. Nissan warns that another fluid harms driveability and transmission durability.
  • It takes about 10.3 liters (4.0 V6 and 350Z) or 10.6 (5.6 V8). Nissan says that's a reference: the level is set with the dipstick.
  • Check the level at idle in P, after moving the lever through every position: in the COLD range with the fluid at 30 to 50 °C, and in the HOT range at 50 to 80 °C. Don't overfill it.
  • The 4x4 transfer case takes a different fluid (Matic D): don't mix them.
  • To change it, Nissan warms the fluid to about 80 °C, drains it at the plug, refills the same amount and flushes the coolers with new fluid; if it comes out dirty, it repeats.

Nissan reads the fluid like this: very dark or burnt means an internal problem; with clutch material, replace the radiator and flush the cooler lines; with varnish, burnt clutches; milky or cloudy, water in the fluid. And whenever the transmission is repaired or replaced, it says to inspect and clean the cooler in the radiator.

How often should the fluid be changed?

In Mexico, the 2016 Frontier manual says to check the level and leaks every 20,000 km or 12 months, and to change the fluid every 40,000 km or 24 months if you tow or drive on rough, muddy or desert roads. The coolant is first replaced at 160,000 km or 96 months, then every 80,000 km or 48 months, and its mix is checked every 40,000 km. NHTSA's review quotes a dealer's theory that depleted coolant contributes to the cooler cracks; it isn't proven, but it's one more reason to follow that schedule.

US recalls and warranties

We found no recalls, PROFECO campaigns or warranty extensions that name Mexico for these trucks. In the US:

  • Radiator warranty extension (2012) for all 2005 to 2010 automatic Frontier, Pathfinder and Xterra trucks, for the fluid cooler cracks (see above).
  • 14V803 (2014): 194 2015 Armadas whose parking pawl might not fully engage; Nissan replaced the transmissions.
  • 04V408 (2004), 13V094 and 13V095 (2013): the column shifter on the 2004 Titan and on 2012 and 2013 Titans and NV vans.

If your truck came from the US, check its VIN for open recalls.

RE5R05A myths

  • "In limp mode it holds 3rd." According to Nissan, the RE5R05A holds 2nd, 4th or 5th, depending on the fault; never 3rd.
  • "P1762 leaves it in 1st." According to Nissan, a direct clutch solenoid fault leaves it in 4th; a mechanical failure can feel different.
  • "The radiator extension covers the Titan and Armada, or applies in Mexico." Nissan limited it to 2005 to 2010 automatic Frontier, Pathfinder and Xterra trucks, and the court settlement covered only the US and its territories.
  • "The radiator was fixed from 2011." We found no Nissan document on a design change.
  • "It takes Matic D." That fluid is for the transfer case; the RE5R05A takes Matic S or Matic J.
  • "Swap the solenoids and there's nothing to program." Nissan's new valve body comes with a blank computer that has to be programmed with its scan tool.
  • "The NP300 Frontier and the automatic Frontier 2.5 have the RE5R05A." The NP300 Frontier (D23) was manual in 2016 and a 7-speed from 2017; in Mexico, the automatic Frontiers with this unit are 4.0 V6s.
  • "P0750 and P0755 are its shift solenoids." Nissan names each solenoid after its clutch, P1752 to P1774; P0894 isn't a code for this transmission either.
  • "The Murano, Altima or Quest have the RE5R05A." They're front-wheel drive: they use a different automatic or a CVT.

How is it diagnosed?

  • Check the level on the dipstick, hot, and the fluid's color: if it's pink or milky, check the radiator before anything else.
  • Read the codes with a scan tool that reaches the transmission computer, or with the O/D OFF lamp self-diagnosis.
  • If it's stuck in one gear, turn the engine off for 10 seconds. If the fault comes back, check the case connector pins and the computer's power and ground.
  • With harsh shifts or slipping, measure line pressure and stall speed against the values in your year's manual.
  • Before replacing the valve body, confirm who will program the new computer.
  • After repairing or replacing the transmission, flush the cooler in the radiator, as Nissan requires.

