Featured: TSS RTD Link by HP Tuners
Black Friday15% off TSS kits · Nov 27–3015% off TSS kits · ends Nov 30
TSS Genuine Parts — home
TSS blog

Ford CD4E transmission problems: 2001-2008 Escape

TSS editorial team · · 12 min read

Macro view of automatic transmission steel clutch drum splines and engagement teeth for Ford CD4E
In short
  • The CD4E is Ford's 4-speed automatic in the 2001 to 2008 Escape, the Contour and the Mystique; Mazda calls it LA4AX-EL and used it in the US Tribute.
  • Ford names it for Mexico in its bulletin 06-11-7, for a shudder on the 2001 to 2003 Escape 3.0; from 2009, the V6 Escape has the 6F35.
  • Failures Ford documents in the US: lost 2nd and 4th from the band, poor cold-weather lubrication, engine stalls at stops from the converter, and cooler leaks.
  • The five solenoids and the temperature sensor sit on one solenoid body that Ford replaces as a unit; with a stuck solenoid it can start in 2nd or 4th.
  • It takes MERCON V and never additives; the filter is inside the transmission, and a drain only removes about 3.7 of its 9.5 liters.

The CD4E is the 4-speed automatic Ford used from 1994 to 2008 in front-wheel-drive cars and SUVs: the 2001 to 2008 Escape, the Contour and the Mystique and, in the US, also the Probe, the Cougar, the Mercury Mariner and the Mazda Tribute. This guide pulls together what Ford's service manuals and bulletins say: which Fords have it in Mexico, its problems by symptom, what the transmission does when a solenoid fails, the codes, test values, the fluid and TSS parts. If you don't know which transmission your Ford has, see which transmission does my Ford have.

What is the CD4E?

What it isA Ford 4-speed electronic overdrive automatic for front-wheel drive (a transaxle), with a chain between the converter and the gearsets; Ford built it in Batavia, Ohio
Mazda nameLA4AX-EL (CD4E) in Mazda's Tribute manual; catalogs list it as LA4A-EL
Ratios1st 2.89, 2nd 1.57, 3rd 1.00, 4th 0.69 and reverse 2.31
ComputerThe engine computer (PCM); there's no separate module
SolenoidsFive: two shift solenoids (A and B), the pressure solenoid (EPC), the converter solenoid (TCC) and the 3-2 timing and coast clutch solenoid. They sit with the temperature sensor on one solenoid body that Ford replaces as a unit
SensorsTurbine speed, output speed (it reads the park gear teeth) and range, on top of the case
BandJust one, the intermediate and overdrive band (2-4 band): it works in 2nd and 4th
FilterIt's inside the transmission: it isn't changed in a fluid change
DipstickYes: the level is checked hot, with the engine running in P
ID tagA tag on the transmission case
Don't confuse it withThe Focus and Mazda3's 4F27E, a different transmission with different ratios: no Escape used it
When it endedOn the 2008 Escape; from 2009, the V6 Escape has the 6-speed 6F35

Which Fords have it in Mexico?

Escape 2001 to 2003 (3.0 V6)Ford names the CD4E in its bulletin 06-11-7, marked "Mexico only", for a transmission shudder on that era's Escape 3.0
Escape 2004 to 2007A 4-speed automatic: the CD4E, per Ford's US documents
Escape 2008 (2.3 and 3.0 V6)"Transmisión automática de 4 velocidades" with both engines: the CD4E
Escape 2009 onNo: the V6 has the 6-speed 6F35
Contour 1998 (2.0 and 2.5 V6)"Automático: Electrónico de 4 velocidades con Sobremarcha": the CD4E, per Ford's US documents
Mystique 1998 (2.5 V6)"Transmisión Automática de 4-velocidades": the CD4E
Mondeo 2001 to 2003"Automática de 4 velocidades"; Ford doesn't name the unit: probably the CD4E
Mazda TributeMazda México didn't sell it; the 2001 to 2008 US Tribute has the CD4E

Ford México doesn't publish the transmission code on its spec sheets: except for bulletin 06-11-7, we infer it from Ford's US documents for the same model, engine and year. Hybrid Escape, Mariner and Tribute models use a different transmission and aren't covered here.

CD4E problems by symptom

These are the diagnostic routines in Ford's service manual and what its bulletins and recalls say, US documents except 06-11-7:

Loses 2nd and 4th gearsBoth use the same band, the intermediate and overdrive band. On US 2007 and 2008 Escape and Mariner models, Ford replaces the band (with light lining for 4-cylinder engines and dark lining for the V6) and selects the servo rod by measuring its travel
Transmission failure after cold startsOn 2001 to 2008 Escape and Mariner models, Ford found failures from poor lubrication during warm-up in cold weather: every repair or replacement gets a new cold-weather cooler bypass kit
The engine stalls when stopping or shifting into D or ROn Escape and Mariner models built from August 2004 to February 15, 2007, internal converter wear keeps it from unlocking; there may be no codes. On the 2001 to 2003 V6 Escape, Ford reprogrammed the computer because the engine stalled when decelerating (recall 04V-165, US)
Harsh, late 1-2 and 2-3 shifts after a repairA wrong turbine speed sensor: Ford used several and calls for the one that matches the vehicle; it sets ratio codes, P0741 or P1744
No forwardThe forward and coast clutch: seals, piston, frictions or a snap ring misaligned with the piston legs (a 2000 bulletin for the Contour, Mystique, Probe, Cougar and 2001 Escape)
No reverseShift solenoid A stuck on (it also removes reverse), the range sensor, the reverse and low/reverse clutches, and line pressure
Transmission shudder (2001 to 2003 Escape 3.0)Ford's bulletin 06-11-7 for Mexico: a fluid change and a computer reprogram
Harsh shifts or engagementsThe pressure solenoid (EPC), the temperature sensor, the 3-2 timing and coast solenoid, the range sensor, the throttle sensor and the MAF; also broken engine mounts
Soft or slipping shiftsLow line pressure: low fluid, a clogged filter, a loose valve body or the pump; if pressure is fine, that shift's clutch
Overheats (P1783)The fluid went above 127 °C (270 °F): the level (overfilling also overheats it), a clogged or reversed cooler or cooler tubes, engine overheating or a converter that won't lock up
LeaksThe axle and converter seals, the covers, the dipstick tube and the cooler; on the US 2008 Escape, Ford ran a program for a cooler tube that cracked
Won't start in P, but starts in NFord had a 1998 bulletin for this (Contour, Probe, Cougar and Mystique); the starting circuit runs through the range sensor

Stuck in one gear: the shift solenoids

This is Ford's 2002 Escape chart with a stuck shift solenoid, with the lever in D (overdrive on):

Solenoid A always off2nd, 2nd, 3rd and 3rd
Solenoid B always offStarts in 4th: 4th, 3rd, 3rd and 4th; no movement in manual 1
Solenoid A always on1st, 1st, 4th and 4th, and no reverse
Solenoid B always on1st, 2nd, 2nd and 1st

Ford doesn't describe a single-gear limp mode: it gives the result for each solenoid. A solenoid that's "off" can be the solenoid, the wiring or the computer, and ratio codes can also be set by stuck valves or damaged frictions.

CD4E trouble codes

P0731, P0732, P0733 and P0734Incorrect ratio in 1st, 2nd, 3rd or 4th: solenoid A or B or internal parts, such as stuck valves or damaged frictions (guide)
P0750 and P0753; P0755 and P0758Solenoid A or B circuit (guide)
P0751, P0756, P1751, P1756, P1714 and P1715Mechanical or hydraulic failure of solenoid A or B; with P1751 and P1756 the O/D OFF light flashes
P0743, P0740, P1742 and P1743Converter solenoid: on or stuck, the engine stalls in manual 2 or at low speed, lugs, or shifts are harsh
P0741 and P1744The converter slips at full lockup: the computer unlocks it and sets EPC pressure to minimum
P1747, P1760 and P1746 (from 2005, P0962, P0748, P0960 and P0963)Pressure solenoid (EPC): shorted to ground, the computer limits the engine, which seems to misfire, and gives minimum pressure; open or shorted to voltage, maximum pressure and harsh shifts
P1789 and P1788 (from 2005, P0966, P0964 and P0967)3-2 timing and coast solenoid: shorted, late 3-2 downshifts and no engine braking; open, engine braking in 2nd and 3rd and harsh 3-2 and 4-3 downshifts
P0707, P0708 and P1702Range sensor: no 4th, firm shifts and no manual 1st (guide)
P0715, P0717 and P0718Turbine speed sensor: no converter lockup, harsh shifts and no 4th (guide)
P0720, P0721 and P0722Output speed sensor: harsh, mistimed shifts
P0711, P0712 and P0713Fluid temperature sensor, on the solenoid body: wrong converter lockup and pressure (guide)
P1783The fluid went above 127 °C (270 °F): the computer raises pressure. A US Ford bulletin ties it to cold-climate shift problems
P1780The O/D OFF button doesn't change state