See RE5R05A parts

TSS parts for the RE5R05A

The RE5R05A page has every TSS part for this transmission. These are the ones that match the failures in this guide:

Full rebuild (for example, after coolant got in)Rojo overhaul kit, 3-piston kit, input clutch friction plates and V6 steel plate pack
Stuck in 5th or no 5th (the front brake band)1.250" overdrive band
P0745, P0740, P0744 and P1757 (line pressure, converter and band)EPC, TCC and band solenoid
P1772 and P1774 (low coast brake)10 to 15 Ω low coast brake solenoid or 20 to 40 Ω
LeaksPan gasket and pump seal
PumpPump bushing

TSS sells the low coast brake solenoid in two versions, 10 to 15 Ω and 20 to 40 Ω: measure yours before ordering. Individual solenoids are for repairing the valve body; Nissan, on the other hand, sells the complete valve body with its computer. Confirm with your distributor that each part fits your transmission by model, engine and year. The difference between the Rojo and Dorado kits is in our guide to TSS overhaul kits.

TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • Which trucks have the RE5R05A transmission in Mexico?

    According to Nissan Mexicana, the 2005 to 2012 Pathfinder (4.0 V6), the automatic Frontier 4.0 V6 (SE V6 in 2008, SV V6 and PRO-4X, and S and PRO-4X in 2016), the Titan and Armada 5.6 V8 (2005 to 2014) and, as an option, the 350Z. The Xterra, the NV vans and the Infinitis with this unit weren't sold new in Mexico, so the ones there are imports.

  • How do I know if my transmission is an RE5R05A and not the 7-speed?

    Count the gears: the RE5R05A has 5, with a 3.842 (V6), 3.827 (V8) or 3.540 (350Z) first gear. In the model code on the ID plate, the seventh character "N" means the 5-speed automatic. It also has a bolt-held dipstick and a 22-bolt pan. From 2017, the Titan, Armada and NV vans use a 7-speed.

  • Which fluid does the RE5R05A take, and how many liters?

    Nissan calls for Matic S and accepts Matic J; manuals up to 2005 called for Matic J only. It takes about 10.3 liters in the V6 and the 350Z, and 10.6 in the V8. Set the level on the dipstick: COLD with the fluid at 30 to 50 °C, HOT at 50 to 80 °C. Don't overfill it.

  • How often should RE5R05A fluid be changed in Mexico?

    Nissan's schedule for Mexico (2016 Frontier) says to check the level and leaks every 20,000 km, and to change the fluid every 40,000 km or 24 months if you tow or drive on rough, muddy or desert roads. When changing it, Nissan also flushes the coolers.

  • Why did my transmission fluid come out pink or like a milkshake?

    Because it has water or coolant in it: Nissan says to change it and find where it gets in. On 2005 to 2010 Frontier, Pathfinder and Xterra trucks, Nissan documented in the US cracks in the fluid cooler inside the radiator. Owners reported slipping, jerking, delayed shifts and loss of power, and many had to replace the radiator and the transmission.

  • Why is my Frontier or Pathfinder stuck in one gear?

    That's Nissan's limp mode: 4th for a fault in the input, direct or HLR clutch solenoid; 5th or 4th for the front brake solenoid; and 2nd for an interlock fault. Read the codes. Turning the engine off for 10 seconds clears it only if there's no real fault.

  • What do codes P1752, P1757, P1762, P1767, P1772 and P1774 mean?

    They're faults in the solenoids for the input clutch (P1752), front brake (P1757), direct clutch (P1762), HLR clutch (P1767) and low coast brake (P1772 and P1774). Nissan first checks the case connector pins and the computer's power and ground, then replaces the valve body with its computer.

  • If I replace the valve body, does it need programming?

    Yes, if it's Nissan's: the computer is mounted on the valve body, comes blank, and Nissan writes the vehicle's data with its scan tool, with the key ON, the lever in P and the fluid at 72 °C or less. If the old computer can be read, Nissan says to save its data first.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.