The O/D OFF light flashes for several transmission faults, not just electrical ones (what each light means). Before opening the transmission, Ford fixes engine codes first (temperature, throttle, MAF, misfires): they can cause harsh shifts or keep the converter from locking up. You can look up other codes in our diagnosis by code.

Test values

Shift solenoids A and B12 to 22 Ω
Converter solenoid12.5 to 19.0 Ω
Pressure solenoid (EPC) and 3-2 timing and coast solenoid3.75 to 5.92 Ω
Any solenoid or sensor to groundMore than 10,000 Ω
Turbine speed sensor550 to 1,200 Ω in the 2002 manual; it changes with the sensor version
Output speed sensor503 to 1,010 Ω
Line pressure at idle, in D, 2 and 1324 to 372 kPa (47 to 54 psi)
Line pressure at idle, in P, N and R441 to 524 kPa (64 to 76 psi)
Stall speed (3.0 V6)2,586 to 2,963 rpm
Cooler flowAbout 1 liter (1 quart) in 15 seconds, at idle in N

These are values from Ford's service manual for the 2002 Escape 3.0 (US). If a solenoid is out of range or shorted, Ford replaces the whole solenoid body. Ford runs the pressure test first, and if pressure is low at stall it skips the stall test; never more than 5 seconds at full throttle. A high stall speed means a clutch or the band is slipping.

Which fluid does it take, and how is it checked?

Today Ford and Mazda call for MERCON V in the CD4E. Early units came with MERCON, and in 2006, with its bulletin 06-14-4, Ford moved the 2001 to 2007 Escape, the Contour, the Mystique and others to MERCON V. Don't use additives or cleaners, which Ford prohibits, or "universal" fluids: Mazda warns they can damage the transmission.

It holds about 9.5 liters in total. A drain only removes about 3.7 liters, and the filter is inside the transmission. That's why Ford refills 3.7 liters, moves the lever through every position for 5 minutes at idle and drains again to get more fluid out of the converter. If the drained fluid has a lot of metal or friction material, the transmission needs repair.

It has a dipstick. Ford checks the level hot (after about 30 km or 20 miles), on level ground, with the engine running, after moving the lever through every position and back to P. Overfilling can overheat the transmission and make it fail, and above 10 °C (50 °F) outside you shouldn't drive if the level is below the hole in the dipstick. Fluid should be red, not brown or black; a burnt smell means overheating or damaged frictions or band.

After a repair, Ford flushes the cooler and its lines on almost all its transmissions, but on the Escape and Mariner with the CD4E it says something else: fit a new cold-weather cooler bypass kit, without flushing the old bypass or tubes. More in our cooler and fluid leak guides.

CD4E myths

  • "The 2008 Escape has the 6F35." The 2008 Mexican spec sheet says 4-speed automatic with both engines; the 6F35 arrived with the 2009 Escape.
  • "The Escape 2.3 has the 4F27E." Ford and Mazda say the 2001 to 2008 Escape and Tribute have the CD4E.
  • "The CD4E is a Mazda transmission." Ford built it in Batavia, Ohio; Mazda used it in the Tribute.
  • "It's always the solenoids." Sometimes, but Ford also documents the band, the forward clutch, cold-weather lubrication, the converter and cooler leaks.
  • "You replace just the bad solenoid." Ford replaces the whole solenoid body.
  • "A flashing O/D OFF light means an electrical fault." It also flashes for mechanical or hydraulic solenoid failures.
  • "A fluid change includes the filter." The filter is inside the transmission.
  • "MERCON V damages the CD4E." Ford and Mazda call for MERCON V in this transmission.
  • "Additives or cleaners extend its life." Ford prohibits them.
  • "If it stalls when braking, it's the transmission." It can be the engine calibration (the US recall for the 2001 to 2003 V6 Escape), the converter solenoid or the converter.
  • "The Escape's transmission had an extended warranty." We found no recall or warranty extension for CD4E internal failures; the only transmission defect with a recall was a shift lever bolt on some units rebuilt in 2015, in the US.
  • "Disconnecting the battery fixes the transmission." It only erases what it learned: after 20 minutes disconnected, the computer relearns its shifts.

How is it diagnosed?

  • Check the fluid level and condition hot, with the engine running in P.
  • Read the codes with the car warm and before touching connectors: Ford fixes engine codes first and transmission codes second.
  • Check the transmission's round connector, the range sensor's and the speed sensors'.
  • Measure the solenoids from the case connector and the sensors against Ford's values.
  • Run the line pressure test, then the stall test.
  • If the transmission or the turbine speed sensor was replaced, confirm it's the right sensor.
  • Only then open the transmission: the valve body and solenoid body come out with the transmission in the car.

If you swap the transmission, confirm the turbine speed sensor is the right one and fit the cold-weather cooler bypass kit. After a battery disconnect of more than 20 minutes, the transmission relearns its shifts and may shift harshly at first.

See CD4E parts

TSS parts for the CD4E

The CD4E page has every TSS part for this transmission. These are the ones that match the jobs in this guide:

Filter and gaskets when the transmission is openedInternal filter and pan or Farpak pan gaskets
Range sensorCD4E TR switch
Speed sensorsTurbine, black connector (not for the Probe) and output, 1998 on; on the Contour, 2.0 or 2.5 V6
Loses 2nd and 4th42 mm intermediate band
Slipping, or no forward or reverseFriction plate kit, or the forward and low/reverse plates
Transmission overhaulDorado gasket kit, 2003 on or H-D kit, pump gasket 1997 on or 1994 to 1996, pump O-ring and converter bushing
LeaksAxle seal and case gasket

The TSS CD4E solenoid set and converters are out of stock for now. Ford picks the band by engine (light lining for 4 cylinders and dark for the V6): compare it with the one you remove and confirm with Veinte 07. The Dorado kit says 2003 on and the pump gasket changes in 1997: confirm the year before ordering. If you're torn between gasket kits, read how they differ.

TSS is an aftermarket brand with OEM-comparable quality and quality control on every product. You can buy it from our authorized distributors: in the United States from Sun Transmissions, and in Mexico the full TSS catalog at Transmisiones Veinte 07.

All articles
Common questions

Frequently asked questions

What people ask us most about this topic.

  • Which transmission does the 2001 to 2008 Ford Escape have?

    The CD4E 4-speed automatic. Ford names it in a bulletin for Mexican 2001 to 2003 Escape 3.0 models, and the 2008 Mexican spec sheet says 4-speed automatic with the 2.3 and the V6. From 2009, the V6 has the 6F35.

  • Are the CD4E and the LA4A-EL the same transmission?

    Yes: Mazda calls it LA4AX-EL (CD4E) in its Tribute manual, and catalogs list it as LA4A-EL.

  • Why did my Escape lose 2nd and 4th?

    Both use the same band, the intermediate and overdrive band. On US 2007 and 2008 Escapes, Ford replaces the band and selects the servo rod by measuring its travel.

  • Why does my Escape stall when braking?

    It can be a converter that won't unlock, the converter solenoid or, on 2001 to 2003 V6 models, the engine calibration Ford corrected in the US. Read the codes first.

  • Which fluid does the CD4E take?

    MERCON V. Early units came with MERCON, and since 2006 Ford services them with MERCON V. Don't use additives.

  • How many liters does the CD4E hold?

    About 9.5 liters in total. A drain only removes about 3.7 liters: Ford refills, moves the lever through every position and drains again. Top off by the dipstick with the fluid hot.

  • Does the CD4E have a filter?

    Yes, but it's inside the transmission: it isn't changed in a normal fluid change.

  • Is there a campaign for the Escape's transmission?

    We found no recall or warranty extension for CD4E internal failures. In the US, Ford reprogrammed the computer on 2001 to 2003 V6 Escapes that stalled when decelerating, and the 2008 Escape had a program for a cooler tube that cracked.

Buying wholesale or own a parts store?

We'll send you a quote or tell you how to sell TSS in your area.